1* NI XGE Ethernet controller
2
3Required properties:
4- compatible: Should be "ni,xge-enet-3.00", but can be "ni,xge-enet-2.00" for
5              older device trees with DMA engines co-located in the address map,
6              with the one reg entry to describe the whole device.
7- reg: Address and length of the register set for the device. It contains the
8       information of registers in the same order as described by reg-names.
9- reg-names: Should contain the reg names
10	"dma":  DMA engine control and status region
11        "ctrl": MDIO and PHY control and status region
12- interrupts: Should contain tx and rx interrupt
13- interrupt-names: Should be "rx" and "tx"
14- phy-mode: See ethernet.txt file in the same directory.
15- nvmem-cells: Phandle of nvmem cell containing the MAC address
16- nvmem-cell-names: Should be "address"
17
18Optional properties:
19- mdio subnode to indicate presence of MDIO controller
20- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory.
21  Use instead of phy-handle.
22- phy-handle: See ethernet.txt file in the same directory.
23
24Examples (10G generic PHY):
25	nixge0: ethernet@40000000 {
26		compatible = "ni,xge-enet-3.00";
27		reg = <0x40000000 0x4000
28		       0x41002000 0x2000>;
29		reg-names = "dma", "ctrl";
30
31		nvmem-cells = <&eth1_addr>;
32		nvmem-cell-names = "address";
33
34		interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
35		interrupt-names = "rx", "tx";
36		interrupt-parent = <&intc>;
37
38		phy-mode = "xgmii";
39		phy-handle = <&ethernet_phy1>;
40
41		mdio {
42			ethernet_phy1: ethernet-phy@4 {
43				compatible = "ethernet-phy-ieee802.3-c45";
44				reg = <4>;
45			};
46		};
47	};
48
49Examples (10G generic PHY, no MDIO):
50	nixge0: ethernet@40000000 {
51		compatible = "ni,xge-enet-2.00";
52		reg = <0x40000000 0x6000>;
53
54		nvmem-cells = <&eth1_addr>;
55		nvmem-cell-names = "address";
56
57		interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
58		interrupt-names = "rx", "tx";
59		interrupt-parent = <&intc>;
60
61		phy-mode = "xgmii";
62		phy-handle = <&ethernet_phy1>;
63	};
64
65Examples (1G generic fixed-link + MDIO):
66	nixge0: ethernet@40000000 {
67		compatible = "ni,xge-enet-2.00";
68		reg = <0x40000000 0x6000>;
69
70		nvmem-cells = <&eth1_addr>;
71		nvmem-cell-names = "address";
72
73		interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>;
74		interrupt-names = "rx", "tx";
75		interrupt-parent = <&intc>;
76
77		phy-mode = "xgmii";
78
79		fixed-link {
80			speed = <1000>;
81			pause;
82			link-gpios = <&gpio0 63 GPIO_ACTIVE_HIGH>;
83		};
84
85		mdio {
86			ethernet_phy1: ethernet-phy@4 {
87				compatible = "ethernet-phy-ieee802.3-c22";
88				reg = <4>;
89			};
90		};
91
92	};
93