1* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
2
3This binding is deprecated, but it continues to be supported, but new
4features should be preferably added to the stmmac binding document.
5
6This binding supports the Synopsys Designware Ethernet QoS (Quality Of Service)
7IP block. The IP supports multiple options for bus type, clocking and reset
8structure, and feature list. Consequently, a number of properties and list
9entries in properties are marked as optional, or only required in specific HW
10configurations.
11
12Required properties:
13- compatible: One of:
14  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10"
15    Represents the IP core when integrated into the Axis ARTPEC-6 SoC.
16  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10"
17    Represents the IP core when integrated into the NVIDIA Tegra186 SoC.
18  - "snps,dwc-qos-ethernet-4.10"
19    This combination is deprecated. It should be treated as equivalent to
20    "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10". It is supported to be
21    compatible with earlier revisions of this binding.
22- reg: Address and length of the register set for the device
23- clocks: Phandle and clock specifiers for each entry in clock-names, in the
24  same order. See ../clock/clock-bindings.txt.
25- clock-names: May contain any/all of the following depending on the IP
26  configuration, in any order:
27  - "tx"
28    The EQOS transmit path clock. The HW signal name is clk_tx_i.
29    In some configurations (e.g. GMII/RGMII), this clock also drives the PHY TX
30    path. In other configurations, other clocks (such as tx_125, rmii) may
31    drive the PHY TX path.
32  - "rx"
33    The EQOS receive path clock. The HW signal name is clk_rx_i.
34    In some configurations (e.g. GMII/RGMII), this clock is derived from the
35    PHY's RX clock output. In other configurations, other clocks (such as
36    rx_125, rmii) may drive the EQOS RX path.
37    In cases where the PHY clock is directly fed into the EQOS receive path
38    without intervening logic, the DT need not represent this clock, since it
39    is assumed to be fully under the control of the PHY device/driver. In
40    cases where SoC integration adds additional logic to this path, such as a
41    SW-controlled clock gate, this clock should be represented in DT.
42  - "slave_bus"
43    The CPU/slave-bus (CSR) interface clock. This applies to any bus type;
44    APB, AHB, AXI, etc. The HW signal name is hclk_i (AHB) or clk_csr_i (other
45    buses).
46  - "master_bus"
47    The master bus interface clock. Only required in configurations that use a
48    separate clock for the master and slave bus interfaces. The HW signal name
49    is hclk_i (AHB) or aclk_i (AXI).
50  - "ptp_ref"
51    The PTP reference clock. The HW signal name is clk_ptp_ref_i.
52  - "phy_ref_clk"
53    This clock is deprecated and should not be used by new compatible values.
54    It is equivalent to "tx".
55  - "apb_pclk"
56    This clock is deprecated and should not be used by new compatible values.
57    It is equivalent to "slave_bus".
58
59  Note: Support for additional IP configurations may require adding the
60  following clocks to this list in the future: clk_rx_125_i, clk_tx_125_i,
61  clk_pmarx_0_i, clk_pmarx1_i, clk_rmii_i, clk_revmii_rx_i, clk_revmii_tx_i.
62  Configurations exist where multiple similar clocks are used at once, e.g. all
63  of clk_rx_125_i, clk_pmarx_0_i, clk_pmarx1_i. For this reason it is best to
64  extend the binding with a separate clock-names entry for each of those RX
65  clocks, rather than repurposing the existing "rx" clock-names entry as a
66  generic/logical clock in a similar fashion to "master_bus" and "slave_bus".
67  This will allow easy support for configurations that support multiple PHY
68  interfaces using a mux, and hence need to have explicit control over
69  specific RX clocks.
70
71  The following compatible values require the following set of clocks:
72  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
73    - "slave_bus"
74    - "master_bus"
75    - "rx"
76    - "tx"
77    - "ptp_ref"
78  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
79    - "slave_bus"
80    - "master_bus"
81    - "tx"
82    - "ptp_ref"
83  - "snps,dwc-qos-ethernet-4.10" (deprecated):
84    - "phy_ref_clk"
85    - "apb_clk"
86- interrupts: Should contain the core's combined interrupt signal
87- phy-mode: See ethernet.txt file in the same directory
88- resets: Phandle and reset specifiers for each entry in reset-names, in the
89  same order. See ../reset/reset.txt.
90- reset-names: May contain any/all of the following depending on the IP
91  configuration, in any order:
92  - "eqos". The reset to the entire module. The HW signal name is hreset_n
93    (AHB) or aresetn_i (AXI).
94
95  The following compatible values require the following set of resets:
96  (the reset properties may be omitted if empty)
97  - "nvidia,tegra186-eqos", "snps,dwc-qos-ethernet-4.10":
98    - "eqos".
99  - "axis,artpec6-eqos", "snps,dwc-qos-ethernet-4.10":
100    - None.
101  - "snps,dwc-qos-ethernet-4.10" (deprecated):
102    - None.
103
104Optional properties:
105- dma-coherent: Present if dma operations are coherent
106- phy-reset-gpios: Phandle and specifier for any GPIO used to reset the PHY.
107  See ../gpio/gpio.txt.
108- snps,en-lpi: If present it enables use of the AXI low-power interface
109- snps,write-requests: Number of write requests that the AXI port can issue.
110  It depends on the SoC configuration.
111- snps,read-requests: Number of read requests that the AXI port can issue.
112  It depends on the SoC configuration.
113- snps,burst-map: Bitmap of allowed AXI burst lengths, with the LSB
114  representing 4, then 8 etc.
115- snps,txpbl: DMA Programmable burst length for the TX DMA
116- snps,rxpbl: DMA Programmable burst length for the RX DMA
117- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
118  TX low-power mode.
119- phy-handle: See ethernet.txt file in the same directory
120- mdio device tree subnode: When the GMAC has a phy connected to its local
121    mdio, there must be device tree subnode with the following
122    required properties:
123    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
124    - #address-cells: Must be <1>.
125    - #size-cells: Must be <0>.
126
127    For each phy on the mdio bus, there must be a node with the following
128    fields:
129
130    - reg: phy id used to communicate to phy.
131    - device_type: Must be "ethernet-phy".
132    - fixed-mode device tree subnode: see fixed-link.txt in the same directory
133
134The MAC address will be determined using the optional properties
135defined in ethernet.txt.
136
137Examples:
138ethernet2@40010000 {
139	clock-names = "phy_ref_clk", "apb_pclk";
140	clocks = <&clkc 17>, <&clkc 15>;
141	compatible = "snps,dwc-qos-ethernet-4.10";
142	interrupt-parent = <&intc>;
143	interrupts = <0x0 0x1e 0x4>;
144	reg = <0x40010000 0x4000>;
145	phy-handle = <&phy2>;
146	phy-mode = "gmii";
147	phy-reset-gpios = <&gpioctlr 43 GPIO_ACTIVE_LOW>;
148
149	snps,en-tx-lpi-clockgating;
150	snps,en-lpi;
151	snps,write-requests = <2>;
152	snps,read-requests = <16>;
153	snps,burst-map = <0x7>;
154	snps,txpbl = <8>;
155	snps,rxpbl = <2>;
156
157	dma-coherent;
158
159	mdio {
160		#address-cells = <0x1>;
161		#size-cells = <0x0>;
162		phy2: phy@1 {
163			compatible = "ethernet-phy-ieee802.3-c22";
164			device_type = "ethernet-phy";
165			reg = <0x1>;
166		};
167	};
168};
169