1 /* 2 * Copyright (C) 2010 Andreas Bießmann <biessmann.devel@googlemail.com> 3 * 4 * based on previous work by 5 * 6 * Ulf Samuelsson <ulf@atmel.com> 7 * Rick Bronson <rick@efn.org> 8 * 9 * Configuration settings for the AT91RM9200EK board. 10 * 11 * SPDX-License-Identifier: GPL-2.0+ 12 */ 13 14 #ifndef __AT91RM9200EK_CONFIG_H__ 15 #define __AT91RM9200EK_CONFIG_H__ 16 17 #include <linux/sizes.h> 18 19 /* 20 * set some initial configurations depending on configure target 21 * 22 * at91rm9200ek_config -> boot from 0x0 in NOR Flash at CS0 23 * at91rm9200ek_ram_config -> continue booting from 0x20100000 in RAM; lowlevel 24 * initialisation was done by some preloader 25 */ 26 #ifdef CONFIG_RAMBOOT 27 #define CONFIG_SKIP_LOWLEVEL_INIT 28 #endif 29 30 /* 31 * AT91C_XTAL_CLOCK is the frequency of external xtal in hertz 32 * AT91C_MAIN_CLOCK is the frequency of PLLA output 33 * AT91C_MASTER_CLOCK is the peripherial clock 34 * CONFIG_SYS_HZ_CLOCK is the value for CCR in tc0 (divider 2 is implicitely 35 * set in arch/arm/cpu/arm920t/at91/timer.c) 36 * CONFIG_SYS_HZ is the tick rate for timer tc0 37 */ 38 #define AT91C_XTAL_CLOCK 18432000 39 #define CONFIG_SYS_AT91_SLOW_CLOCK 32768 40 #define AT91C_MAIN_CLOCK ((AT91C_XTAL_CLOCK / 4) * 39) 41 #define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3 ) 42 #define CONFIG_SYS_HZ_CLOCK (AT91C_MASTER_CLOCK / 2) 43 44 /* CPU configuration */ 45 #define CONFIG_AT91RM9200 46 #define CONFIG_AT91RM9200EK 47 #define CONFIG_CPUAT91 48 #define USE_920T_MMU 49 50 #include <asm/hardware.h> /* needed for port definitions */ 51 52 #define CONFIG_CMDLINE_TAG 53 #define CONFIG_SETUP_MEMORY_TAGS 54 #define CONFIG_INITRD_TAG 55 56 /* 57 * Memory Configuration 58 */ 59 #define CONFIG_NR_DRAM_BANKS 1 60 #define CONFIG_SYS_SDRAM_BASE 0x20000000 61 #define CONFIG_SYS_SDRAM_SIZE SZ_32M 62 63 #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE 64 #define CONFIG_SYS_MEMTEST_END \ 65 (CONFIG_SYS_MEMTEST_START + CONFIG_SYS_SDRAM_SIZE - SZ_256K) 66 67 /* 68 * LowLevel Init 69 */ 70 #ifndef CONFIG_SKIP_LOWLEVEL_INIT 71 #define CONFIG_SYS_USE_MAIN_OSCILLATOR 72 /* flash */ 73 #define CONFIG_SYS_EBI_CFGR_VAL 0x00000000 74 #define CONFIG_SYS_SMC_CSR0_VAL 0x00003284 /* 16bit, 2 TDF, 4 WS */ 75 76 /* clocks */ 77 #define CONFIG_SYS_PLLAR_VAL 0x20263E04 /* 179.712000 MHz for PCK */ 78 #define CONFIG_SYS_PLLBR_VAL 0x10483E0E /* 48.054857 MHz (divider by 2 for USB) */ 79 /* PCK/3 = MCK Master Clock = 59.904000MHz from PLLA */ 80 #define CONFIG_SYS_MCKR_VAL 0x00000202 81 82 /* sdram */ 83 #define CONFIG_SYS_PIOC_ASR_VAL 0xFFFF0000 /* Configure PIOC as peripheral (D16/D31) */ 84 #define CONFIG_SYS_PIOC_BSR_VAL 0x00000000 85 #define CONFIG_SYS_PIOC_PDR_VAL 0xFFFF0000 86 #define CONFIG_SYS_EBI_CSA_VAL 0x00000002 /* CS1=CONFIG_SYS_SDRAM */ 87 #define CONFIG_SYS_SDRC_CR_VAL 0x2188c155 /* set up the CONFIG_SYS_SDRAM */ 88 #define CONFIG_SYS_SDRAM CONFIG_SYS_SDRAM_BASE /* address of the SDRAM */ 89 #define CONFIG_SYS_SDRAM1 (CONFIG_SYS_SDRAM_BASE+0x80) 90 #define CONFIG_SYS_SDRAM_VAL 0x00000000 /* value written to CONFIG_SYS_SDRAM */ 91 #define CONFIG_SYS_SDRC_MR_VAL 0x00000002 /* Precharge All */ 92 #define CONFIG_SYS_SDRC_MR_VAL1 0x00000004 /* refresh */ 93 #define CONFIG_SYS_SDRC_MR_VAL2 0x00000003 /* Load Mode Register */ 94 #define CONFIG_SYS_SDRC_MR_VAL3 0x00000000 /* Normal Mode */ 95 #define CONFIG_SYS_SDRC_TR_VAL 0x000002E0 /* Write refresh rate */ 96 #endif /* CONFIG_SKIP_LOWLEVEL_INIT */ 97 98 /* 99 * Hardware drivers 100 */ 101 /* 102 * Choose a USART for serial console 103 * CONFIG_DBGU is DBGU unit on J10 104 * CONFIG_USART1 is USART1 on J14 105 */ 106 #define CONFIG_ATMEL_USART 107 #define CONFIG_USART_BASE ATMEL_BASE_DBGU 108 #define CONFIG_USART_ID 0/* ignored in arm */ 109 110 /* 111 * Command line configuration. 112 */ 113 114 /* 115 * Network Driver Setting 116 */ 117 #define CONFIG_DRIVER_AT91EMAC 118 #define CONFIG_SYS_RX_ETH_BUFFER 16 119 #define CONFIG_RMII 120 #define CONFIG_MII 121 122 /* 123 * NOR Flash 124 */ 125 #define CONFIG_FLASH_CFI_DRIVER 126 #define CONFIG_SYS_FLASH_CFI 127 #define CONFIG_SYS_FLASH_BASE 0x10000000 128 #define PHYS_FLASH_1 CONFIG_SYS_FLASH_BASE 129 #define PHYS_FLASH_SIZE SZ_8M 130 #define CONFIG_SYS_MAX_FLASH_BANKS 1 131 #define CONFIG_SYS_MAX_FLASH_SECT 256 132 #define CONFIG_SYS_FLASH_PROTECTION 133 134 /* 135 * USB Config 136 */ 137 #define CONFIG_USB_ATMEL 1 138 #define CONFIG_USB_ATMEL_CLK_SEL_PLLB 139 #define CONFIG_USB_OHCI_NEW 1 140 141 #define CONFIG_SYS_USB_OHCI_CPU_INIT 1 142 #define CONFIG_SYS_USB_OHCI_REGS_BASE ATMEL_USB_HOST_BASE 143 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91rm9200" 144 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 145 146 /* 147 * Environment Settings 148 */ 149 150 /* 151 * after u-boot.bin 152 */ 153 #define CONFIG_ENV_ADDR \ 154 (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) 155 #define CONFIG_ENV_SIZE SZ_64K /* sectors are 64K here */ 156 /* The following #defines are needed to get flash environment right */ 157 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE 158 #define CONFIG_SYS_MONITOR_LEN SZ_256K 159 160 /* 161 * Boot option 162 */ 163 164 /* default load address */ 165 #define CONFIG_SYS_LOAD_ADDR CONFIG_SYS_SDRAM_BASE + SZ_16M 166 #define CONFIG_ENV_OVERWRITE 167 168 /* 169 * Shell Settings 170 */ 171 172 /* 173 * Size of malloc() pool 174 */ 175 #define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + SZ_128K, \ 176 SZ_4K) 177 178 #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + SZ_4K \ 179 - GENERATED_GBL_DATA_SIZE) 180 181 #endif /* __AT91RM9200EK_CONFIG_H__ */ 182