1# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2%YAML 1.2
3---
4$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml#
5$schema: http://devicetree.org/meta-schemas/core.yaml#
6
7title: IDT VersaClock 5 and 6 programmable I2C clock generators
8
9description: |
10  The IDT VersaClock 5 and VersaClock 6 are programmable I2C
11  clock generators providing from 3 to 12 output clocks.
12
13  When referencing the provided clock in the DT using phandle and clock
14  specifier, the following mapping applies:
15
16  - 5P49V5923:
17    0 -- OUT0_SEL_I2CB
18    1 -- OUT1
19    2 -- OUT2
20
21  - 5P49V5933:
22    0 -- OUT0_SEL_I2CB
23    1 -- OUT1
24    2 -- OUT4
25
26  - other parts:
27    0 -- OUT0_SEL_I2CB
28    1 -- OUT1
29    2 -- OUT2
30    3 -- OUT3
31    4 -- OUT4
32
33  The idt,shutdown and idt,output-enable-active properties control the
34  SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown
35  Register, respectively. Their behavior is summarized by the following
36  table:
37
38  SH SP Output when the SD/OE pin is Low/High
39  == == =====================================
40   0  0 Active/Inactive
41   0  1 Inactive/Active
42   1  0 Active/Shutdown
43   1  1 Inactive/Shutdown
44
45  The case where SH and SP are both 1 is likely not very interesting.
46
47maintainers:
48  - Luca Ceresoli <luca.ceresoli@bootlin.com>
49
50properties:
51  compatible:
52    enum:
53      - idt,5p49v5923
54      - idt,5p49v5925
55      - idt,5p49v5933
56      - idt,5p49v5935
57      - idt,5p49v6901
58      - idt,5p49v6965
59      - idt,5p49v6975
60
61  reg:
62    description: I2C device address
63    enum: [ 0x68, 0x6a ]
64
65  '#clock-cells':
66    const: 1
67
68  clock-names:
69    minItems: 1
70    maxItems: 2
71    items:
72      enum: [ xin, clkin ]
73  clocks:
74    minItems: 1
75    maxItems: 2
76
77  idt,xtal-load-femtofarads:
78    minimum: 9000
79    maximum: 22760
80    description: Optional load capacitor for XTAL1 and XTAL2
81
82  idt,shutdown:
83    $ref: /schemas/types.yaml#/definitions/uint32
84    enum: [0, 1]
85    description: |
86      If 1, this enables the shutdown functionality: the chip will be
87      shut down if the SD/OE pin is driven high. If 0, this disables the
88      shutdown functionality: the chip will never be shut down based on
89      the value of the SD/OE pin. This property corresponds to the SH
90      bit of the Primary Source and Shutdown Register.
91
92  idt,output-enable-active:
93    $ref: /schemas/types.yaml#/definitions/uint32
94    enum: [0, 1]
95    description: |
96      If 1, this enables output when the SD/OE pin is high, and disables
97      output when the SD/OE pin is low. If 0, this disables output when
98      the SD/OE pin is high, and enables output when the SD/OE pin is
99      low. This corresponds to the SP bit of the Primary Source and
100      Shutdown Register.
101
102patternProperties:
103  "^OUT[1-4]$":
104    type: object
105    description:
106      Description of one of the outputs (OUT1..OUT4). See "Clock1 Output
107      Configuration" in the Versaclock 5/6/6E Family Register Description
108      and Programming Guide.
109    properties:
110      idt,mode:
111        description:
112          The output drive mode. Values defined in dt-bindings/clock/versaclock.h
113        $ref: /schemas/types.yaml#/definitions/uint32
114        minimum: 0
115        maximum: 6
116      idt,voltage-microvolt:
117        description: The output drive voltage.
118        enum: [ 1800000, 2500000, 3300000 ]
119      idt,slew-percent:
120        description: The Slew rate control for CMOS single-ended.
121        enum: [ 80, 85, 90, 100 ]
122    additionalProperties: false
123
124required:
125  - compatible
126  - reg
127  - '#clock-cells'
128  - idt,shutdown
129  - idt,output-enable-active
130
131allOf:
132  - if:
133      properties:
134        compatible:
135          enum:
136            - idt,5p49v5933
137            - idt,5p49v5935
138            - idt,5p49v6975
139    then:
140      # Devices with builtin crystal + optional external input
141      properties:
142        clock-names:
143          const: clkin
144        clocks:
145          maxItems: 1
146    else:
147      # Devices without builtin crystal
148      required:
149        - clock-names
150        - clocks
151
152additionalProperties: false
153
154examples:
155  - |
156    #include <dt-bindings/clock/versaclock.h>
157
158    /* 25MHz reference crystal */
159    ref25: ref25m {
160        compatible = "fixed-clock";
161        #clock-cells = <0>;
162        clock-frequency = <25000000>;
163    };
164
165    i2c@0 {
166        reg = <0x0 0x100>;
167        #address-cells = <1>;
168        #size-cells = <0>;
169
170        /* IDT 5P49V5923 I2C clock generator */
171        vc5: clock-generator@6a {
172            compatible = "idt,5p49v5923";
173            reg = <0x6a>;
174            #clock-cells = <1>;
175
176            /* Connect XIN input to 25MHz reference */
177            clocks = <&ref25m>;
178            clock-names = "xin";
179
180            /* Set the SD/OE pin's settings */
181            idt,shutdown = <0>;
182            idt,output-enable-active = <0>;
183
184            OUT1 {
185                idt,mode = <VC5_CMOSD>;
186                idt,voltage-microvolt = <1800000>;
187                idt,slew-percent = <80>;
188            };
189
190            OUT4 {
191                idt,mode = <VC5_LVDS>;
192            };
193        };
194    };
195
196...
197