1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: Binding for IDT VersaClock 5 and 6 programmable I2C clock generators
8
9description: |
10  The IDT VersaClock 5 and VersaClock 6 are programmable I2C
11  clock generators providing from 3 to 12 output clocks.
12
13  When referencing the provided clock in the DT using phandle and clock
14  specifier, the following mapping applies:
15
16  - 5P49V5923:
17    0 -- OUT0_SEL_I2CB
18    1 -- OUT1
19    2 -- OUT2
20
21  - 5P49V5933:
22    0 -- OUT0_SEL_I2CB
23    1 -- OUT1
24    2 -- OUT4
25
26  - other parts:
27    0 -- OUT0_SEL_I2CB
28    1 -- OUT1
29    2 -- OUT2
30    3 -- OUT3
31    4 -- OUT4
32
33  The idt,shutdown and idt,output-enable-active properties control the
34  SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown
35  Register, respectively. Their behavior is summarized by the following
36  table:
37
38  SH SP Output when the SD/OE pin is Low/High
39  == == =====================================
40   0  0 Active/Inactive
41   0  1 Inactive/Active
42   1  0 Active/Shutdown
43   1  1 Inactive/Shutdown
44
45  The case where SH and SP are both 1 is likely not very interesting.
46
47maintainers:
48  - Luca Ceresoli <luca@lucaceresoli.net>
49
50properties:
51  compatible:
52    enum:
53      - idt,5p49v5923
54      - idt,5p49v5925
55      - idt,5p49v5933
56      - idt,5p49v5935
57      - idt,5p49v6901
58      - idt,5p49v6965
59
60  reg:
61    description: I2C device address
62    enum: [ 0x68, 0x6a ]
63
64  '#clock-cells':
65    const: 1
66
67  clock-names:
68    minItems: 1
69    maxItems: 2
70    items:
71      enum: [ xin, clkin ]
72  clocks:
73    minItems: 1
74    maxItems: 2
75
76  idt,xtal-load-femtofarads:
77    minimum: 9000
78    maximum: 22760
79    description: Optional load capacitor for XTAL1 and XTAL2
80
81  idt,shutdown:
82    $ref: /schemas/types.yaml#/definitions/uint32
83    enum: [0, 1]
84    description: |
85      If 1, this enables the shutdown functionality: the chip will be
86      shut down if the SD/OE pin is driven high. If 0, this disables the
87      shutdown functionality: the chip will never be shut down based on
88      the value of the SD/OE pin. This property corresponds to the SH
89      bit of the Primary Source and Shutdown Register.
90
91  idt,output-enable-active:
92    $ref: /schemas/types.yaml#/definitions/uint32
93    enum: [0, 1]
94    description: |
95      If 1, this enables output when the SD/OE pin is high, and disables
96      output when the SD/OE pin is low. If 0, this disables output when
97      the SD/OE pin is high, and enables output when the SD/OE pin is
98      low. This corresponds to the SP bit of the Primary Source and
99      Shutdown Register.
100
101patternProperties:
102  "^OUT[1-4]$":
103    type: object
104    description:
105      Description of one of the outputs (OUT1..OUT4). See "Clock1 Output
106      Configuration" in the Versaclock 5/6/6E Family Register Description
107      and Programming Guide.
108    properties:
109      idt,mode:
110        description:
111          The output drive mode. Values defined in dt-bindings/clk/versaclock.h
112        $ref: /schemas/types.yaml#/definitions/uint32
113        minimum: 0
114        maximum: 6
115      idt,voltage-microvolt:
116        description: The output drive voltage.
117        enum: [ 1800000, 2500000, 3300000 ]
118      idt,slew-percent:
119        description: The Slew rate control for CMOS single-ended.
120        enum: [ 80, 85, 90, 100 ]
121    additionalProperties: false
122
123required:
124  - compatible
125  - reg
126  - '#clock-cells'
127  - idt,shutdown
128  - idt,output-enable-active
129
130allOf:
131  - if:
132      properties:
133        compatible:
134          enum:
135            - idt,5p49v5933
136            - idt,5p49v5935
137    then:
138      # Devices with builtin crystal + optional external input
139      properties:
140        clock-names:
141          const: clkin
142        clocks:
143          maxItems: 1
144    else:
145      # Devices without builtin crystal
146      required:
147        - clock-names
148        - clocks
149
150additionalProperties: false
151
152examples:
153  - |
154    #include <dt-bindings/clk/versaclock.h>
155
156    /* 25MHz reference crystal */
157    ref25: ref25m {
158        compatible = "fixed-clock";
159        #clock-cells = <0>;
160        clock-frequency = <25000000>;
161    };
162
163    i2c@0 {
164        reg = <0x0 0x100>;
165        #address-cells = <1>;
166        #size-cells = <0>;
167
168        /* IDT 5P49V5923 I2C clock generator */
169        vc5: clock-generator@6a {
170            compatible = "idt,5p49v5923";
171            reg = <0x6a>;
172            #clock-cells = <1>;
173
174            /* Connect XIN input to 25MHz reference */
175            clocks = <&ref25m>;
176            clock-names = "xin";
177
178            /* Set the SD/OE pin's settings */
179            idt,shutdown = <0>;
180            idt,output-enable-active = <0>;
181
182            OUT1 {
183                idt,mode = <VC5_CMOSD>;
184                idt,voltage-microvolt = <1800000>;
185                idt,slew-percent = <80>;
186            };
187
188            OUT4 {
189                idt,mode = <VC5_LVDS>;
190            };
191        };
192    };
193
194...
195