1APM X-Gene SoC Ethernet nodes
2
3Ethernet nodes are defined to describe on-chip ethernet interfaces in
4APM X-Gene SoC.
5
6Required properties for all the ethernet interfaces:
7- compatible: Should state binding information from the following list,
8  - "apm,xgene-enet":    RGMII based 1G interface
9  - "apm,xgene1-sgenet": SGMII based 1G interface
10  - "apm,xgene1-xgenet": XFI based 10G interface
11- reg: Address and length of the register set for the device. It contains the
12  information of registers in the same order as described by reg-names
13- reg-names: Should contain the register set names
14  - "enet_csr": Ethernet control and status register address space
15  - "ring_csr": Descriptor ring control and status register address space
16  - "ring_cmd": Descriptor ring command register address space
17- interrupts: Two interrupt specifiers can be specified.
18  - First is the Rx interrupt.  This irq is mandatory.
19  - Second is the Tx completion interrupt.
20    This is supported only on SGMII based 1GbE and 10GbE interfaces.
21- channel: Ethernet to CPU, start channel (prefetch buffer) number
22  - Must map to the first irq and irqs must be sequential
23- port-id: Port number (0 or 1)
24- clocks: Reference to the clock entry.
25- local-mac-address: MAC address assigned to this device
26- phy-connection-type: Interface type between ethernet device and PHY device
27
28Required properties for ethernet interfaces that have external PHY:
29- phy-handle: Reference to a PHY node connected to this device
30
31- mdio: Device tree subnode with the following required properties:
32  - compatible: Must be "apm,xgene-mdio".
33  - #address-cells: Must be <1>.
34  - #size-cells: Must be <0>.
35
36  For the phy on the mdio bus, there must be a node with the following fields:
37  - compatible: PHY identifier.  Please refer ./phy.txt for the format.
38  - reg: The ID number for the phy.
39
40Optional properties:
41- status: Should be "ok" or "disabled" for enabled/disabled. Default is "ok".
42- tx-delay: Delay value for RGMII bridge TX clock.
43	    Valid values are between 0 to 7, that maps to
44	    417, 717, 1020, 1321, 1611, 1913, 2215, 2514 ps
45	    Default value is 4, which corresponds to 1611 ps
46- rx-delay: Delay value for RGMII bridge RX clock.
47	    Valid values are between 0 to 7, that maps to
48	    273, 589, 899, 1222, 1480, 1806, 2147, 2464 ps
49	    Default value is 2, which corresponds to 899 ps
50- rxlos-gpios: Input gpio from SFP+ module to indicate availability of
51	       incoming signal.
52
53
54Example:
55	menetclk: menetclk {
56		compatible = "apm,xgene-device-clock";
57		clock-output-names = "menetclk";
58		status = "ok";
59	};
60
61	menet: ethernet@17020000 {
62		compatible = "apm,xgene-enet";
63		status = "disabled";
64		reg = <0x0 0x17020000 0x0 0xd100>,
65		      <0x0 0x17030000 0x0 0x400>,
66		      <0x0 0x10000000 0x0 0x200>;
67		reg-names = "enet_csr", "ring_csr", "ring_cmd";
68		interrupts = <0x0 0x3c 0x4>;
69		port-id = <0>;
70		clocks = <&menetclk 0>;
71		local-mac-address = [00 01 73 00 00 01];
72		phy-connection-type = "rgmii";
73		phy-handle = <&menetphy>;
74		mdio {
75			compatible = "apm,xgene-mdio";
76			#address-cells = <1>;
77			#size-cells = <0>;
78			menetphy: menetphy@3 {
79				compatible = "ethernet-phy-id001c.c915";
80				reg = <0x3>;
81			};
82
83		};
84	};
85
86/* Board-specific peripheral configurations */
87&menet {
88	tx-delay = <4>;
89	rx-delay = <2>;
90        status = "ok";
91};
92