1Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices
2------
3
4This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
5The node is expected to be specified as a child node to the SDIO/PCIE controller that
6connects the device to the system.
7
8Required properties:
9
10  - compatible : should be one of the following:
11	* "marvell,sd8787"
12	* "marvell,sd8897"
13	* "marvell,sd8997"
14	* "pci11ab,2b42"
15	* "pci1b4b,2b42"
16
17Optional properties:
18
19  - marvell,caldata* : A series of properties with marvell,caldata prefix,
20		      represent calibration data downloaded to the device during
21		      initialization. This is an array of unsigned 8-bit values.
22		      the properties should follow below property name and
23		      corresponding array length:
24	"marvell,caldata-txpwrlimit-2g" (length = 566).
25	"marvell,caldata-txpwrlimit-5g-sub0" (length = 502).
26	"marvell,caldata-txpwrlimit-5g-sub1" (length = 688).
27	"marvell,caldata-txpwrlimit-5g-sub2" (length = 750).
28	"marvell,caldata-txpwrlimit-5g-sub3" (length = 502).
29  - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured
30		      to firmware. Firmware will wakeup the host using this pin
31		      during suspend/resume.
32  - interrupt-parent: phandle of the parent interrupt controller
33  - interrupts : interrupt pin number to the cpu. driver will request an irq based on
34		 this interrupt number. during system suspend, the irq will be enabled
35		 so that the wifi chip can wakeup host platform under certain condition.
36		 during system resume, the irq will be disabled to make sure
37		 unnecessary interrupt is not received.
38  - vmmc-supply: a phandle of a regulator, supplying VCC to the card
39  - mmc-pwrseq:  phandle to the MMC power sequence node. See "mmc-pwrseq-*"
40		 for documentation of MMC power sequence bindings.
41
42Example:
43
44Tx power limit calibration data is configured in below example.
45The calibration data is an array of unsigned values, the length
46can vary between hw versions.
47IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured
48so that firmware can wakeup host using this device side pin.
49
50&mmc3 {
51	status = "okay";
52	vmmc-supply = <&wlan_en_reg>;
53	mmc-pwrseq = <&wifi_pwrseq>;
54	bus-width = <4>;
55	cap-power-off-card;
56	keep-power-in-suspend;
57
58	#address-cells = <1>;
59	#size-cells = <0>;
60	mwifiex: wifi@1 {
61		compatible = "marvell,sd8897";
62		reg = <1>;
63		interrupt-parent = <&pio>;
64		interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
65
66		marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 <
67	0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>;
68		marvell,wakeup-pin = <3>;
69	};
70};
71