1Specifying GPIO information for devices 2============================================ 3 41) gpios property 5----------------- 6 7Nodes that makes use of GPIOs should specify them using one or more 8properties, each containing a 'gpio-list': 9 10 gpio-list ::= <single-gpio> [gpio-list] 11 single-gpio ::= <gpio-phandle> <gpio-specifier> 12 gpio-phandle : phandle to gpio controller node 13 gpio-specifier : Array of #gpio-cells specifying specific gpio 14 (controller specific) 15 16GPIO properties should be named "[<name>-]gpios", with <name> being the purpose 17of this GPIO for the device. While a non-existent <name> is considered valid 18for compatibility reasons (resolving to the "gpios" property), it is not allowed 19for new bindings. Also, GPIO properties named "[<name>-]gpio" are valid and old 20bindings use it, but are only supported for compatibility reasons and should not 21be used for newer bindings since it has been deprecated. 22 23GPIO properties can contain one or more GPIO phandles, but only in exceptional 24cases should they contain more than one. If your device uses several GPIOs with 25distinct functions, reference each of them under its own property, giving it a 26meaningful name. The only case where an array of GPIOs is accepted is when 27several GPIOs serve the same function (e.g. a parallel data line). 28 29The exact purpose of each gpios property must be documented in the device tree 30binding of the device. 31 32The following example could be used to describe GPIO pins used as device enable 33and bit-banged data signals: 34 35 gpio1: gpio1 { 36 gpio-controller 37 #gpio-cells = <2>; 38 }; 39 gpio2: gpio2 { 40 gpio-controller 41 #gpio-cells = <1>; 42 }; 43 [...] 44 45 enable-gpios = <&gpio2 2>; 46 data-gpios = <&gpio1 12 0>, 47 <&gpio1 13 0>, 48 <&gpio1 14 0>, 49 <&gpio1 15 0>; 50 51Note that gpio-specifier length is controller dependent. In the 52above example, &gpio1 uses 2 cells to specify a gpio, while &gpio2 53only uses one. 54 55gpio-specifier may encode: bank, pin position inside the bank, 56whether pin is open-drain and whether pin is logically inverted. 57 58Exact meaning of each specifier cell is controller specific, and must 59be documented in the device tree binding for the device. 60 61Most controllers are however specifying a generic flag bitfield 62in the last cell, so for these, use the macros defined in 63include/dt-bindings/gpio/gpio.h whenever possible: 64 65Example of a node using GPIOs: 66 67 node { 68 enable-gpios = <&qe_pio_e 18 GPIO_ACTIVE_HIGH>; 69 }; 70 71GPIO_ACTIVE_HIGH is 0, so in this example gpio-specifier is "18 0" and encodes 72GPIO pin number, and GPIO flags as accepted by the "qe_pio_e" gpio-controller. 73 74Optional standard bitfield specifiers for the last cell: 75 76- Bit 0: 0 means active high, 1 means active low 77- Bit 1: 1 means single-ended wiring, see: 78 https://en.wikipedia.org/wiki/Single-ended_triode 79 When used with active-low, this means open drain/collector, see: 80 https://en.wikipedia.org/wiki/Open_collector 81 When used with active-high, this means open source/emitter 82 831.1) GPIO specifier best practices 84---------------------------------- 85 86A gpio-specifier should contain a flag indicating the GPIO polarity; active- 87high or active-low. If it does, the following best practices should be 88followed: 89 90The gpio-specifier's polarity flag should represent the physical level at the 91GPIO controller that achieves (or represents, for inputs) a logically asserted 92value at the device. The exact definition of logically asserted should be 93defined by the binding for the device. If the board inverts the signal between 94the GPIO controller and the device, then the gpio-specifier will represent the 95opposite physical level than the signal at the device's pin. 96 97When the device's signal polarity is configurable, the binding for the 98device must either: 99 100a) Define a single static polarity for the signal, with the expectation that 101any software using that binding would statically program the device to use 102that signal polarity. 103 104The static choice of polarity may be either: 105 106a1) (Preferred) Dictated by a binding-specific DT property. 107 108or: 109 110a2) Defined statically by the DT binding itself. 111 112In particular, the polarity cannot be derived from the gpio-specifier, since 113that would prevent the DT from separately representing the two orthogonal 114concepts of configurable signal polarity in the device, and possible board- 115level signal inversion. 116 117or: 118 119b) Pick a single option for device signal polarity, and document this choice 120in the binding. The gpio-specifier should represent the polarity of the signal 121(at the GPIO controller) assuming that the device is configured for this 122particular signal polarity choice. If software chooses to program the device 123to generate or receive a signal of the opposite polarity, software will be 124responsible for correctly interpreting (inverting) the GPIO signal at the GPIO 125controller. 126 1272) gpio-controller nodes 128------------------------ 129 130Every GPIO controller node must contain both an empty "gpio-controller" 131property, and a #gpio-cells integer property, which indicates the number of 132cells in a gpio-specifier. 133 134Optionally, a GPIO controller may have a "ngpios" property. This property 135indicates the number of in-use slots of available slots for GPIOs. The 136typical example is something like this: the hardware register is 32 bits 137wide, but only 18 of the bits have a physical counterpart. The driver is 138generally written so that all 32 bits can be used, but the IP block is reused 139in a lot of designs, some using all 32 bits, some using 18 and some using 14012. In this case, setting "ngpios = <18>;" informs the driver that only the 141first 18 GPIOs, at local offset 0 .. 17, are in use. 142 143If these GPIOs do not happen to be the first N GPIOs at offset 0...N-1, an 144additional bitmask is needed to specify which GPIOs are actually in use, 145and which are dummies. The bindings for this case has not yet been 146specified, but should be specified if/when such hardware appears. 147 148Example: 149 150gpio-controller@00000000 { 151 compatible = "foo"; 152 reg = <0x00000000 0x1000>; 153 gpio-controller; 154 #gpio-cells = <2>; 155 ngpios = <18>; 156} 157 158The GPIO chip may contain GPIO hog definitions. GPIO hogging is a mechanism 159providing automatic GPIO request and configuration as part of the 160gpio-controller's driver probe function. 161 162Each GPIO hog definition is represented as a child node of the GPIO controller. 163Required properties: 164- gpio-hog: A property specifying that this child node represent a GPIO hog. 165- gpios: Store the GPIO information (id, flags, ...). Shall contain the 166 number of cells specified in its parent node (GPIO controller 167 node). 168Only one of the following properties scanned in the order shown below. 169This means that when multiple properties are present they will be searched 170in the order presented below and the first match is taken as the intended 171configuration. 172- input: A property specifying to set the GPIO direction as input. 173- output-low A property specifying to set the GPIO direction as output with 174 the value low. 175- output-high A property specifying to set the GPIO direction as output with 176 the value high. 177 178Optional properties: 179- line-name: The GPIO label name. If not present the node name is used. 180 181Example of two SOC GPIO banks defined as gpio-controller nodes: 182 183 qe_pio_a: gpio-controller@1400 { 184 compatible = "fsl,qe-pario-bank-a", "fsl,qe-pario-bank"; 185 reg = <0x1400 0x18>; 186 gpio-controller; 187 #gpio-cells = <2>; 188 189 line_b { 190 gpio-hog; 191 gpios = <6 0>; 192 output-low; 193 line-name = "foo-bar-gpio"; 194 }; 195 }; 196 197 qe_pio_e: gpio-controller@1460 { 198 compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; 199 reg = <0x1460 0x18>; 200 gpio-controller; 201 #gpio-cells = <2>; 202 }; 203 2042.1) gpio- and pin-controller interaction 205----------------------------------------- 206 207Some or all of the GPIOs provided by a GPIO controller may be routed to pins 208on the package via a pin controller. This allows muxing those pins between 209GPIO and other functions. 210 211It is useful to represent which GPIOs correspond to which pins on which pin 212controllers. The gpio-ranges property described below represents this, and 213contains information structures as follows: 214 215 gpio-range-list ::= <single-gpio-range> [gpio-range-list] 216 single-gpio-range ::= <numeric-gpio-range> | <named-gpio-range> 217 numeric-gpio-range ::= 218 <pinctrl-phandle> <gpio-base> <pinctrl-base> <count> 219 named-gpio-range ::= <pinctrl-phandle> <gpio-base> '<0 0>' 220 pinctrl-phandle : phandle to pin controller node 221 gpio-base : Base GPIO ID in the GPIO controller 222 pinctrl-base : Base pinctrl pin ID in the pin controller 223 count : The number of GPIOs/pins in this range 224 225The "pin controller node" mentioned above must conform to the bindings 226described in ../pinctrl/pinctrl-bindings.txt. 227 228In case named gpio ranges are used (ranges with both <pinctrl-base> and 229<count> set to 0), the property gpio-ranges-group-names contains one string 230for every single-gpio-range in gpio-ranges: 231 gpiorange-names-list ::= <gpiorange-name> [gpiorange-names-list] 232 gpiorange-name : Name of the pingroup associated to the GPIO range in 233 the respective pin controller. 234 235Elements of gpiorange-names-list corresponding to numeric ranges contain 236the empty string. Elements of gpiorange-names-list corresponding to named 237ranges contain the name of a pin group defined in the respective pin 238controller. The number of pins/GPIOs in the range is the number of pins in 239that pin group. 240 241Previous versions of this binding required all pin controller nodes that 242were referenced by any gpio-ranges property to contain a property named 243#gpio-range-cells with value <3>. This requirement is now deprecated. 244However, that property may still exist in older device trees for 245compatibility reasons, and would still be required even in new device 246trees that need to be compatible with older software. 247 248Example 1: 249 250 qe_pio_e: gpio-controller@1460 { 251 #gpio-cells = <2>; 252 compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; 253 reg = <0x1460 0x18>; 254 gpio-controller; 255 gpio-ranges = <&pinctrl1 0 20 10>, <&pinctrl2 10 50 20>; 256 }; 257 258Here, a single GPIO controller has GPIOs 0..9 routed to pin controller 259pinctrl1's pins 20..29, and GPIOs 10..19 routed to pin controller pinctrl2's 260pins 50..59. 261 262Example 2: 263 264 gpio_pio_i: gpio-controller@14B0 { 265 #gpio-cells = <2>; 266 compatible = "fsl,qe-pario-bank-e", "fsl,qe-pario-bank"; 267 reg = <0x1480 0x18>; 268 gpio-controller; 269 gpio-ranges = <&pinctrl1 0 20 10>, 270 <&pinctrl2 10 0 0>, 271 <&pinctrl1 15 0 10>, 272 <&pinctrl2 25 0 0>; 273 gpio-ranges-group-names = "", 274 "foo", 275 "", 276 "bar"; 277 }; 278 279Here, three GPIO ranges are defined wrt. two pin controllers. pinctrl1 GPIO 280ranges are defined using pin numbers whereas the GPIO ranges wrt. pinctrl2 281are named "foo" and "bar". 282