1TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs
2
3OMAP CONTROL PHY
4
5Required properties:
6 - compatible: Should be one of
7 "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4.
8 "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register
9                        e.g. USB2_PHY on OMAP5.
10 "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control
11                        e.g. USB3 PHY and SATA PHY on OMAP5.
12 "ti,control-phy-pcie" - for pcie to support external clock for pcie and to
13			set PCS delay value.
14			e.g. PCIE PHY in DRA7x
15 "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on
16                        DRA7 platform.
17 "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on
18                        AM437 platform.
19 - reg : register ranges as listed in the reg-names property
20 - reg-names: "otghs_control" for control-phy-otghs
21	      "power", "pcie_pcs" and "control_sma" for control-phy-pcie
22	      "power" for all other types
23
24omap_control_usb: omap-control-usb@4a002300 {
25        compatible = "ti,control-phy-otghs";
26        reg = <0x4a00233c 0x4>;
27        reg-names = "otghs_control";
28};
29
30OMAP USB2 PHY
31
32Required properties:
33 - compatible: Should be "ti,omap-usb2"
34	       Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on
35	       DRA7x
36	       Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY
37	       in DRA7x
38	       Should be "ti,am654-usb2" for the USB2 PHYs on AM654.
39 - reg : Address and length of the register set for the device.
40 - #phy-cells: determine the number of cells that should be given in the
41   phandle while referencing this phy.
42 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
43   clock-names.
44 - clock-names: should include:
45   * "wkupclk" - wakeup clock.
46   * "refclk" - reference clock (optional).
47
48Deprecated properties:
49 - ctrl-module : phandle of the control module used by PHY driver to power on
50   the PHY.
51
52Recommended properies:
53- syscon-phy-power : phandle/offset pair. Phandle to the system control
54  module and the register offset to power on/off the PHY.
55
56This is usually a subnode of ocp2scp to which it is connected.
57
58usb2phy@4a0ad080 {
59	compatible = "ti,omap-usb2";
60	reg = <0x4a0ad080 0x58>;
61	ctrl-module = <&omap_control_usb>;
62	#phy-cells = <0>;
63	clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>;
64	clock-names = "wkupclk", "refclk";
65};
66
67TI PIPE3 PHY
68
69Required properties:
70 - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or
71   "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated.
72 - reg : Address and length of the register set for the device.
73 - reg-names: The names of the register addresses corresponding to the registers
74   filled in "reg".
75 - #phy-cells: determine the number of cells that should be given in the
76   phandle while referencing this phy.
77 - clocks: a list of phandles and clock-specifier pairs, one for each entry in
78   clock-names.
79 - clock-names: should include:
80   * "wkupclk" - wakeup clock.
81   * "sysclk" - system clock.
82   * "refclk" - reference clock.
83   * "dpll_ref" - external dpll ref clk
84   * "dpll_ref_m2" - external dpll ref clk
85   * "phy-div" - divider for apll
86   * "div-clk" - apll clock
87
88Optional properties:
89 - id: If there are multiple instance of the same type, in order to
90   differentiate between each instance "id" can be used (e.g., multi-lane PCIe
91   PHY). If "id" is not provided, it is set to default value of '1'.
92 - syscon-pllreset: Handle to system control region that contains the
93   CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0
94   register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy.
95 - syscon-pcs : phandle/offset pair. Phandle to the system control module and the
96   register offset to write the PCS delay value.
97
98Deprecated properties:
99 - ctrl-module : phandle of the control module used by PHY driver to power on
100   the PHY.
101
102Recommended properies:
103 - syscon-phy-power : phandle/offset pair. Phandle to the system control
104   module and the register offset to power on/off the PHY.
105
106This is usually a subnode of ocp2scp to which it is connected.
107
108usb3phy@4a084400 {
109	compatible = "ti,phy-usb3";
110	reg = <0x4a084400 0x80>,
111	      <0x4a084800 0x64>,
112	      <0x4a084c00 0x40>;
113	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
114	ctrl-module = <&omap_control_usb>;
115	#phy-cells = <0>;
116	clocks = <&usb_phy_cm_clk32k>,
117		 <&sys_clkin>,
118		 <&usb_otg_ss_refclk960m>;
119	clock-names =	"wkupclk",
120			"sysclk",
121			"refclk";
122};
123
124sata_phy: phy@4a096000 {
125	compatible = "ti,phy-pipe3-sata";
126	reg = <0x4A096000 0x80>, /* phy_rx */
127	      <0x4A096400 0x64>, /* phy_tx */
128	      <0x4A096800 0x40>; /* pll_ctrl */
129	reg-names = "phy_rx", "phy_tx", "pll_ctrl";
130	ctrl-module = <&omap_control_sata>;
131	clocks = <&sys_clkin1>, <&sata_ref_clk>;
132	clock-names = "sysclk", "refclk";
133	syscon-pllreset = <&scm_conf 0x3fc>;
134	#phy-cells = <0>;
135};
136