1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
2
3OMAP CONTROL PHY
4
5Required properties:
6 - compatible: Should be one of
7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
9                        e.g. USB2_PHY on OMAP5.
10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
11                        e.g. USB3 PHY and SATA PHY on OMAP5.
12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
13			set PCS delay value.
14			e.g. PCIE PHY in DRA7x
15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
16                        DRA7 platform.
17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
18                        AM437 platform.
19 - reg : register ranges as listed in the reg-names property
20 - reg-names: "otghs_control" for control-phy-otghs
21	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
22	      "power" for all other types
23
24omap_control_usb: omap-control-usb@4a002300 {
25        compatible = "ti,control-phy-otghs";
26        reg = <0x4a00233c 0x4>;
27        reg-names = "otghs_control";
28};
29
30TI PIPE3 PHY
31
32Required properties:
33 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
34   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
35 - reg : Address and length of the register set for the device.
36 - reg-names: The names of the register addresses corresponding to the registers
37   filled in "reg".
38 - #phy-cells: determine the number of cells that should be given in the
39   phandle while referencing this phy.
40 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
41   clock-names.
42 - clock-names: should include:
43   * "wkupclk" - wakeup clock.
44   * "sysclk" - system clock.
45   * "refclk" - reference clock.
46   * "dpll_ref" - external dpll ref clk
47   * "dpll_ref_m2" - external dpll ref clk
48   * "phy-div" - divider for apll
49   * "div-clk" - apll clock
50
51Optional properties:
52 - id: If there are multiple instance of the same type, in order to
53   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
54   PHY). If "id" is not provided, it is set to default value of '1'.
55 - syscon-pllreset: Handle to system control region that contains the
56   CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
57   register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
58 - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
59   register offset to write the PCS delay value.
60
61Deprecated properties:
62 - ctrl-module : phandle of the control module used by PHY driver to power on
63   the PHY.
64
65Recommended properies:
66 - syscon-phy-power : phandle/offset pair. Phandle to the system control
67   module and the register offset to power on/off the PHY.
68
69This is usually a subnode of ocp2scp to which it is connected.
70
71usb3phy@4a084400 {
72	compatible = "ti,phy-usb3";
73	reg = <0x4a084400 0x80>,
74	      <0x4a084800 0x64>,
75	      <0x4a084c00 0x40>;
76	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
77	ctrl-module = <&omap_control_usb>;
78	#phy-cells = <0>;
79	clocks = <&usb_phy_cm_clk32k>,
80		 <&sys_clkin>,
81		 <&usb_otg_ss_refclk960m>;
82	clock-names =	"wkupclk",
83			"sysclk",
84			"refclk";
85};
86
87sata_phy: phy@4a096000 {
88	compatible = "ti,phy-pipe3-sata";
89	reg = <0x4A096000 0x80>, /* phy_rx */
90	      <0x4A096400 0x64>, /* phy_tx */
91	      <0x4A096800 0x40>; /* pll_ctrl */
92	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
93	ctrl-module = <&omap_control_sata>;
94	clocks = <&sys_clkin1>, <&sata_ref_clk>;
95	clock-names = "sysclk", "refclk";
96	syscon-pllreset = <&scm_conf 0x3fc>;
97	#phy-cells = <0>;
98};
99