1# SPDX-License-Identifier: GPL-2.0
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/mtd/nand-controller.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: NAND Controller Common Properties
8
9maintainers:
10  - Miquel Raynal <miquel.raynal@bootlin.com>
11  - Richard Weinberger <richard@nod.at>
12
13description: |
14  The NAND controller should be represented with its own DT node, and
15  all NAND chips attached to this controller should be defined as
16  children nodes of the NAND controller. This representation should be
17  enforced even for simple controllers supporting only one chip.
18
19  The ECC strength and ECC step size properties define the user
20  desires in terms of correction capability of a controller. Together,
21  they request the ECC engine to correct {strength} bit errors per
22  {size} bytes.
23
24  The interpretation of these parameters is implementation-defined, so
25  not all implementations must support all possible
26  combinations. However, implementations are encouraged to further
27  specify the value(s) they support.
28
29properties:
30  $nodename:
31    pattern: "^nand-controller(@.*)?"
32
33  "#address-cells":
34    const: 1
35
36  "#size-cells":
37    const: 0
38
39  ranges: true
40
41  cs-gpios:
42    description:
43      Array of chip-select available to the controller. The first
44      entries are a 1:1 mapping of the available chip-select on the
45      NAND controller (even if they are not used). As many additional
46      chip-select as needed may follow and should be phandles of GPIO
47      lines. 'reg' entries of the NAND chip subnodes become indexes of
48      this array when this property is present.
49    minItems: 1
50    maxItems: 8
51
52patternProperties:
53  "^nand@[a-f0-9]$":
54    $ref: nand-chip.yaml#
55
56    properties:
57      reg:
58        description:
59          Contains the chip-select IDs.
60
61      nand-ecc-placement:
62        description:
63          Location of the ECC bytes. This location is unknown by default
64          but can be explicitly set to "oob", if all ECC bytes are
65          known to be stored in the OOB area, or "interleaved" if ECC
66          bytes will be interleaved with regular data in the main area.
67        $ref: /schemas/types.yaml#/definitions/string
68        enum: [ oob, interleaved ]
69
70      nand-bus-width:
71        description:
72          Bus width to the NAND chip
73        $ref: /schemas/types.yaml#/definitions/uint32
74        enum: [8, 16]
75        default: 8
76
77      nand-on-flash-bbt:
78        description:
79          With this property, the OS will search the device for a Bad
80          Block Table (BBT). If not found, it will create one, reserve
81          a few blocks at the end of the device to store it and update
82          it as the device ages. Otherwise, the out-of-band area of a
83          few pages of all the blocks will be scanned at boot time to
84          find Bad Block Markers (BBM). These markers will help to
85          build a volatile BBT in RAM.
86        $ref: /schemas/types.yaml#/definitions/flag
87
88      nand-ecc-maximize:
89        description:
90          Whether or not the ECC strength should be maximized. The
91          maximum ECC strength is both controller and chip
92          dependent. The ECC engine has to select the ECC config
93          providing the best strength and taking the OOB area size
94          constraint into account. This is particularly useful when
95          only the in-band area is used by the upper layers, and you
96          want to make your NAND as reliable as possible.
97        $ref: /schemas/types.yaml#/definitions/flag
98
99      nand-is-boot-medium:
100        description:
101          Whether or not the NAND chip is a boot medium. Drivers might
102          use this information to select ECC algorithms supported by
103          the boot ROM or similar restrictions.
104        $ref: /schemas/types.yaml#/definitions/flag
105
106      nand-rb:
107        description:
108          Contains the native Ready/Busy IDs.
109        $ref: /schemas/types.yaml#/definitions/uint32-array
110
111      rb-gpios:
112        description:
113          Contains one or more GPIO descriptor (the numper of descriptor
114          depends on the number of R/B pins exposed by the flash) for the
115          Ready/Busy pins. Active state refers to the NAND ready state and
116          should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted.
117
118      wp-gpios:
119        description:
120          Contains one GPIO descriptor for the Write Protect pin.
121          Active state refers to the NAND Write Protect state and should be
122          set to GPIOD_ACTIVE_LOW unless the signal is inverted.
123        maxItems: 1
124
125    required:
126      - reg
127
128required:
129  - "#address-cells"
130  - "#size-cells"
131
132# This is a generic file other binding inherit from and extend
133additionalProperties: true
134
135examples:
136  - |
137    nand-controller {
138      #address-cells = <1>;
139      #size-cells = <0>;
140      cs-gpios = <0>, <&gpioA 1>; /* A single native CS is available */
141
142      /* controller specific properties */
143
144      nand@0 {
145        reg = <0>; /* Native CS */
146        /* NAND chip specific properties */
147      };
148
149      nand@1 {
150        reg = <1>; /* GPIO CS */
151      };
152    };
153