1=============================================================================
2Freescale Frame Manager Device Bindings
3
4CONTENTS
5  - FMan Node
6  - FMan Port Node
7  - FMan MURAM Node
8  - FMan dTSEC/XGEC/mEMAC Node
9  - FMan IEEE 1588 Node
10  - FMan MDIO Node
11  - Example
12
13=============================================================================
14FMan Node
15
16DESCRIPTION
17
18Due to the fact that the FMan is an aggregation of sub-engines (ports, MACs,
19etc.) the FMan node will have child nodes for each of them.
20
21PROPERTIES
22
23- compatible
24		Usage: required
25		Value type: <stringlist>
26		Definition: Must include "fsl,fman"
27		FMan version can be determined via FM_IP_REV_1 register in the
28		FMan block. The offset is 0xc4 from the beginning of the
29		Frame Processing Manager memory map (0xc3000 from the
30		beginning of the FMan node).
31
32- cell-index
33		Usage: required
34		Value type: <u32>
35		Definition: Specifies the index of the FMan unit.
36
37		The cell-index value may be used by the SoC, to identify the
38		FMan unit in the SoC memory map. In the table below,
39		there's a description of the cell-index use in each SoC:
40
41		- P1023:
42		register[bit]			FMan unit	cell-index
43		============================================================
44		DEVDISR[1]			1		0
45
46		- P2041, P3041, P4080 P5020, P5040:
47		register[bit]			FMan unit	cell-index
48		============================================================
49		DCFG_DEVDISR2[6]		1		0
50		DCFG_DEVDISR2[14]		2		1
51			(Second FM available only in P4080 and P5040)
52
53		- B4860, T1040, T2080, T4240:
54		register[bit]			FMan unit	cell-index
55		============================================================
56		DCFG_CCSR_DEVDISR2[24]		1		0
57		DCFG_CCSR_DEVDISR2[25]		2		1
58			(Second FM available only in T4240)
59
60		DEVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
61		the specific SoC "Device Configuration/Pin Control" Memory
62		Map.
63
64- reg
65		Usage: required
66		Value type: <prop-encoded-array>
67		Definition: A standard property. Specifies the offset of the
68		following configuration registers:
69		- BMI configuration registers.
70		- QMI configuration registers.
71		- DMA configuration registers.
72		- FPM configuration registers.
73		- FMan controller configuration registers.
74
75- ranges
76		Usage: required
77		Value type: <prop-encoded-array>
78		Definition: A standard property.
79
80- clocks
81		Usage: required
82		Value type: <prop-encoded-array>
83		Definition: phandle for the fman input clock.
84
85- clock-names
86		usage: required
87		Value type: <stringlist>
88		Definition: "fmanclk" for the fman input clock.
89
90- interrupts
91		Usage: required
92		Value type: <prop-encoded-array>
93		Definition: A pair of IRQs are specified in this property.
94		The first element is associated with the event interrupts and
95		the second element is associated with the error interrupts.
96
97- fsl,qman-channel-range
98		Usage: required
99		Value type: <prop-encoded-array>
100		Definition: Specifies the range of the available dedicated
101		channels in the FMan. The first cell specifies the beginning
102		of the range and the second cell specifies the number of
103		channels.
104		Further information available at:
105		"Work Queue (WQ) Channel Assignments in the QMan" section
106		in DPAA Reference Manual.
107
108- fsl,qman
109- fsl,bman
110		Usage: required
111		Definition: See soc/fsl/qman.txt and soc/fsl/bman.txt
112
113=============================================================================
114FMan MURAM Node
115
116DESCRIPTION
117
118FMan Internal memory - shared between all the FMan modules.
119It contains data structures that are common and written to or read by
120the modules.
121FMan internal memory is split into the following parts:
122	Packet buffering (Tx/Rx FIFOs)
123	Frames internal context
124
125PROPERTIES
126
127- compatible
128		Usage: required
129		Value type: <stringlist>
130		Definition: Must include "fsl,fman-muram"
131
132- ranges
133		Usage: required
134		Value type: <prop-encoded-array>
135		Definition: A standard property.
136		Specifies the multi-user memory offset and the size within
137		the FMan.
138
139EXAMPLE
140
141muram@0 {
142	compatible = "fsl,fman-muram";
143	ranges = <0 0x000000 0x28000>;
144};
145
146=============================================================================
147FMan Port Node
148
149DESCRIPTION
150
151The Frame Manager (FMan) supports several types of hardware ports:
152	Ethernet receiver (RX)
153	Ethernet transmitter (TX)
154	Offline/Host command (O/H)
155
156PROPERTIES
157
158- compatible
159		Usage: required
160		Value type: <stringlist>
161		Definition: A standard property.
162		Must include one of the following:
163			- "fsl,fman-v2-port-oh" for FManV2 OH ports
164			- "fsl,fman-v2-port-rx" for FManV2 RX ports
165			- "fsl,fman-v2-port-tx" for FManV2 TX ports
166			- "fsl,fman-v3-port-oh" for FManV3 OH ports
167			- "fsl,fman-v3-port-rx" for FManV3 RX ports
168			- "fsl,fman-v3-port-tx" for FManV3 TX ports
169
170- cell-index
171		Usage: required
172		Value type: <u32>
173		Definition: Specifies the hardware port id.
174		Each hardware port on the FMan has its own hardware PortID.
175		Super set of all hardware Port IDs available at FMan Reference
176		Manual under "FMan Hardware Ports in Freescale Devices" table.
177
178		Each hardware port is assigned a 4KB, port-specific page in
179		the FMan hardware port memory region (which is part of the
180		FMan memory map). The first 4 KB in the FMan hardware ports
181		memory region is used for what are called common registers.
182		The subsequent 63 4KB pages are allocated to the hardware
183		ports.
184		The page of a specific port is determined by the cell-index.
185
186- reg
187		Usage: required
188		Value type: <prop-encoded-array>
189		Definition: There is one reg region describing the port
190		configuration registers.
191
192- fsl,fman-10g-port
193		Usage: optional
194		Value type: boolean
195		Definition: The default port rate is 1G.
196		If this property exists, the port is s 10G port.
197
198- fsl,fman-best-effort-port
199		Usage: optional
200		Value type: boolean
201		Definition: Can be defined only if 10G-support is set.
202		This property marks a best-effort 10G port (10G port that
203		may not be capable of line rate).
204
205EXAMPLE
206
207port@a8000 {
208	cell-index = <0x28>;
209	compatible = "fsl,fman-v2-port-tx";
210	reg = <0xa8000 0x1000>;
211};
212
213port@88000 {
214	cell-index = <0x8>;
215	compatible = "fsl,fman-v2-port-rx";
216	reg = <0x88000 0x1000>;
217};
218
219port@81000 {
220	cell-index = <0x1>;
221	compatible = "fsl,fman-v2-port-oh";
222	reg = <0x81000 0x1000>;
223};
224
225=============================================================================
226FMan dTSEC/XGEC/mEMAC Node
227
228DESCRIPTION
229
230mEMAC/dTSEC/XGEC are the Ethernet network interfaces
231
232PROPERTIES
233
234- compatible
235		Usage: required
236		Value type: <stringlist>
237		Definition: A standard property.
238		Must include one of the following:
239		- "fsl,fman-dtsec" for dTSEC MAC
240		- "fsl,fman-xgec" for XGEC MAC
241		- "fsl,fman-memac" for mEMAC MAC
242
243- cell-index
244		Usage: required
245		Value type: <u32>
246		Definition: Specifies the MAC id.
247
248		The cell-index value may be used by the FMan or the SoC, to
249		identify the MAC unit in the FMan (or SoC) memory map.
250		In the tables below there's a description of the cell-index
251		use, there are two tables, one describes the use of cell-index
252		by the FMan, the second describes the use by the SoC:
253
254		1. FMan Registers
255
256		FManV2:
257		register[bit]		MAC		cell-index
258		============================================================
259		FM_EPI[16]		XGEC		8
260		FM_EPI[16+n]		dTSECn		n-1
261		FM_NPI[11+n]		dTSECn		n-1
262			n = 1,..,5
263
264		FManV3:
265		register[bit]		MAC		cell-index
266		============================================================
267		FM_EPI[16+n]		mEMACn		n-1
268		FM_EPI[25]		mEMAC10		9
269
270		FM_NPI[11+n]		mEMACn		n-1
271		FM_NPI[10]		mEMAC10		9
272		FM_NPI[11]		mEMAC9		8
273			n = 1,..8
274
275		FM_EPI and FM_NPI are located in the FMan memory map.
276
277		2. SoC registers:
278
279		- P2041, P3041, P4080 P5020, P5040:
280		register[bit]		FMan		MAC		cell
281					Unit				index
282		============================================================
283		DCFG_DEVDISR2[7]	1		XGEC		8
284		DCFG_DEVDISR2[7+n]	1		dTSECn		n-1
285		DCFG_DEVDISR2[15]	2		XGEC		8
286		DCFG_DEVDISR2[15+n]	2		dTSECn		n-1
287			n = 1,..5
288
289		- T1040, T2080, T4240, B4860:
290		register[bit]			FMan	MAC		cell
291						Unit			index
292		============================================================
293		DCFG_CCSR_DEVDISR2[n-1]		1	mEMACn		n-1
294		DCFG_CCSR_DEVDISR2[11+n]	2	mEMACn		n-1
295			n = 1,..6,9,10
296
297		EVDISR, DCFG_DEVDISR2 and DCFG_CCSR_DEVDISR2 are located in
298		the specific SoC "Device Configuration/Pin Control" Memory
299		Map.
300
301- reg
302		Usage: required
303		Value type: <prop-encoded-array>
304		Definition: A standard property.
305
306- fsl,fman-ports
307		Usage: required
308		Value type: <prop-encoded-array>
309		Definition: An array of two phandles - the first references is
310		the FMan RX port and the second is the TX port used by this
311		MAC.
312
313- ptp-timer
314		Usage required
315		Value type: <phandle>
316		Definition: A phandle for 1EEE1588 timer.
317
318- pcsphy-handle
319		Usage required for "fsl,fman-memac" MACs
320		Value type: <phandle>
321		Definition: A phandle for pcsphy.
322
323- tbi-handle
324		Usage required for "fsl,fman-dtsec" MACs
325		Value type: <phandle>
326		Definition: A phandle for tbiphy.
327
328EXAMPLE
329
330fman1_tx28: port@a8000 {
331	cell-index = <0x28>;
332	compatible = "fsl,fman-v2-port-tx";
333	reg = <0xa8000 0x1000>;
334};
335
336fman1_rx8: port@88000 {
337	cell-index = <0x8>;
338	compatible = "fsl,fman-v2-port-rx";
339	reg = <0x88000 0x1000>;
340};
341
342ptp-timer: ptp_timer@fe000 {
343	compatible = "fsl,fman-ptp-timer";
344	reg = <0xfe000 0x1000>;
345};
346
347ethernet@e0000 {
348	compatible = "fsl,fman-dtsec";
349	cell-index = <0>;
350	reg = <0xe0000 0x1000>;
351	fsl,fman-ports = <&fman1_rx8 &fman1_tx28>;
352	ptp-timer = <&ptp-timer>;
353	tbi-handle = <&tbi0>;
354};
355
356============================================================================
357FMan IEEE 1588 Node
358
359Refer to Documentation/devicetree/bindings/ptp/ptp-qoriq.txt
360
361=============================================================================
362FMan MDIO Node
363
364DESCRIPTION
365
366The MDIO is a bus to which the PHY devices are connected.
367
368PROPERTIES
369
370- compatible
371		Usage: required
372		Value type: <stringlist>
373		Definition: A standard property.
374		Must include "fsl,fman-mdio" for 1 Gb/s MDIO from FMan v2.
375		Must include "fsl,fman-xmdio" for 10 Gb/s MDIO from FMan v2.
376		Must include "fsl,fman-memac-mdio" for 1/10 Gb/s MDIO from
377		FMan v3.
378
379- reg
380		Usage: required
381		Value type: <prop-encoded-array>
382		Definition: A standard property.
383
384- bus-frequency
385		Usage: optional
386		Value type: <u32>
387		Definition: Specifies the external MDIO bus clock speed to
388		be used, if different from the standard 2.5 MHz.
389		This may be due to the standard speed being unsupported (e.g.
390		due to a hardware problem), or to advertise that all relevant
391		components in the system support a faster speed.
392
393- interrupts
394		Usage: required for external MDIO
395		Value type: <prop-encoded-array>
396		Definition: Event interrupt of external MDIO controller.
397
398- fsl,fman-internal-mdio
399		Usage: required for internal MDIO
400		Value type: boolean
401		Definition: Fman has internal MDIO for internal PCS(Physical
402		Coding Sublayer) PHYs and external MDIO for external PHYs.
403		The settings and programming routines for internal/external
404		MDIO are different. Must be included for internal MDIO.
405
406For internal PHY device on internal mdio bus, a PHY node should be created.
407See the definition of the PHY node in booting-without-of.txt for an
408example of how to define a PHY (Internal PHY has no interrupt line).
409- For "fsl,fman-mdio" compatible internal mdio bus, the PHY is TBI PHY.
410- For "fsl,fman-memac-mdio" compatible internal mdio bus, the PHY is PCS PHY,
411  PCS PHY addr must be '0'.
412
413EXAMPLE
414
415Example for FMan v2 external MDIO:
416
417mdio@f1000 {
418	compatible = "fsl,fman-xmdio";
419	reg = <0xf1000 0x1000>;
420	interrupts = <101 2 0 0>;
421};
422
423Example for FMan v2 internal MDIO:
424
425mdio@e3120 {
426	compatible = "fsl,fman-mdio";
427	reg = <0xe3120 0xee0>;
428	fsl,fman-internal-mdio;
429
430	tbi1: tbi-phy@8 {
431		reg = <0x8>;
432		device_type = "tbi-phy";
433	};
434};
435
436Example for FMan v3 internal MDIO:
437
438mdio@f1000 {
439	compatible = "fsl,fman-memac-mdio";
440	reg = <0xf1000 0x1000>;
441	fsl,fman-internal-mdio;
442
443	pcsphy6: ethernet-phy@0 {
444		reg = <0x0>;
445	};
446};
447
448=============================================================================
449Example
450
451fman@400000 {
452	#address-cells = <1>;
453	#size-cells = <1>;
454	cell-index = <1>;
455	compatible = "fsl,fman"
456	ranges = <0 0x400000 0x100000>;
457	reg = <0x400000 0x100000>;
458	clocks = <&fman_clk>;
459	clock-names = "fmanclk";
460	interrupts = <
461		96 2 0 0
462		16 2 1 1>;
463	fsl,qman-channel-range = <0x40 0xc>;
464
465	muram@0 {
466		compatible = "fsl,fman-muram";
467		reg = <0x0 0x28000>;
468	};
469
470	port@81000 {
471		cell-index = <1>;
472		compatible = "fsl,fman-v2-port-oh";
473		reg = <0x81000 0x1000>;
474	};
475
476	port@82000 {
477		cell-index = <2>;
478		compatible = "fsl,fman-v2-port-oh";
479		reg = <0x82000 0x1000>;
480	};
481
482	port@83000 {
483		cell-index = <3>;
484		compatible = "fsl,fman-v2-port-oh";
485		reg = <0x83000 0x1000>;
486	};
487
488	port@84000 {
489		cell-index = <4>;
490		compatible = "fsl,fman-v2-port-oh";
491		reg = <0x84000 0x1000>;
492	};
493
494	port@85000 {
495		cell-index = <5>;
496		compatible = "fsl,fman-v2-port-oh";
497		reg = <0x85000 0x1000>;
498	};
499
500	port@86000 {
501		cell-index = <6>;
502		compatible = "fsl,fman-v2-port-oh";
503		reg = <0x86000 0x1000>;
504	};
505
506	fman1_rx_0x8: port@88000 {
507		cell-index = <0x8>;
508		compatible = "fsl,fman-v2-port-rx";
509		reg = <0x88000 0x1000>;
510	};
511
512	fman1_rx_0x9: port@89000 {
513		cell-index = <0x9>;
514		compatible = "fsl,fman-v2-port-rx";
515		reg = <0x89000 0x1000>;
516	};
517
518	fman1_rx_0xa: port@8a000 {
519		cell-index = <0xa>;
520		compatible = "fsl,fman-v2-port-rx";
521		reg = <0x8a000 0x1000>;
522	};
523
524	fman1_rx_0xb: port@8b000 {
525		cell-index = <0xb>;
526		compatible = "fsl,fman-v2-port-rx";
527		reg = <0x8b000 0x1000>;
528	};
529
530	fman1_rx_0xc: port@8c000 {
531		cell-index = <0xc>;
532		compatible = "fsl,fman-v2-port-rx";
533		reg = <0x8c000 0x1000>;
534	};
535
536	fman1_rx_0x10: port@90000 {
537		cell-index = <0x10>;
538		compatible = "fsl,fman-v2-port-rx";
539		reg = <0x90000 0x1000>;
540	};
541
542	fman1_tx_0x28: port@a8000 {
543		cell-index = <0x28>;
544		compatible = "fsl,fman-v2-port-tx";
545		reg = <0xa8000 0x1000>;
546	};
547
548	fman1_tx_0x29: port@a9000 {
549		cell-index = <0x29>;
550		compatible = "fsl,fman-v2-port-tx";
551		reg = <0xa9000 0x1000>;
552	};
553
554	fman1_tx_0x2a: port@aa000 {
555		cell-index = <0x2a>;
556		compatible = "fsl,fman-v2-port-tx";
557		reg = <0xaa000 0x1000>;
558	};
559
560	fman1_tx_0x2b: port@ab000 {
561		cell-index = <0x2b>;
562		compatible = "fsl,fman-v2-port-tx";
563		reg = <0xab000 0x1000>;
564	};
565
566	fman1_tx_0x2c: port@ac0000 {
567		cell-index = <0x2c>;
568		compatible = "fsl,fman-v2-port-tx";
569		reg = <0xac000 0x1000>;
570	};
571
572	fman1_tx_0x30: port@b0000 {
573		cell-index = <0x30>;
574		compatible = "fsl,fman-v2-port-tx";
575		reg = <0xb0000 0x1000>;
576	};
577
578	ethernet@e0000 {
579		compatible = "fsl,fman-dtsec";
580		cell-index = <0>;
581		reg = <0xe0000 0x1000>;
582		fsl,fman-ports = <&fman1_rx_0x8 &fman1_tx_0x28>;
583		tbi-handle = <&tbi5>;
584	};
585
586	ethernet@e2000 {
587		compatible = "fsl,fman-dtsec";
588		cell-index = <1>;
589		reg = <0xe2000 0x1000>;
590		fsl,fman-ports = <&fman1_rx_0x9 &fman1_tx_0x29>;
591		tbi-handle = <&tbi6>;
592	};
593
594	ethernet@e4000 {
595		compatible = "fsl,fman-dtsec";
596		cell-index = <2>;
597		reg = <0xe4000 0x1000>;
598		fsl,fman-ports = <&fman1_rx_0xa &fman1_tx_0x2a>;
599		tbi-handle = <&tbi7>;
600	};
601
602	ethernet@e6000 {
603		compatible = "fsl,fman-dtsec";
604		cell-index = <3>;
605		reg = <0xe6000 0x1000>;
606		fsl,fman-ports = <&fman1_rx_0xb &fman1_tx_0x2b>;
607		tbi-handle = <&tbi8>;
608	};
609
610	ethernet@e8000 {
611		compatible = "fsl,fman-dtsec";
612		cell-index = <4>;
613		reg = <0xf0000 0x1000>;
614		fsl,fman-ports = <&fman1_rx_0xc &fman1_tx_0x2c>;
615		tbi-handle = <&tbi9>;
616
617	ethernet@f0000 {
618		cell-index = <8>;
619		compatible = "fsl,fman-xgec";
620		reg = <0xf0000 0x1000>;
621		fsl,fman-ports = <&fman1_rx_0x10 &fman1_tx_0x30>;
622	};
623
624	ptp-timer@fe000 {
625		compatible = "fsl,fman-ptp-timer";
626		reg = <0xfe000 0x1000>;
627	};
628
629	mdio@f1000 {
630		compatible = "fsl,fman-xmdio";
631		reg = <0xf1000 0x1000>;
632		interrupts = <101 2 0 0>;
633	};
634};
635