1# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/gpio/xlnx,gpio-xilinx.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Xilinx AXI GPIO controller
8
9maintainers:
10  - Neeli Srinivas <srinivas.neeli@amd.com>
11
12description:
13  The AXI GPIO design provides a general purpose input/output interface
14  to an AXI4-Lite interface. The AXI GPIO can be configured as either
15  a single or a dual-channel device. The width of each channel is
16  independently configurable. The channels can be configured to
17  generate an interrupt when a transition on any of their inputs occurs.
18
19properties:
20  compatible:
21    enum:
22      - xlnx,xps-gpio-1.00.a
23
24  reg:
25    maxItems: 1
26
27  "#gpio-cells":
28    const: 2
29
30  interrupts:
31    maxItems: 1
32
33  gpio-controller: true
34
35  gpio-line-names:
36    description: strings describing the names of each gpio line
37    minItems: 1
38    maxItems: 64
39
40  interrupt-controller: true
41
42  "#interrupt-cells":
43    const: 2
44
45  clocks:
46    maxItems: 1
47
48  interrupt-names: true
49
50  xlnx,all-inputs:
51    $ref: /schemas/types.yaml#/definitions/uint32
52    description: This option sets this GPIO channel1 bits in input mode.
53
54  xlnx,all-inputs-2:
55    $ref: /schemas/types.yaml#/definitions/uint32
56    description: This option sets this GPIO channel2 bits in input mode.
57
58  xlnx,all-outputs:
59    $ref: /schemas/types.yaml#/definitions/uint32
60    description: This option sets this GPIO channel1 bits in output mode.
61
62  xlnx,all-outputs-2:
63    $ref: /schemas/types.yaml#/definitions/uint32
64    description: This option sets this GPIO channel2 bits in output mode.
65
66  xlnx,dout-default:
67    $ref: /schemas/types.yaml#/definitions/uint32
68    description: Sets the default value of all the enabled bits of
69                 channel1.
70    default: 0
71
72  xlnx,dout-default-2:
73    $ref: /schemas/types.yaml#/definitions/uint32
74    description: Sets the default value of all the enabled bits of
75                 channel2.
76    default: 0
77
78  xlnx,gpio-width:
79    $ref: /schemas/types.yaml#/definitions/uint32
80    description: The value defines the bit width of the GPIO channel1.
81    minimum: 1
82    maximum: 32
83    default: 32
84
85  xlnx,gpio2-width:
86    $ref: /schemas/types.yaml#/definitions/uint32
87    description: The value defines the bit width of the GPIO channel2.
88    minimum: 1
89    maximum: 32
90    default: 32
91
92  xlnx,interrupt-present:
93    $ref: /schemas/types.yaml#/definitions/uint32
94    description: This parameter enables interrupt control logic
95                 and interrupt registers in GPIO module.
96    minimum: 0
97    maximum: 1
98    default: 0
99
100  xlnx,is-dual:
101    $ref: /schemas/types.yaml#/definitions/uint32
102    description: This parameter enables a second GPIO channel (GPIO2).
103    minimum: 0
104    maximum: 1
105    default: 0
106
107  xlnx,tri-default:
108    $ref: /schemas/types.yaml#/definitions/uint32
109    description: This value configures the input or output mode
110                 of each bit of GPIO channel1.
111
112  xlnx,tri-default-2:
113    $ref: /schemas/types.yaml#/definitions/uint32
114    description: This value configures the input or output mode
115                 of each bit of GPIO channel2.
116
117required:
118  - reg
119  - compatible
120  - gpio-controller
121  - "#gpio-cells"
122
123unevaluatedProperties: false
124
125examples:
126  - |
127    #include <dt-bindings/interrupt-controller/arm-gic.h>
128
129        gpio@e000a000 {
130            compatible = "xlnx,xps-gpio-1.00.a";
131            reg = <0xa0020000 0x10000>;
132            #gpio-cells = <2>;
133            #interrupt-cells = <0x2>;
134            clocks = <&zynqmp_clk 71>;
135            gpio-controller;
136            interrupt-controller;
137            interrupt-names = "ip2intc_irpt";
138            interrupt-parent = <&gic>;
139            interrupts = <0 89 4>;
140            xlnx,all-inputs = <0x0>;
141            xlnx,all-inputs-2 = <0x0>;
142            xlnx,all-outputs = <0x0>;
143            xlnx,all-outputs-2 = <0x0>;
144            xlnx,dout-default = <0x0>;
145            xlnx,dout-default-2 = <0x0>;
146            xlnx,gpio-width = <0x20>;
147            xlnx,gpio2-width = <0x20>;
148            xlnx,interrupt-present = <0x1>;
149            xlnx,is-dual = <0x1>;
150            xlnx,tri-default = <0xFFFFFFFF>;
151            xlnx,tri-default-2 = <0xFFFFFFFF>;
152        };
153
154...
155