1 /* 2 * Copyright 2010 Extreme Engineering Solutions, Inc. 3 * Copyright 2007-2008 Freescale Semiconductor, Inc. 4 * 5 * See file CREDITS for list of people who contributed to this 6 * project. 7 * 8 * This program is free software; you can redistribute it and/or 9 * modify it under the terms of the GNU General Public License as 10 * published by the Free Software Foundation; either version 2 of 11 * the License, or (at your option) any later version. 12 * This program is distributed in the hope that it will be useful, 13 * but WITHOUT ANY WARRANTY; without even the implied warranty of 14 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the 15 * GNU General Public License for more details. 16 * 17 * You should have received a copy of the GNU General Public License 18 * along with this program; if not, write to the Free Software 19 * Foundation, Inc., 59 Temple Place, Suite 330, Boston, 20 * MA 02111-1307 USA 21 */ 22 23 /* 24 * xpedite550x board configuration file 25 */ 26 #ifndef __CONFIG_H 27 #define __CONFIG_H 28 29 /* 30 * High Level Configuration Options 31 */ 32 #define CONFIG_BOOKE 1 /* BOOKE */ 33 #define CONFIG_E500 1 /* BOOKE e500 family */ 34 #define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */ 35 #define CONFIG_P2020 1 36 #define CONFIG_XPEDITE550X 1 37 #define CONFIG_SYS_BOARD_NAME "XPedite5500" 38 #define CONFIG_SYS_FORM_PMC_XMC 1 39 #define CONFIG_PRPMC_PCI_ALIAS "pci0" /* Processor PMC interface on pci0 */ 40 #define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */ 41 42 #ifndef CONFIG_SYS_TEXT_BASE 43 #define CONFIG_SYS_TEXT_BASE 0xfff80000 44 #endif 45 46 #define CONFIG_PCI 1 /* Enable PCI/PCIE */ 47 #define CONFIG_PCI_PNP 1 /* do pci plug-and-play */ 48 #define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */ 49 #define CONFIG_PCIE1 1 /* PCIE controler 1 (PEX8112 or XMC) */ 50 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 51 #define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */ 52 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 53 #define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */ 54 #define CONFIG_FSL_LAW 1 /* Use common FSL init code */ 55 #define CONFIG_FSL_ELBC 1 56 57 /* 58 * Multicore config 59 */ 60 #define CONFIG_MP 61 #define CONFIG_BPTR_VIRT_ADDR 0xee000000 /* virt boot page address */ 62 #define CONFIG_MPC8xxx_DISABLE_BPTR /* Don't leave BPTR enabled */ 63 64 /* 65 * DDR config 66 */ 67 #define CONFIG_FSL_DDR3 68 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 69 #define CONFIG_DDR_SPD 70 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 71 #define SPD_EEPROM_ADDRESS 0x54 72 #define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */ 73 #define CONFIG_NUM_DDR_CONTROLLERS 1 74 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 75 #define CONFIG_CHIP_SELECTS_PER_CTRL 2 76 #define CONFIG_DDR_ECC 77 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 78 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 79 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 80 #define CONFIG_VERY_BIG_RAM 81 82 #ifndef __ASSEMBLY__ 83 extern unsigned long get_board_sys_clk(unsigned long dummy); 84 extern unsigned long get_board_ddr_clk(unsigned long dummy); 85 #endif 86 87 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */ 88 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */ 89 90 /* 91 * These can be toggled for performance analysis, otherwise use default. 92 */ 93 #define CONFIG_L2_CACHE /* toggle L2 cache */ 94 #define CONFIG_BTB /* toggle branch predition */ 95 #define CONFIG_ENABLE_36BIT_PHYS 1 96 97 #define CONFIG_SYS_CCSRBAR 0xef000000 98 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 99 100 /* 101 * Diagnostics 102 */ 103 #define CONFIG_SYS_ALT_MEMTEST 104 #define CONFIG_SYS_MEMTEST_START 0x10000000 105 #define CONFIG_SYS_MEMTEST_END 0x20000000 106 #define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \ 107 CONFIG_SYS_POST_I2C) 108 #define I2C_ADDR_LIST {CONFIG_SYS_I2C_EEPROM_ADDR, \ 109 CONFIG_SYS_I2C_LM75_ADDR, \ 110 CONFIG_SYS_I2C_LM90_ADDR, \ 111 CONFIG_SYS_I2C_PCA953X_ADDR0, \ 112 CONFIG_SYS_I2C_PCA953X_ADDR2, \ 113 CONFIG_SYS_I2C_PCA953X_ADDR3, \ 114 CONFIG_SYS_I2C_RTC_ADDR} 115 116 /* 117 * Memory map 118 * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable 119 * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable 120 * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable 121 * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable 122 * 0xee00_0000 0xee00_ffff Boot page translation 4K non-cacheable 123 * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable 124 * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable 125 * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable 126 * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable 127 */ 128 129 #define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_8 | LCRR_EADC_3) 130 131 /* 132 * NAND flash configuration 133 */ 134 #define CONFIG_SYS_NAND_BASE 0xef800000 135 #define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */ 136 #define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE, \ 137 CONFIG_SYS_NAND_BASE2} 138 #define CONFIG_SYS_MAX_NAND_DEVICE 2 139 #define CONFIG_MTD_NAND_VERIFY_WRITE 140 #define CONFIG_SYS_NAND_QUIET_TEST /* 2nd NAND flash not always populated */ 141 #define CONFIG_NAND_FSL_ELBC 142 143 /* 144 * NOR flash configuration 145 */ 146 #define CONFIG_SYS_FLASH_BASE 0xf8000000 147 #define CONFIG_SYS_FLASH_BASE2 0xf0000000 148 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2} 149 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 150 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 151 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 152 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 153 #define CONFIG_FLASH_CFI_DRIVER 154 #define CONFIG_SYS_FLASH_CFI 155 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 156 #define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \ 157 {0xf7f40000, 0xc0000} } 158 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 159 160 /* 161 * Chip select configuration 162 */ 163 /* NOR Flash 0 on CS0 */ 164 #define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \ 165 BR_PS_16 | \ 166 BR_V) 167 #define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \ 168 OR_GPCM_CSNT | \ 169 OR_GPCM_XACS | \ 170 OR_GPCM_ACS_DIV2 | \ 171 OR_GPCM_SCY_8 | \ 172 OR_GPCM_TRLX | \ 173 OR_GPCM_EHTR | \ 174 OR_GPCM_EAD) 175 176 /* NOR Flash 1 on CS1 */ 177 #define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \ 178 BR_PS_16 | \ 179 BR_V) 180 #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM 181 182 /* NAND flash on CS2 */ 183 #define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \ 184 (2<<BR_DECC_SHIFT) | \ 185 BR_PS_8 | \ 186 BR_MS_FCM | \ 187 BR_V) 188 189 /* NAND flash on CS2 */ 190 #define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \ 191 OR_FCM_PGS | \ 192 OR_FCM_CSCT | \ 193 OR_FCM_CST | \ 194 OR_FCM_CHT | \ 195 OR_FCM_SCY_1 | \ 196 OR_FCM_TRLX | \ 197 OR_FCM_EHTR) 198 199 /* NAND flash on CS3 */ 200 #define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \ 201 (2<<BR_DECC_SHIFT) | \ 202 BR_PS_8 | \ 203 BR_MS_FCM | \ 204 BR_V) 205 #define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM 206 207 /* 208 * Use L1 as initial stack 209 */ 210 #define CONFIG_SYS_INIT_RAM_LOCK 1 211 #define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000 212 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 213 214 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 215 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 216 217 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */ 218 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 219 220 /* 221 * Serial Port 222 */ 223 #define CONFIG_CONS_INDEX 1 224 #define CONFIG_SYS_NS16550 225 #define CONFIG_SYS_NS16550_SERIAL 226 #define CONFIG_SYS_NS16550_REG_SIZE 1 227 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 228 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 229 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 230 #define CONFIG_SYS_BAUDRATE_TABLE \ 231 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} 232 #define CONFIG_BAUDRATE 115200 233 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 234 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 235 236 /* 237 * Use the HUSH parser 238 */ 239 #define CONFIG_SYS_HUSH_PARSER 240 241 /* 242 * Pass open firmware flat tree 243 */ 244 #define CONFIG_OF_LIBFDT 1 245 #define CONFIG_OF_BOARD_SETUP 1 246 #define CONFIG_OF_STDOUT_VIA_ALIAS 1 247 #define CONFIG_FDT_FIXUP_PCI_IRQ 1 248 249 /* 250 * I2C 251 */ 252 #define CONFIG_SYS_I2C 253 #define CONFIG_SYS_I2C_FSL 254 #define CONFIG_SYS_FSL_I2C_SPEED 400000 255 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 256 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 257 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 258 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 259 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 260 261 /* I2C DS7505 temperature sensor */ 262 #define CONFIG_DTT_LM75 263 #define CONFIG_DTT_SENSORS { 0 } 264 #define CONFIG_SYS_I2C_LM75_ADDR 0x48 265 266 /* I2C ADT7461 temperature sensor */ 267 #define CONFIG_SYS_I2C_LM90_ADDR 0x4C 268 269 /* I2C EEPROM - AT24C128B */ 270 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 271 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 272 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */ 273 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */ 274 275 /* I2C RTC */ 276 #define CONFIG_RTC_M41T11 1 277 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 278 #define CONFIG_SYS_M41T11_BASE_YEAR 2000 279 280 /* GPIO */ 281 #define CONFIG_PCA953X 282 #define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18 283 #define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c 284 #define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e 285 #define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f 286 #define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0 287 288 /* 289 * GPIO pin definitions, PU = pulled high, PD = pulled low 290 */ 291 /* PCA9557 @ 0x18*/ 292 #define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */ 293 #define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select (1: RS-485, 0: RS-232) */ 294 #define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */ 295 #define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select (1: RS-485, 0: RS-232) */ 296 #define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */ 297 #define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Write protection (0: disabled, 1: enabled) */ 298 299 /* PCA9557 @ 0x1e*/ 300 #define CONFIG_SYS_PCA953X_XMC_GA0 0x01 /* PU; */ 301 #define CONFIG_SYS_PCA953X_XMC_GA1 0x02 /* PU; */ 302 #define CONFIG_SYS_PCA953X_XMC_GA2 0x04 /* PU; */ 303 #define CONFIG_SYS_PCA953X_XMC_WAKE 0x10 /* PU; */ 304 #define CONFIG_SYS_PCA953X_XMC_BIST 0x20 /* Enable XMC BIST */ 305 #define CONFIG_SYS_PCA953X_PMC_EREADY 0x40 /* PU; PMC PCI eready */ 306 #define CONFIG_SYS_PCA953X_PMC_MONARCH 0x80 /* PMC monarch mode enable */ 307 308 /* PCA9557 @ 0x1f */ 309 #define CONFIG_SYS_PCA953X_MC_GPIO0 0x01 /* PU; */ 310 #define CONFIG_SYS_PCA953X_MC_GPIO1 0x02 /* PU; */ 311 #define CONFIG_SYS_PCA953X_MC_GPIO2 0x04 /* PU; */ 312 #define CONFIG_SYS_PCA953X_MC_GPIO3 0x08 /* PU; */ 313 #define CONFIG_SYS_PCA953X_MC_GPIO4 0x10 /* PU; */ 314 #define CONFIG_SYS_PCA953X_MC_GPIO5 0x20 /* PU; */ 315 #define CONFIG_SYS_PCA953X_MC_GPIO6 0x40 /* PU; */ 316 #define CONFIG_SYS_PCA953X_MC_GPIO7 0x80 /* PU; */ 317 318 /* 319 * General PCI 320 * Memory space is mapped 1-1, but I/O space must start from 0. 321 */ 322 323 /* controller 1 - PEX8112 or XMC, depending on build option */ 324 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 325 #define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BUS 326 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */ 327 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 328 #define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000 329 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */ 330 331 332 /* 333 * Networking options 334 */ 335 #define CONFIG_TSEC_ENET /* tsec ethernet support */ 336 #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ 337 #define CONFIG_TSEC_TBI 338 #define CONFIG_MII 1 /* MII PHY management */ 339 #define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */ 340 #define CONFIG_ETHPRIME "eTSEC2" 341 342 /* 343 * In-band SGMII auto-negotiation between TBI and BCM5482S PHY fails, force 344 * 1000mbps SGMII link 345 */ 346 #define CONFIG_TSEC_TBICR_SETTINGS ( \ 347 TBICR_PHY_RESET \ 348 | TBICR_FULL_DUPLEX \ 349 | TBICR_SPEED1_SET \ 350 ) 351 352 #define CONFIG_TSEC1 1 353 #define CONFIG_TSEC1_NAME "eTSEC1" 354 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 355 #define TSEC1_PHY_ADDR 1 356 #define TSEC1_PHYIDX 0 357 #define CONFIG_HAS_ETH0 358 359 #define CONFIG_TSEC2 1 360 #define CONFIG_TSEC2_NAME "eTSEC2" 361 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 362 #define TSEC2_PHY_ADDR 2 363 #define TSEC2_PHYIDX 0 364 #define CONFIG_HAS_ETH1 365 366 #define CONFIG_TSEC3 1 367 #define CONFIG_TSEC3_NAME "eTSEC3" 368 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 369 #define TSEC3_PHY_ADDR 3 370 #define TSEC3_PHYIDX 0 371 #define CONFIG_HAS_ETH2 372 373 /* 374 * USB 375 */ 376 #define CONFIG_USB_STORAGE 377 #define CONFIG_USB_EHCI 378 #define CONFIG_USB_EHCI_FSL 379 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 380 #define CONFIG_DOS_PARTITION 381 382 /* 383 * Command configuration. 384 */ 385 #include <config_cmd_default.h> 386 387 #define CONFIG_CMD_ASKENV 388 #define CONFIG_CMD_DATE 389 #define CONFIG_CMD_DHCP 390 #define CONFIG_CMD_DTT 391 #define CONFIG_CMD_EEPROM 392 #define CONFIG_CMD_ELF 393 #define CONFIG_CMD_FLASH 394 #define CONFIG_CMD_I2C 395 #define CONFIG_CMD_JFFS2 396 #define CONFIG_CMD_MII 397 #define CONFIG_CMD_NAND 398 #define CONFIG_CMD_NET 399 #define CONFIG_CMD_PCA953X 400 #define CONFIG_CMD_PCA953X_INFO 401 #define CONFIG_CMD_PCI 402 #define CONFIG_CMD_PCI_ENUM 403 #define CONFIG_CMD_PING 404 #define CONFIG_CMD_REGINFO 405 #define CONFIG_CMD_SAVEENV 406 #define CONFIG_CMD_SNTP 407 #define CONFIG_CMD_USB 408 409 /* 410 * Miscellaneous configurable options 411 */ 412 #define CONFIG_SYS_LONGHELP /* undef to save memory */ 413 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 414 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ 415 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ 416 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ 417 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ 418 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ 419 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ 420 #define CONFIG_CMDLINE_EDITING 1 /* add command line history */ 421 #define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */ 422 #define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */ 423 #define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */ 424 #define CONFIG_PANIC_HANG /* do not reset board on panic */ 425 #define CONFIG_PREBOOT /* enable preboot variable */ 426 #define CONFIG_FIT 1 427 #define CONFIG_FIT_VERBOSE 1 428 #define CONFIG_INTEGRITY /* support booting INTEGRITY OS */ 429 430 /* 431 * For booting Linux, the board info and command line data 432 * have to be in the first 16 MB of memory, since this is 433 * the maximum mapped by the Linux kernel during initialization. 434 */ 435 #define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/ 436 #define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */ 437 438 /* 439 * Environment Configuration 440 */ 441 #define CONFIG_ENV_IS_IN_FLASH 1 442 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */ 443 #define CONFIG_ENV_SIZE 0x8000 444 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024)) 445 446 /* 447 * Flash memory map: 448 * fff80000 - ffffffff Pri U-Boot (512 KB) 449 * fff40000 - fff7ffff Pri U-Boot Environment (256 KB) 450 * fff00000 - fff3ffff Pri FDT (256KB) 451 * fef00000 - ffefffff Pri OS image (16MB) 452 * f8000000 - feefffff Pri OS Use/Filesystem (111MB) 453 * 454 * f7f80000 - f7ffffff Sec U-Boot (512 KB) 455 * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB) 456 * f7f00000 - f7f3ffff Sec FDT (256KB) 457 * f6f00000 - f7efffff Sec OS image (16MB) 458 * f0000000 - f6efffff Sec OS Use/Filesystem (111MB) 459 */ 460 #define CONFIG_UBOOT1_ENV_ADDR __stringify(0xfff80000) 461 #define CONFIG_UBOOT2_ENV_ADDR __stringify(0xf7f80000) 462 #define CONFIG_FDT1_ENV_ADDR __stringify(0xfff00000) 463 #define CONFIG_FDT2_ENV_ADDR __stringify(0xf7f00000) 464 #define CONFIG_OS1_ENV_ADDR __stringify(0xfef00000) 465 #define CONFIG_OS2_ENV_ADDR __stringify(0xf6f00000) 466 467 #define CONFIG_PROG_UBOOT1 \ 468 "$download_cmd $loadaddr $ubootfile; " \ 469 "if test $? -eq 0; then " \ 470 "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 471 "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 472 "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \ 473 "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \ 474 "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \ 475 "if test $? -ne 0; then " \ 476 "echo PROGRAM FAILED; " \ 477 "else; " \ 478 "echo PROGRAM SUCCEEDED; " \ 479 "fi; " \ 480 "else; " \ 481 "echo DOWNLOAD FAILED; " \ 482 "fi;" 483 484 #define CONFIG_PROG_UBOOT2 \ 485 "$download_cmd $loadaddr $ubootfile; " \ 486 "if test $? -eq 0; then " \ 487 "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 488 "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 489 "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \ 490 "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \ 491 "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \ 492 "if test $? -ne 0; then " \ 493 "echo PROGRAM FAILED; " \ 494 "else; " \ 495 "echo PROGRAM SUCCEEDED; " \ 496 "fi; " \ 497 "else; " \ 498 "echo DOWNLOAD FAILED; " \ 499 "fi;" 500 501 #define CONFIG_BOOT_OS_NET \ 502 "$download_cmd $osaddr $osfile; " \ 503 "if test $? -eq 0; then " \ 504 "if test -n $fdtaddr; then " \ 505 "$download_cmd $fdtaddr $fdtfile; " \ 506 "if test $? -eq 0; then " \ 507 "bootm $osaddr - $fdtaddr; " \ 508 "else; " \ 509 "echo FDT DOWNLOAD FAILED; " \ 510 "fi; " \ 511 "else; " \ 512 "bootm $osaddr; " \ 513 "fi; " \ 514 "else; " \ 515 "echo OS DOWNLOAD FAILED; " \ 516 "fi;" 517 518 #define CONFIG_PROG_OS1 \ 519 "$download_cmd $osaddr $osfile; " \ 520 "if test $? -eq 0; then " \ 521 "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \ 522 "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 523 "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \ 524 "if test $? -ne 0; then " \ 525 "echo OS PROGRAM FAILED; " \ 526 "else; " \ 527 "echo OS PROGRAM SUCCEEDED; " \ 528 "fi; " \ 529 "else; " \ 530 "echo OS DOWNLOAD FAILED; " \ 531 "fi;" 532 533 #define CONFIG_PROG_OS2 \ 534 "$download_cmd $osaddr $osfile; " \ 535 "if test $? -eq 0; then " \ 536 "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \ 537 "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 538 "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \ 539 "if test $? -ne 0; then " \ 540 "echo OS PROGRAM FAILED; " \ 541 "else; " \ 542 "echo OS PROGRAM SUCCEEDED; " \ 543 "fi; " \ 544 "else; " \ 545 "echo OS DOWNLOAD FAILED; " \ 546 "fi;" 547 548 #define CONFIG_PROG_FDT1 \ 549 "$download_cmd $fdtaddr $fdtfile; " \ 550 "if test $? -eq 0; then " \ 551 "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \ 552 "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 553 "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \ 554 "if test $? -ne 0; then " \ 555 "echo FDT PROGRAM FAILED; " \ 556 "else; " \ 557 "echo FDT PROGRAM SUCCEEDED; " \ 558 "fi; " \ 559 "else; " \ 560 "echo FDT DOWNLOAD FAILED; " \ 561 "fi;" 562 563 #define CONFIG_PROG_FDT2 \ 564 "$download_cmd $fdtaddr $fdtfile; " \ 565 "if test $? -eq 0; then " \ 566 "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \ 567 "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 568 "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \ 569 "if test $? -ne 0; then " \ 570 "echo FDT PROGRAM FAILED; " \ 571 "else; " \ 572 "echo FDT PROGRAM SUCCEEDED; " \ 573 "fi; " \ 574 "else; " \ 575 "echo FDT DOWNLOAD FAILED; " \ 576 "fi;" 577 578 #define CONFIG_EXTRA_ENV_SETTINGS \ 579 "autoload=yes\0" \ 580 "download_cmd=tftp\0" \ 581 "console_args=console=ttyS0,115200\0" \ 582 "root_args=root=/dev/nfs rw\0" \ 583 "misc_args=ip=on\0" \ 584 "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \ 585 "bootfile=/home/user/file\0" \ 586 "osfile=/home/user/board.uImage\0" \ 587 "fdtfile=/home/user/board.dtb\0" \ 588 "ubootfile=/home/user/u-boot.bin\0" \ 589 "fdtaddr=c00000\0" \ 590 "osaddr=0x1000000\0" \ 591 "loadaddr=0x1000000\0" \ 592 "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \ 593 "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \ 594 "prog_os1="CONFIG_PROG_OS1"\0" \ 595 "prog_os2="CONFIG_PROG_OS2"\0" \ 596 "prog_fdt1="CONFIG_PROG_FDT1"\0" \ 597 "prog_fdt2="CONFIG_PROG_FDT2"\0" \ 598 "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \ 599 "bootcmd_flash1=run set_bootargs; " \ 600 "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\ 601 "bootcmd_flash2=run set_bootargs; " \ 602 "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\ 603 "bootcmd=run bootcmd_flash1\0" 604 #endif /* __CONFIG_H */ 605