1 /* 2 * Copyright (C) 2007-2013 Tensilica, Inc. 3 * Copyright (C) 2014 - 2016 Cadence Design Systems Inc. 4 * 5 * SPDX-License-Identifier: GPL-2.0+ 6 */ 7 8 #ifndef __CONFIG_H 9 #define __CONFIG_H 10 11 #include <asm/arch/core.h> 12 #include <asm/addrspace.h> 13 #include <asm/config.h> 14 15 /* 16 * The 'xtfpga' board describes a set of very similar boards with only minimal 17 * differences. 18 */ 19 20 /*=====================*/ 21 /* Board and Processor */ 22 /*=====================*/ 23 24 #define CONFIG_XTFPGA 25 26 /* FPGA CPU freq after init */ 27 #define CONFIG_SYS_CLK_FREQ (gd->cpu_clk) 28 29 /*===================*/ 30 /* RAM Layout */ 31 /*===================*/ 32 33 #if XCHAL_HAVE_PTP_MMU 34 #define CONFIG_SYS_MEMORY_BASE \ 35 (XCHAL_VECBASE_RESET_VADDR - XCHAL_VECBASE_RESET_PADDR) 36 #define CONFIG_SYS_IO_BASE 0xf0000000 37 #else 38 #define CONFIG_SYS_MEMORY_BASE 0x60000000 39 #define CONFIG_SYS_IO_BASE 0x90000000 40 #define CONFIG_MAX_MEM_MAPPED 0x10000000 41 #endif 42 43 /* Onboard RAM sizes: 44 * 45 * LX60 0x04000000 64 MB 46 * LX110 0x03000000 48 MB 47 * LX200 0x06000000 96 MB 48 * ML605 0x18000000 384 MB 49 * KC705 0x38000000 896 MB 50 * 51 * noMMU configurations can only see first 256MB of onboard memory. 52 */ 53 54 #if XCHAL_HAVE_PTP_MMU || CONFIG_BOARD_SDRAM_SIZE < 0x10000000 55 #define CONFIG_SYS_SDRAM_SIZE CONFIG_BOARD_SDRAM_SIZE 56 #else 57 #define CONFIG_SYS_SDRAM_SIZE 0x10000000 58 #endif 59 60 #define CONFIG_SYS_SDRAM_BASE MEMADDR(0x00000000) 61 62 /* Lx60 can only map 128kb memory (instead of 256kb) when running under OCD */ 63 #ifdef CONFIG_XTFPGA_LX60 64 # define CONFIG_SYS_MONITOR_LEN 0x00020000 /* 128KB */ 65 #else 66 # define CONFIG_SYS_MONITOR_LEN 0x00040000 /* 256KB */ 67 #endif 68 69 #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* heap 256KB */ 70 71 /* Linux boot param area in RAM (used only when booting linux) */ 72 #define CONFIG_SYS_BOOTPARAMS_LEN (64 << 10) 73 74 /* Memory test is destructive so default must not overlap vectors or U-Boot*/ 75 #define CONFIG_SYS_MEMTEST_START MEMADDR(0x01000000) 76 #define CONFIG_SYS_MEMTEST_END MEMADDR(0x02000000) 77 78 /* Load address for stand-alone applications. 79 * MEMADDR cannot be used here, because the definition needs to be 80 * a plain number as it's used as -Ttext argument for ld in standalone 81 * example makefile. 82 * Handle noMMU vs MMUv2 vs MMUv3 distinction here manually. 83 */ 84 #if XCHAL_HAVE_PTP_MMU 85 #if XCHAL_VECBASE_RESET_VADDR == XCHAL_VECBASE_RESET_PADDR 86 #define CONFIG_STANDALONE_LOAD_ADDR 0x00800000 87 #else 88 #define CONFIG_STANDALONE_LOAD_ADDR 0xd0800000 89 #endif 90 #else 91 #define CONFIG_STANDALONE_LOAD_ADDR 0x60800000 92 #endif 93 94 #if defined(CONFIG_MAX_MEM_MAPPED) && \ 95 CONFIG_MAX_MEM_MAPPED < CONFIG_SYS_SDRAM_SIZE 96 #define CONFIG_SYS_MEMORY_SIZE CONFIG_MAX_MEM_MAPPED 97 #else 98 #define CONFIG_SYS_MEMORY_SIZE CONFIG_SYS_SDRAM_SIZE 99 #endif 100 101 #define CONFIG_SYS_MEMORY_TOP MEMADDR(CONFIG_SYS_MEMORY_SIZE) 102 #define CONFIG_SYS_TEXT_ADDR \ 103 (CONFIG_SYS_MEMORY_TOP - CONFIG_SYS_MONITOR_LEN) 104 105 /* Used by tftpboot; env var 'loadaddr' */ 106 #define CONFIG_SYS_LOAD_ADDR MEMADDR(0x02000000) 107 108 /*==============================*/ 109 /* U-Boot general configuration */ 110 /*==============================*/ 111 112 #define CONFIG_BOARD_POSTCLK_INIT 113 #define CONFIG_MISC_INIT_R 114 115 #define CONFIG_BOOTFILE "uImage" 116 /* Console I/O Buffer Size */ 117 #define CONFIG_SYS_CBSIZE 1024 118 /* max number of command args */ 119 #define CONFIG_SYS_MAXARGS 16 120 /* Boot Argument Buffer Size */ 121 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE 122 123 /*==============================*/ 124 /* U-Boot autoboot configuration */ 125 /*==============================*/ 126 127 #define CONFIG_BOOT_RETRY_TIME 60 /* retry after 60 secs */ 128 129 #define CONFIG_AUTO_COMPLETE /* Support tab autocompletion */ 130 #define CONFIG_CMDLINE_EDITING 131 #define CONFIG_SYS_LONGHELP 132 #define CONFIG_MX_CYCLIC 133 #define CONFIG_SHOW_BOOT_PROGRESS 134 135 #ifdef DEBUG 136 #define CONFIG_PANIC_HANG 1 /* Require manual reboot */ 137 #endif 138 139 140 /*=========================================*/ 141 /* FPGA Registers (board info and control) */ 142 /*=========================================*/ 143 144 /* 145 * These assume FPGA bitstreams from Tensilica release RB and up. Earlier 146 * releases may not provide any/all of these registers or at these offsets. 147 * Some of the FPGA registers are broken down into bitfields described by 148 * SHIFT left amount and field WIDTH (bits), and also by a bitMASK. 149 */ 150 151 /* Date of FPGA bitstream build in binary coded decimal (BCD) */ 152 #define CONFIG_SYS_FPGAREG_DATE IOADDR(0x0D020000) 153 #define FPGAREG_MTH_SHIFT 24 /* BCD month 1..12 */ 154 #define FPGAREG_MTH_WIDTH 8 155 #define FPGAREG_MTH_MASK 0xFF000000 156 #define FPGAREG_DAY_SHIFT 16 /* BCD day 1..31 */ 157 #define FPGAREG_DAY_WIDTH 8 158 #define FPGAREG_DAY_MASK 0x00FF0000 159 #define FPGAREG_YEAR_SHIFT 0 /* BCD year 2001..9999*/ 160 #define FPGAREG_YEAR_WIDTH 16 161 #define FPGAREG_YEAR_MASK 0x0000FFFF 162 163 /* FPGA core clock frequency in Hz (also input to UART) */ 164 #define CONFIG_SYS_FPGAREG_FREQ IOADDR(0x0D020004) /* CPU clock frequency*/ 165 166 /* 167 * DIP switch (left=sw1=lsb=bit0, right=sw8=msb=bit7; off=0, on=1): 168 * Bits 0..5 set the lower 6 bits of the default ethernet MAC. 169 * Bit 6 is reserved for future use by Tensilica. 170 * Bit 7 maps the first 128KB of ROM address space at CONFIG_SYS_ROM_BASE to 171 * the base of flash * (when on/1) or to the base of RAM (when off/0). 172 */ 173 #define CONFIG_SYS_FPGAREG_DIPSW IOADDR(0x0D02000C) 174 #define FPGAREG_MAC_SHIFT 0 /* Ethernet MAC bits 0..5 */ 175 #define FPGAREG_MAC_WIDTH 6 176 #define FPGAREG_MAC_MASK 0x3f 177 #define FPGAREG_BOOT_SHIFT 7 /* Boot ROM addr mapping */ 178 #define FPGAREG_BOOT_WIDTH 1 179 #define FPGAREG_BOOT_MASK 0x80 180 #define FPGAREG_BOOT_RAM 0 181 #define FPGAREG_BOOT_FLASH (1<<FPGAREG_BOOT_SHIFT) 182 183 /* Force hard reset of board by writing a code to this register */ 184 #define CONFIG_SYS_FPGAREG_RESET IOADDR(0x0D020010) /* Reset board .. */ 185 #define CONFIG_SYS_FPGAREG_RESET_CODE 0x0000DEAD /* by writing this code */ 186 187 /*====================*/ 188 /* Serial Driver Info */ 189 /*====================*/ 190 191 #define CONFIG_SYS_NS16550_SERIAL 192 #define CONFIG_SYS_NS16550_REG_SIZE (-4) 193 #define CONFIG_SYS_NS16550_COM1 IOADDR(0x0D050020) /* Base address */ 194 195 /* Input clk to NS16550 (in Hz; the SYS_CLK_FREQ is in kHz) */ 196 #define CONFIG_SYS_NS16550_CLK CONFIG_SYS_CLK_FREQ 197 #define CONFIG_CONS_INDEX 1 /* use UART0 for console */ 198 #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } 199 200 /*======================*/ 201 /* Ethernet Driver Info */ 202 /*======================*/ 203 204 #define CONFIG_ETHBASE 00:50:C2:13:6f:00 205 #define CONFIG_SYS_ETHOC_BASE IOADDR(0x0d030000) 206 #define CONFIG_SYS_ETHOC_BUFFER_ADDR IOADDR(0x0D800000) 207 208 /*=====================*/ 209 /* Flash & Environment */ 210 /*=====================*/ 211 212 #define CONFIG_SYS_FLASH_CFI 213 #define CONFIG_FLASH_CFI_DRIVER /* use generic CFI driver */ 214 #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT 215 #define CONFIG_SYS_MAX_FLASH_BANKS 1 216 #ifdef CONFIG_XTFPGA_LX60 217 # define CONFIG_SYS_FLASH_SIZE 0x0040000 /* 4MB */ 218 # define CONFIG_SYS_FLASH_SECT_SZ 0x10000 /* block size 64KB */ 219 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x2000 /* param size 8KB */ 220 # define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000) 221 # define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 222 #elif defined(CONFIG_XTFPGA_KC705) 223 # define CONFIG_SYS_FLASH_SIZE 0x8000000 /* 128MB */ 224 # define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */ 225 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */ 226 # define CONFIG_SYS_FLASH_BASE IOADDR(0x00000000) 227 # define CONFIG_SYS_MONITOR_BASE IOADDR(0x06000000) 228 #else 229 # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* 16MB */ 230 # define CONFIG_SYS_FLASH_SECT_SZ 0x20000 /* block size 128KB */ 231 # define CONFIG_SYS_FLASH_PARMSECT_SZ 0x8000 /* param size 32KB */ 232 # define CONFIG_SYS_FLASH_BASE IOADDR(0x08000000) 233 # define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 234 #endif 235 #define CONFIG_SYS_MAX_FLASH_SECT \ 236 (CONFIG_SYS_FLASH_SECT_SZ/CONFIG_SYS_FLASH_PARMSECT_SZ + \ 237 CONFIG_SYS_FLASH_SIZE/CONFIG_SYS_FLASH_SECT_SZ - 1) 238 #define CONFIG_SYS_FLASH_PROTECTION /* hw flash protection */ 239 240 /* 241 * Put environment in top block (64kB) 242 * Another option would be to put env. in 2nd param block offs 8KB, size 8KB 243 */ 244 #define CONFIG_ENV_OFFSET (CONFIG_SYS_FLASH_SIZE - CONFIG_SYS_FLASH_SECT_SZ) 245 #define CONFIG_ENV_SIZE CONFIG_SYS_FLASH_SECT_SZ 246 247 /* print 'E' for empty sector on flinfo */ 248 #define CONFIG_SYS_FLASH_EMPTY_INFO 249 250 #endif /* __CONFIG_H */ 251