1 /* 2 * Configuation settings for the SAMA5D3xEK board. 3 * 4 * Copyright (C) 2012 - 2013 Atmel 5 * 6 * based on at91sam9m10g45ek.h by: 7 * Stelian Pop <stelian@popies.net> 8 * Lead Tech Design <www.leadtechdesign.com> 9 * 10 * SPDX-License-Identifier: GPL-2.0+ 11 */ 12 13 #ifndef __CONFIG_H 14 #define __CONFIG_H 15 16 #include "at91-sama5_common.h" 17 18 /* 19 * This needs to be defined for the OHCI code to work but it is defined as 20 * ATMEL_ID_UHPHS in the CPU specific header files. 21 */ 22 #define ATMEL_ID_UHP 32 23 24 /* 25 * Specify the clock enable bit in the PMC_SCER register. 26 */ 27 #define ATMEL_PMC_UHP (1 << 6) 28 29 /* board specific (not enough SRAM) */ 30 #define CONFIG_SAMA5D3_LCD_BASE 0x23E00000 31 32 /* NOR flash */ 33 #ifdef CONFIG_MTD_NOR_FLASH 34 #define CONFIG_FLASH_CFI_DRIVER 35 #define CONFIG_SYS_FLASH_CFI 36 #define CONFIG_SYS_FLASH_PROTECTION 37 #define CONFIG_SYS_FLASH_BASE 0x10000000 38 #define CONFIG_SYS_MAX_FLASH_SECT 131 39 #define CONFIG_SYS_MAX_FLASH_BANKS 1 40 #endif 41 42 /* SDRAM */ 43 #define CONFIG_NR_DRAM_BANKS 1 44 #define CONFIG_SYS_SDRAM_BASE 0x20000000 45 #define CONFIG_SYS_SDRAM_SIZE 0x20000000 46 47 #ifdef CONFIG_SPL_BUILD 48 #define CONFIG_SYS_INIT_SP_ADDR 0x318000 49 #else 50 #define CONFIG_SYS_INIT_SP_ADDR \ 51 (CONFIG_SYS_SDRAM_BASE + 16 * 1024 - GENERATED_GBL_DATA_SIZE) 52 #endif 53 54 /* SerialFlash */ 55 56 #ifdef CONFIG_CMD_SF 57 #define CONFIG_SF_DEFAULT_SPEED 30000000 58 #endif 59 60 /* NAND flash */ 61 #ifdef CONFIG_CMD_NAND 62 #define CONFIG_NAND_ATMEL 63 #define CONFIG_SYS_MAX_NAND_DEVICE 1 64 #define CONFIG_SYS_NAND_BASE 0x60000000 65 /* our ALE is AD21 */ 66 #define CONFIG_SYS_NAND_MASK_ALE (1 << 21) 67 /* our CLE is AD22 */ 68 #define CONFIG_SYS_NAND_MASK_CLE (1 << 22) 69 #define CONFIG_SYS_NAND_ONFI_DETECTION 70 #endif 71 /* PMECC & PMERRLOC */ 72 #define CONFIG_ATMEL_NAND_HWECC 73 #define CONFIG_ATMEL_NAND_HW_PMECC 74 #define CONFIG_PMECC_CAP 4 75 #define CONFIG_PMECC_SECTOR_SIZE 512 76 77 /* USB */ 78 79 #ifdef CONFIG_CMD_USB 80 #define CONFIG_USB_ATMEL_CLK_SEL_UPLL 81 #define CONFIG_USB_OHCI_NEW 82 #define CONFIG_SYS_USB_OHCI_CPU_INIT 83 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_BASE_OHCI 84 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "sama5d3" 85 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 3 86 #endif 87 88 #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ 89 90 /* SPL */ 91 #define CONFIG_SPL_TEXT_BASE 0x300000 92 #define CONFIG_SPL_MAX_SIZE 0x18000 93 #define CONFIG_SPL_BSS_START_ADDR 0x20000000 94 #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 95 #define CONFIG_SYS_SPL_MALLOC_START 0x20080000 96 #define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 97 98 #define CONFIG_SYS_MONITOR_LEN (512 << 10) 99 100 #ifdef CONFIG_SD_BOOT 101 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1 102 #define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img" 103 104 #elif CONFIG_SPI_BOOT 105 #define CONFIG_SYS_SPI_U_BOOT_OFFS 0x10000 106 107 #elif CONFIG_NAND_BOOT 108 #define CONFIG_SPL_NAND_DRIVERS 109 #define CONFIG_SPL_NAND_BASE 110 #endif 111 #define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000 112 #define CONFIG_SYS_NAND_5_ADDR_CYCLE 113 #define CONFIG_SYS_NAND_PAGE_SIZE 0x800 114 #define CONFIG_SYS_NAND_PAGE_COUNT 64 115 #define CONFIG_SYS_NAND_OOBSIZE 64 116 #define CONFIG_SYS_NAND_BLOCK_SIZE 0x20000 117 #define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0 118 #define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER 119 120 #endif 121