1What:		/sys/class/hidraw/hidraw*/device/speed
2Date:		April 2010
3Kernel Version:	2.6.35
4Contact:	linux-bluetooth@vger.kernel.org
5Description:
6		The /sys/class/hidraw/hidraw*/device/speed file controls
7		reporting speed of Wacom bluetooth tablet. Reading from
8		this file returns 1 if tablet reports in high speed mode
9		or 0 otherwise. Writing to this file one of these values
10		switches reporting speed.
11
12What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/led
13Date:		August 2011
14Contact:	linux-input@vger.kernel.org
15Description:
16		Attribute group for control of the status LEDs and the OLEDs.
17		This attribute group is only available for Intuos 4 M, L,
18		and XL (with LEDs and OLEDs) and Cintiq 21UX2 and Cintiq 24HD
19		(LEDs only). Therefore its presence implicitly signifies the
20		presence of said LEDs and OLEDs on the tablet device.
21
22What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status0_luminance
23Date:		August 2011
24Contact:	linux-input@vger.kernel.org
25Description:
26		Writing to this file sets the status LED luminance (1..127)
27		when the stylus does not touch the tablet surface, and no
28		button is pressed on the stylus. This luminance level is
29		normally lower than the level when a button is pressed.
30
31What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status1_luminance
32Date:		August 2011
33Contact:	linux-input@vger.kernel.org
34Description:
35		Writing to this file sets the status LED luminance (1..127)
36		when the stylus touches the tablet surface, or any button is
37		pressed on the stylus.
38
39What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led0_select
40Date:		August 2011
41Contact:	linux-input@vger.kernel.org
42Description:
43		Writing to this file sets which one of the four (for Intuos 4)
44		or of the right four (for Cintiq 21UX2 and Cintiq 24HD) status
45		LEDs is active (0..3). The other three LEDs on the same side are
46		always inactive.
47
48What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/status_led1_select
49Date:		September 2011
50Contact:	linux-input@vger.kernel.org
51Description:
52		Writing to this file sets which one of the left four (for Cintiq 21UX2
53		and Cintiq 24HD) status LEDs is active (0..3). The other three LEDs on
54		the left are always inactive.
55
56What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/buttons_luminance
57Date:		August 2011
58Contact:	linux-input@vger.kernel.org
59Description:
60		Writing to this file sets the overall luminance level (0..15)
61		of all eight button OLED displays.
62
63What:		/sys/bus/usb/devices/<busnum>-<devnum>:<cfg>.<intf>/wacom_led/button<n>_rawimg
64Date:		August 2011
65Contact:	linux-input@vger.kernel.org
66Description:
67		When writing a 1024 byte raw image in Wacom Intuos 4
68		interleaving format to the file, the image shows up on Button N
69		of the device. The image is a 64x32 pixel 4-bit gray image. The
70		1024 byte binary is split up into 16x 64 byte chunks. Each 64
71		byte chunk encodes the image data for two consecutive lines on
72		the display. The low nibble of each byte contains the first
73		line, and the high nibble contains the second line.
74