1TI PCI Controllers 2 3PCIe DesignWare Controller 4 - compatible: Should be "ti,dra7-pcie" for RC (deprecated) 5 Should be "ti,dra7-pcie-ep" for EP (deprecated) 6 Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode 7 Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode 8 Should be "ti,dra726-pcie-rc" for dra72x in RC mode 9 Should be "ti,dra726-pcie-ep" for dra72x in EP mode 10 - phys : list of PHY specifiers (used by generic PHY framework) 11 - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the 12 number of PHYs as specified in *phys* property. 13 - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", 14 where <X> is the instance number of the pcie from the HW spec. 15 - num-lanes as specified in ../designware-pcie.txt 16 - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control 17 module and the register offset to specify lane 18 selection. 19 20HOST MODE 21========= 22 - reg : Two register ranges as listed in the reg-names property 23 - reg-names : The first entry must be "ti-conf" for the TI-specific registers 24 The second entry must be "rc-dbics" for the DesignWare PCIe 25 registers 26 The third entry must be "config" for the PCIe configuration space 27 - interrupts : Two interrupt entries must be specified. The first one is for 28 main interrupt line and the second for MSI interrupt line. 29 - #address-cells, 30 #size-cells, 31 #interrupt-cells, 32 device_type, 33 ranges, 34 interrupt-map-mask, 35 interrupt-map : as specified in ../designware-pcie.txt 36 - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument 37 should contain the register offset within syscon 38 and the 2nd argument should contain the bit field 39 for setting the bit to enable unaligned 40 access. 41 42DEVICE MODE 43=========== 44 - reg : Four register ranges as listed in the reg-names property 45 - reg-names : "ti-conf" for the TI-specific registers 46 "ep_dbics" for the standard configuration registers as 47 they are locally accessed within the DIF CS space 48 "ep_dbics2" for the standard configuration registers as 49 they are locally accessed within the DIF CS2 space 50 "addr_space" used to map remote RC address space 51 - interrupts : one interrupt entries must be specified for main interrupt. 52 - num-ib-windows : number of inbound address translation windows 53 - num-ob-windows : number of outbound address translation windows 54 - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument 55 should contain the register offset within syscon 56 and the 2nd argument should contain the bit field 57 for setting the bit to enable unaligned 58 access. 59 60Optional Property: 61 - gpios : Should be added if a GPIO line is required to drive PERST# line 62 63NOTE: Two DT nodes may be added for each PCI controller; one for host 64mode and another for device mode. So in order for PCI to 65work in host mode, EP mode DT node should be disabled and in order to PCI to 66work in EP mode, host mode DT node should be disabled. Host mode and EP 67mode are mutually exclusive. 68 69Example: 70axi { 71 compatible = "simple-bus"; 72 #size-cells = <1>; 73 #address-cells = <1>; 74 ranges = <0x51000000 0x51000000 0x3000 75 0x0 0x20000000 0x10000000>; 76 pcie@51000000 { 77 compatible = "ti,dra7-pcie"; 78 reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; 79 reg-names = "rc_dbics", "ti_conf", "config"; 80 interrupts = <0 232 0x4>, <0 233 0x4>; 81 #address-cells = <3>; 82 #size-cells = <2>; 83 device_type = "pci"; 84 ranges = <0x81000000 0 0 0x03000 0 0x00010000 85 0x82000000 0 0x20013000 0x13000 0 0xffed000>; 86 #interrupt-cells = <1>; 87 num-lanes = <1>; 88 ti,hwmods = "pcie1"; 89 phys = <&pcie1_phy>; 90 phy-names = "pcie-phy0"; 91 interrupt-map-mask = <0 0 0 7>; 92 interrupt-map = <0 0 0 1 &pcie_intc 1>, 93 <0 0 0 2 &pcie_intc 2>, 94 <0 0 0 3 &pcie_intc 3>, 95 <0 0 0 4 &pcie_intc 4>; 96 pcie_intc: interrupt-controller { 97 interrupt-controller; 98 #address-cells = <0>; 99 #interrupt-cells = <1>; 100 }; 101 }; 102}; 103