1* ENETC ethernet device tree bindings
2
3Depending on board design and ENETC port type (internal or
4external) there are two supported link modes specified by
5below device tree bindings.
6
7Required properties:
8
9- reg		: Specifies PCIe Device Number and Function
10		  Number of the ENETC endpoint device, according
11		  to parent node bindings.
12- compatible	: Should be "fsl,enetc".
13
141. The ENETC external port is connected to a MDIO configurable phy
15
161.1. Using the local ENETC Port MDIO interface
17
18In this case, the ENETC node should include a "mdio" sub-node
19that in turn should contain the "ethernet-phy" node describing the
20external phy.  Below properties are required, their bindings
21already defined in Documentation/devicetree/bindings/net/ethernet.txt or
22Documentation/devicetree/bindings/net/phy.txt.
23
24Required:
25
26- phy-handle		: Phandle to a PHY on the MDIO bus.
27			  Defined in ethernet.txt.
28
29- phy-connection-type	: Defined in ethernet.txt.
30
31- mdio			: "mdio" node, defined in mdio.txt.
32
33- ethernet-phy		: "ethernet-phy" node, defined in phy.txt.
34
35Example:
36
37	ethernet@0,0 {
38		compatible = "fsl,enetc";
39		reg = <0x000000 0 0 0 0>;
40		phy-handle = <&sgmii_phy0>;
41		phy-connection-type = "sgmii";
42
43		mdio {
44			#address-cells = <1>;
45			#size-cells = <0>;
46			sgmii_phy0: ethernet-phy@2 {
47				reg = <0x2>;
48			};
49		};
50	};
51
521.2. Using the central MDIO PCIe endpoint device
53
54In this case, the mdio node should be defined as another PCIe
55endpoint node, at the same level with the ENETC port nodes.
56
57Required properties:
58
59- reg		: Specifies PCIe Device Number and Function
60		  Number of the ENETC endpoint device, according
61		  to parent node bindings.
62- compatible	: Should be "fsl,enetc-mdio".
63
64The remaining required mdio bus properties are standard, their bindings
65already defined in Documentation/devicetree/bindings/net/mdio.txt.
66
67Example:
68
69	ethernet@0,0 {
70		compatible = "fsl,enetc";
71		reg = <0x000000 0 0 0 0>;
72		phy-handle = <&sgmii_phy0>;
73		phy-connection-type = "sgmii";
74	};
75
76	mdio@0,3 {
77		compatible = "fsl,enetc-mdio";
78		reg = <0x000300 0 0 0 0>;
79		#address-cells = <1>;
80		#size-cells = <0>;
81		sgmii_phy0: ethernet-phy@2 {
82			reg = <0x2>;
83		};
84	};
85
862. The ENETC port is an internal port or has a fixed-link external
87connection
88
89In this case, the ENETC port node defines a fixed link connection,
90as specified by Documentation/devicetree/bindings/net/fixed-link.txt.
91
92Required:
93
94- fixed-link	: "fixed-link" node, defined in "fixed-link.txt".
95
96Example:
97	ethernet@0,2 {
98		compatible = "fsl,enetc";
99		reg = <0x000200 0 0 0 0>;
100		fixed-link {
101			speed = <1000>;
102			full-duplex;
103		};
104	};
105
106* Integrated Endpoint Register Block bindings
107
108Optionally, the fsl_enetc driver can probe on the Integrated Endpoint Register
109Block, which preconfigures the FIFO limits for the ENETC ports. This is a node
110with the following properties:
111
112- reg		: Specifies the address in the SoC memory space.
113- compatible	: Must be "fsl,ls1028a-enetc-ierb".
114
115Example:
116	ierb@1f0800000 {
117		compatible = "fsl,ls1028a-enetc-ierb";
118		reg = <0x01 0xf0800000 0x0 0x10000>;
119	};
120