1# SPDX-License-Identifier: GPL-2.0
2# Copyright (C) 2019 Texas Instruments Incorporated
3%YAML 1.2
4---
5$id: "http://devicetree.org/schemas/net/ti,dp83869.yaml#"
6$schema: "http://devicetree.org/meta-schemas/core.yaml#"
7
8title: TI DP83869 ethernet PHY
9
10allOf:
11  - $ref: "ethernet-controller.yaml#"
12
13maintainers:
14  - Dan Murphy <dmurphy@ti.com>
15
16description: |
17  The DP83869HM device is a robust, fully-featured Gigabit (PHY) transceiver
18  with integrated PMD sublayers that supports 10BASE-Te, 100BASE-TX and
19  1000BASE-T Ethernet protocols. The DP83869 also supports 1000BASE-X and
20  100BASE-FX Fiber protocols.
21  This device interfaces to the MAC layer through Reduced GMII (RGMII) and
22  SGMII The DP83869HM supports Media Conversion in Managed mode. In this mode,
23  the DP83869HM can run 1000BASE-X-to-1000BASE-T and 100BASE-FX-to-100BASE-TX
24  conversions.  The DP83869HM can also support Bridge Conversion from RGMII to
25  SGMII and SGMII to RGMII.
26
27  Specifications about the charger can be found at:
28    http://www.ti.com/lit/ds/symlink/dp83869hm.pdf
29
30properties:
31  reg:
32    maxItems: 1
33
34  ti,min-output-impedance:
35    type: boolean
36    description: |
37       MAC Interface Impedance control to set the programmable output impedance
38       to a minimum value (35 ohms).
39
40  ti,max-output-impedance:
41    type: boolean
42    description: |
43       MAC Interface Impedance control to set the programmable output impedance
44       to a maximum value (70 ohms).
45
46  tx-fifo-depth:
47    $ref: /schemas/types.yaml#definitions/uint32
48    description: |
49       Transmitt FIFO depth see dt-bindings/net/ti-dp83869.h for values
50
51  rx-fifo-depth:
52    $ref: /schemas/types.yaml#definitions/uint32
53    description: |
54       Receive FIFO depth see dt-bindings/net/ti-dp83869.h for values
55
56  ti,clk-output-sel:
57    $ref: /schemas/types.yaml#definitions/uint32
58    description: |
59       Muxing option for CLK_OUT pin see dt-bindings/net/ti-dp83869.h for values.
60
61  ti,op-mode:
62    $ref: /schemas/types.yaml#definitions/uint32
63    description: |
64       Operational mode for the PHY.  If this is not set then the operational
65       mode is set by the straps. see dt-bindings/net/ti-dp83869.h for values
66
67required:
68  - reg
69
70examples:
71  - |
72    #include <dt-bindings/net/ti-dp83869.h>
73    mdio0 {
74      #address-cells = <1>;
75      #size-cells = <0>;
76      ethphy0: ethernet-phy@0 {
77        reg = <0>;
78        tx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
79        rx-fifo-depth = <DP83869_PHYCR_FIFO_DEPTH_4_B_NIB>;
80        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
81        ti,max-output-impedance = "true";
82        ti,clk-output-sel = <DP83869_CLK_O_SEL_CHN_A_RCLK>;
83      };
84    };
85