1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2006, 2010-2011 Freescale Semiconductor. 4 * 5 * Srikanth Srinivasan (srikanth.srinivasan@freescale.com) 6 */ 7 8 /* 9 * MPC8641HPCN board configuration file 10 * 11 * Make sure you change the MAC address and other network params first, 12 * search for CONFIG_SERVERIP, etc. in this file. 13 */ 14 15 #ifndef __CONFIG_H 16 #define __CONFIG_H 17 18 /* High Level Configuration Options */ 19 #define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */ 20 #define CONFIG_ADDR_MAP 1 /* Use addr map */ 21 22 /* 23 * default CCSRBAR is at 0xff700000 24 * assume U-Boot is less than 0.5MB 25 */ 26 27 #ifdef RUN_DIAG 28 #define CONFIG_SYS_DIAG_ADDR CONFIG_SYS_FLASH_BASE 29 #endif 30 31 /* 32 * virtual address to be used for temporary mappings. There 33 * should be 128k free at this VA. 34 */ 35 #define CONFIG_SYS_SCRATCH_VA 0xe0000000 36 37 #define CONFIG_SYS_SRIO 38 #define CONFIG_SRIO1 /* SRIO port 1 */ 39 40 #define CONFIG_PCIE1 1 /* PCIE controller 1 (ULI bridge) */ 41 #define CONFIG_PCIE2 1 /* PCIE controller 2 (slot) */ 42 #define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */ 43 #define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */ 44 45 #define CONFIG_ENV_OVERWRITE 46 47 #define CONFIG_BAT_RW 1 /* Use common BAT rw code */ 48 #define CONFIG_HIGH_BATS 1 /* High BATs supported and enabled */ 49 #define CONFIG_SYS_NUM_ADDR_MAP 8 /* Number of addr map slots = 8 dbats */ 50 51 #define CONFIG_ALTIVEC 1 52 53 /* 54 * L2CR setup -- make sure this is right for your board! 55 */ 56 #define CONFIG_SYS_L2 57 #define L2_INIT 0 58 #define L2_ENABLE (L2CR_L2E) 59 60 #ifndef CONFIG_SYS_CLK_FREQ 61 #ifndef __ASSEMBLY__ 62 extern unsigned long get_board_sys_clk(unsigned long dummy); 63 #endif 64 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) 65 #endif 66 67 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest region */ 68 #define CONFIG_SYS_MEMTEST_END 0x00400000 69 70 /* 71 * With the exception of PCI Memory and Rapid IO, most devices will simply 72 * add CONFIG_SYS_PHYS_ADDR_HIGH to the front of the 32-bit VA to get the PA 73 * when 36-bit is enabled. When 36-bit is not enabled, these bits are 0. 74 */ 75 #ifdef CONFIG_PHYS_64BIT 76 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x0000000f 77 #else 78 #define CONFIG_SYS_PHYS_ADDR_HIGH 0x00000000 79 #endif 80 81 /* 82 * Base addresses -- Note these are effective addresses where the 83 * actual resources get mapped (not physical addresses) 84 */ 85 #define CONFIG_SYS_CCSRBAR 0xffe00000 /* relocated CCSRBAR */ 86 #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */ 87 88 /* Physical addresses */ 89 #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR 90 #define CONFIG_SYS_CCSRBAR_PHYS_HIGH CONFIG_SYS_PHYS_ADDR_HIGH 91 #define CONFIG_SYS_CCSRBAR_PHYS \ 92 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 93 CONFIG_SYS_CCSRBAR_PHYS_HIGH) 94 95 #define CONFIG_HWCONFIG /* use hwconfig to control memory interleaving */ 96 97 /* 98 * DDR Setup 99 */ 100 #define CONFIG_FSL_DDR_INTERACTIVE 101 #define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */ 102 #define CONFIG_DDR_SPD 103 104 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */ 105 #define CONFIG_MEM_INIT_VALUE 0xDeadBeef 106 107 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/ 108 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 109 #define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */ 110 #define CONFIG_VERY_BIG_RAM 111 112 #define CONFIG_DIMM_SLOTS_PER_CTLR 2 113 #define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR) 114 115 /* 116 * I2C addresses of SPD EEPROMs 117 */ 118 #define SPD_EEPROM_ADDRESS1 0x51 /* CTLR 0 DIMM 0 */ 119 #define SPD_EEPROM_ADDRESS2 0x52 /* CTLR 0 DIMM 1 */ 120 #define SPD_EEPROM_ADDRESS3 0x53 /* CTLR 1 DIMM 0 */ 121 #define SPD_EEPROM_ADDRESS4 0x54 /* CTLR 1 DIMM 1 */ 122 123 /* 124 * These are used when DDR doesn't use SPD. 125 */ 126 #define CONFIG_SYS_SDRAM_SIZE 256 /* DDR is 256MB */ 127 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000F 128 #define CONFIG_SYS_DDR_CS0_CONFIG 0x80010102 /* Enable, no interleaving */ 129 #define CONFIG_SYS_DDR_TIMING_3 0x00000000 130 #define CONFIG_SYS_DDR_TIMING_0 0x00260802 131 #define CONFIG_SYS_DDR_TIMING_1 0x39357322 132 #define CONFIG_SYS_DDR_TIMING_2 0x14904cc8 133 #define CONFIG_SYS_DDR_MODE_1 0x00480432 134 #define CONFIG_SYS_DDR_MODE_2 0x00000000 135 #define CONFIG_SYS_DDR_INTERVAL 0x06090100 136 #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef 137 #define CONFIG_SYS_DDR_CLK_CTRL 0x03800000 138 #define CONFIG_SYS_DDR_OCD_CTRL 0x00000000 139 #define CONFIG_SYS_DDR_OCD_STATUS 0x00000000 140 #define CONFIG_SYS_DDR_CONTROL 0xe3008000 /* Type = DDR2 */ 141 #define CONFIG_SYS_DDR_CONTROL2 0x04400000 142 143 #define CONFIG_ID_EEPROM 144 #define CONFIG_SYS_I2C_EEPROM_NXID 145 #define CONFIG_ID_EEPROM 146 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 147 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 148 149 #define CONFIG_SYS_FLASH_BASE 0xef800000 /* start of FLASH 8M */ 150 #define CONFIG_SYS_FLASH_BASE_PHYS_LOW CONFIG_SYS_FLASH_BASE 151 #define CONFIG_SYS_FLASH_BASE_PHYS \ 152 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 153 CONFIG_SYS_PHYS_ADDR_HIGH) 154 155 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} 156 157 #define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ 158 | 0x00001001) /* port size 16bit */ 159 #define CONFIG_SYS_OR0_PRELIM 0xff806ff7 /* 8MB Boot Flash area*/ 160 161 #define CONFIG_SYS_BR2_PRELIM (BR_PHYS_ADDR(CF_BASE_PHYS) \ 162 | 0x00001001) /* port size 16bit */ 163 #define CONFIG_SYS_OR2_PRELIM 0xffffeff7 /* 32k Compact Flash */ 164 165 #define CONFIG_SYS_BR3_PRELIM (BR_PHYS_ADDR(PIXIS_BASE_PHYS) \ 166 | 0x00000801) /* port size 8bit */ 167 #define CONFIG_SYS_OR3_PRELIM 0xffffeff7 /* 32k PIXIS area*/ 168 169 /* 170 * The LBC_BASE is the base of the region that contains the PIXIS and the CF. 171 * The PIXIS and CF by themselves aren't large enough to take up the 128k 172 * required for the smallest BAT mapping, so there's a 64k hole. 173 */ 174 #define CONFIG_SYS_LBC_BASE 0xffde0000 175 #define CONFIG_SYS_LBC_BASE_PHYS_LOW CONFIG_SYS_LBC_BASE 176 177 #define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */ 178 #define PIXIS_BASE (CONFIG_SYS_LBC_BASE + 0x00010000) 179 #define PIXIS_BASE_PHYS_LOW (CONFIG_SYS_LBC_BASE_PHYS_LOW + 0x00010000) 180 #define PIXIS_BASE_PHYS PAIRED_PHYS_TO_PHYS(PIXIS_BASE_PHYS_LOW, \ 181 CONFIG_SYS_PHYS_ADDR_HIGH) 182 #define PIXIS_SIZE 0x00008000 /* 32k */ 183 #define PIXIS_ID 0x0 /* Board ID at offset 0 */ 184 #define PIXIS_VER 0x1 /* Board version at offset 1 */ 185 #define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */ 186 #define PIXIS_RST 0x4 /* PIXIS Reset Control register */ 187 #define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch register */ 188 #define PIXIS_SPD 0x7 /* Register for SYSCLK speed */ 189 #define PIXIS_VCTL 0x10 /* VELA Control Register */ 190 #define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */ 191 #define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */ 192 #define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */ 193 #define PIXIS_VBOOT_FMAP 0x80 /* VBOOT - CFG_FLASHMAP */ 194 #define PIXIS_VBOOT_FBANK 0x40 /* VBOOT - CFG_FLASHBANK */ 195 #define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */ 196 #define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */ 197 #define PIXIS_VCLKH 0x19 /* VELA VCLKH register */ 198 #define PIXIS_VCLKL 0x1A /* VELA VCLKL register */ 199 #define CONFIG_SYS_PIXIS_VBOOT_MASK 0x40 /* Reset altbank mask*/ 200 201 /* Compact flash shares a BAT with PIXIS; make sure they're contiguous */ 202 #define CF_BASE (PIXIS_BASE + PIXIS_SIZE) 203 #define CF_BASE_PHYS (PIXIS_BASE_PHYS + PIXIS_SIZE) 204 205 #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ 206 #define CONFIG_SYS_MAX_FLASH_SECT 128 /* sectors per device */ 207 208 #undef CONFIG_SYS_FLASH_CHECKSUM 209 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 210 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 211 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 212 #define CONFIG_SYS_MONITOR_BASE_EARLY 0xfff00000 /* early monitor loc */ 213 214 #define CONFIG_FLASH_CFI_DRIVER 215 #define CONFIG_SYS_FLASH_CFI 216 #define CONFIG_SYS_FLASH_EMPTY_INFO 217 218 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE) 219 #define CONFIG_SYS_RAMBOOT 220 #else 221 #undef CONFIG_SYS_RAMBOOT 222 #endif 223 224 #if defined(CONFIG_SYS_RAMBOOT) 225 #undef CONFIG_SPD_EEPROM 226 #define CONFIG_SYS_SDRAM_SIZE 256 227 #endif 228 229 #undef CONFIG_CLOCKS_IN_MHZ 230 231 #define CONFIG_SYS_INIT_RAM_LOCK 1 232 #ifndef CONFIG_SYS_INIT_RAM_LOCK 233 #define CONFIG_SYS_INIT_RAM_ADDR 0x0fd00000 /* Initial RAM address */ 234 #else 235 #define CONFIG_SYS_INIT_RAM_ADDR 0xf8400000 /* Initial RAM address */ 236 #endif 237 #define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in RAM */ 238 239 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) 240 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 241 242 #define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ 243 #define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */ 244 245 /* Serial Port */ 246 #define CONFIG_SYS_NS16550_SERIAL 247 #define CONFIG_SYS_NS16550_REG_SIZE 1 248 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) 249 250 #define CONFIG_SYS_BAUDRATE_TABLE \ 251 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200} 252 253 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500) 254 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600) 255 256 /* 257 * I2C 258 */ 259 #define CONFIG_SYS_I2C 260 #define CONFIG_SYS_I2C_FSL 261 #define CONFIG_SYS_FSL_I2C_SPEED 400000 262 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 263 #define CONFIG_SYS_FSL_I2C_OFFSET 0x3100 264 #define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } 265 266 /* 267 * RapidIO MMU 268 */ 269 #define CONFIG_SYS_SRIO1_MEM_BASE 0x80000000 /* base address */ 270 #ifdef CONFIG_PHYS_64BIT 271 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW 0x00000000 272 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x0000000c 273 #else 274 #define CONFIG_SYS_SRIO1_MEM_PHYS_LOW CONFIG_SYS_SRIO1_MEM_BASE 275 #define CONFIG_SYS_SRIO1_MEM_PHYS_HIGH 0x00000000 276 #endif 277 #define CONFIG_SYS_SRIO1_MEM_PHYS \ 278 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 279 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) 280 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */ 281 282 /* 283 * General PCI 284 * Addresses are mapped 1-1. 285 */ 286 287 #define CONFIG_SYS_PCIE1_NAME "ULI" 288 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 289 #ifdef CONFIG_PHYS_64BIT 290 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 291 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW 0x00000000 292 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x0000000c 293 #else 294 #define CONFIG_SYS_PCIE1_MEM_BUS CONFIG_SYS_PCIE1_MEM_VIRT 295 #define CONFIG_SYS_PCIE1_MEM_PHYS_LOW CONFIG_SYS_PCIE1_MEM_VIRT 296 #define CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 0x00000000 297 #endif 298 #define CONFIG_SYS_PCIE1_MEM_PHYS \ 299 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 300 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) 301 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 302 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 303 #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 304 #define CONFIG_SYS_PCIE1_IO_PHYS_LOW CONFIG_SYS_PCIE1_IO_VIRT 305 #define CONFIG_SYS_PCIE1_IO_PHYS \ 306 PAIRED_PHYS_TO_PHYS(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 307 CONFIG_SYS_PHYS_ADDR_HIGH) 308 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64K */ 309 310 #ifdef CONFIG_PHYS_64BIT 311 /* 312 * Use the same PCI bus address on PCIE1 and PCIE2 if we have PHYS_64BIT. 313 * This will increase the amount of PCI address space available for 314 * for mapping RAM. 315 */ 316 #define CONFIG_SYS_PCIE2_MEM_BUS CONFIG_SYS_PCIE1_MEM_BUS 317 #else 318 #define CONFIG_SYS_PCIE2_MEM_BUS (CONFIG_SYS_PCIE1_MEM_BUS \ 319 + CONFIG_SYS_PCIE1_MEM_SIZE) 320 #endif 321 #define CONFIG_SYS_PCIE2_MEM_VIRT (CONFIG_SYS_PCIE1_MEM_VIRT \ 322 + CONFIG_SYS_PCIE1_MEM_SIZE) 323 #define CONFIG_SYS_PCIE2_MEM_PHYS_LOW (CONFIG_SYS_PCIE1_MEM_PHYS_LOW \ 324 + CONFIG_SYS_PCIE1_MEM_SIZE) 325 #define CONFIG_SYS_PCIE2_MEM_PHYS_HIGH CONFIG_SYS_PCIE1_MEM_PHYS_HIGH 326 #define CONFIG_SYS_PCIE2_MEM_PHYS (CONFIG_SYS_PCIE1_MEM_PHYS \ 327 + CONFIG_SYS_PCIE1_MEM_SIZE) 328 #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ 329 #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 330 #define CONFIG_SYS_PCIE2_IO_VIRT (CONFIG_SYS_PCIE1_IO_VIRT \ 331 + CONFIG_SYS_PCIE1_IO_SIZE) 332 #define CONFIG_SYS_PCIE2_IO_PHYS_LOW (CONFIG_SYS_PCIE1_IO_PHYS_LOW \ 333 + CONFIG_SYS_PCIE1_IO_SIZE) 334 #define CONFIG_SYS_PCIE2_IO_PHYS (CONFIG_SYS_PCIE1_IO_PHYS \ 335 + CONFIG_SYS_PCIE1_IO_SIZE) 336 #define CONFIG_SYS_PCIE2_IO_SIZE CONFIG_SYS_PCIE1_IO_SIZE 337 338 #if defined(CONFIG_PCI) 339 340 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 341 342 #undef CONFIG_EEPRO100 343 #undef CONFIG_TULIP 344 345 /************************************************************ 346 * USB support 347 ************************************************************/ 348 #define CONFIG_PCI_OHCI 1 349 #define CONFIG_USB_OHCI_NEW 1 350 #define CONFIG_SYS_USB_OHCI_SLOT_NAME "ohci_pci" 351 #define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15 352 #define CONFIG_SYS_OHCI_SWAP_REG_ACCESS 1 353 354 /*PCIE video card used*/ 355 #define VIDEO_IO_OFFSET CONFIG_SYS_PCIE2_IO_VIRT 356 357 /*PCI video card used*/ 358 /*#define VIDEO_IO_OFFSET CONFIG_SYS_PCIE1_IO_VIRT*/ 359 360 /* video */ 361 362 #if defined(CONFIG_VIDEO) 363 #define CONFIG_BIOSEMU 364 #define CONFIG_ATI_RADEON_FB 365 #define CONFIG_VIDEO_LOGO 366 #define CONFIG_SYS_ISA_IO_BASE_ADDRESS CONFIG_SYS_PCIE2_IO_VIRT 367 #endif 368 369 #undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 370 371 #ifdef CONFIG_SCSI_AHCI 372 #define CONFIG_SATA_ULI5288 373 #define CONFIG_SYS_SCSI_MAX_SCSI_ID 4 374 #define CONFIG_SYS_SCSI_MAX_LUN 1 375 #define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN) 376 #define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE 377 #endif 378 379 #endif /* CONFIG_PCI */ 380 381 #if defined(CONFIG_TSEC_ENET) 382 #define CONFIG_TSEC1 1 383 #define CONFIG_TSEC1_NAME "eTSEC1" 384 #define CONFIG_TSEC2 1 385 #define CONFIG_TSEC2_NAME "eTSEC2" 386 #define CONFIG_TSEC3 1 387 #define CONFIG_TSEC3_NAME "eTSEC3" 388 #define CONFIG_TSEC4 1 389 #define CONFIG_TSEC4_NAME "eTSEC4" 390 391 #define TSEC1_PHY_ADDR 0 392 #define TSEC2_PHY_ADDR 1 393 #define TSEC3_PHY_ADDR 2 394 #define TSEC4_PHY_ADDR 3 395 #define TSEC1_PHYIDX 0 396 #define TSEC2_PHYIDX 0 397 #define TSEC3_PHYIDX 0 398 #define TSEC4_PHYIDX 0 399 #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 400 #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 401 #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 402 #define TSEC4_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) 403 404 #define CONFIG_ETHPRIME "eTSEC1" 405 406 #endif /* CONFIG_TSEC_ENET */ 407 408 #ifdef CONFIG_PHYS_64BIT 409 #define PHYS_HIGH_TO_BXPN(x) ((x & 0x0000000e) << 8) 410 #define PHYS_HIGH_TO_BX(x) ((x & 0x00000001) << 2) 411 412 /* Put physical address into the BAT format */ 413 #define BAT_PHYS_ADDR(low, high) \ 414 (low | PHYS_HIGH_TO_BXPN(high) | PHYS_HIGH_TO_BX(high)) 415 /* Convert high/low pairs to actual 64-bit value */ 416 #define PAIRED_PHYS_TO_PHYS(low, high) (low | ((u64)high << 32)) 417 #else 418 /* 32-bit systems just ignore the "high" bits */ 419 #define BAT_PHYS_ADDR(low, high) (low) 420 #define PAIRED_PHYS_TO_PHYS(low, high) (low) 421 #endif 422 423 /* 424 * BAT0 DDR 425 */ 426 #define CONFIG_SYS_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 427 #define CONFIG_SYS_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE) 428 429 /* 430 * BAT1 LBC (PIXIS/CF) 431 */ 432 #define CONFIG_SYS_DBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 433 CONFIG_SYS_PHYS_ADDR_HIGH) \ 434 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 435 BATL_GUARDEDSTORAGE) 436 #define CONFIG_SYS_DBAT1U (CONFIG_SYS_LBC_BASE | BATU_BL_128K \ 437 | BATU_VS | BATU_VP) 438 #define CONFIG_SYS_IBAT1L (BAT_PHYS_ADDR(CONFIG_SYS_LBC_BASE_PHYS_LOW, \ 439 CONFIG_SYS_PHYS_ADDR_HIGH) \ 440 | BATL_PP_RW | BATL_MEMCOHERENCE) 441 #define CONFIG_SYS_IBAT1U CONFIG_SYS_DBAT1U 442 443 /* if CONFIG_PCI: 444 * BAT2 PCIE1 and PCIE1 MEM 445 * if CONFIG_RIO 446 * BAT2 Rapidio Memory 447 */ 448 #ifdef CONFIG_PCI 449 #define CONFIG_PCI_INDIRECT_BRIDGE 450 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 451 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 452 | BATL_PP_RW | BATL_CACHEINHIBIT \ 453 | BATL_GUARDEDSTORAGE) 454 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_PCIE1_MEM_VIRT | BATU_BL_1G \ 455 | BATU_VS | BATU_VP) 456 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_MEM_PHYS_LOW, \ 457 CONFIG_SYS_PCIE1_MEM_PHYS_HIGH) \ 458 | BATL_PP_RW | BATL_CACHEINHIBIT) 459 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 460 #else /* CONFIG_RIO */ 461 #define CONFIG_SYS_DBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 462 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 463 | BATL_PP_RW | BATL_CACHEINHIBIT | \ 464 BATL_GUARDEDSTORAGE) 465 #define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M \ 466 | BATU_VS | BATU_VP) 467 #define CONFIG_SYS_IBAT2L (BAT_PHYS_ADDR(CONFIG_SYS_SRIO1_MEM_PHYS_LOW, \ 468 CONFIG_SYS_SRIO1_MEM_PHYS_HIGH) \ 469 | BATL_PP_RW | BATL_CACHEINHIBIT) 470 #define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U 471 #endif 472 473 /* 474 * BAT3 CCSR Space 475 */ 476 #define CONFIG_SYS_DBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 477 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 478 | BATL_PP_RW | BATL_CACHEINHIBIT \ 479 | BATL_GUARDEDSTORAGE) 480 #define CONFIG_SYS_DBAT3U (CONFIG_SYS_CCSRBAR | BATU_BL_1M | BATU_VS \ 481 | BATU_VP) 482 #define CONFIG_SYS_IBAT3L (BAT_PHYS_ADDR(CONFIG_SYS_CCSRBAR_PHYS_LOW, \ 483 CONFIG_SYS_CCSRBAR_PHYS_HIGH) \ 484 | BATL_PP_RW | BATL_CACHEINHIBIT) 485 #define CONFIG_SYS_IBAT3U CONFIG_SYS_DBAT3U 486 487 #if (CONFIG_SYS_CCSRBAR_DEFAULT != CONFIG_SYS_CCSRBAR) 488 #define CONFIG_SYS_CCSR_DEFAULT_DBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 489 | BATL_PP_RW | BATL_CACHEINHIBIT \ 490 | BATL_GUARDEDSTORAGE) 491 #define CONFIG_SYS_CCSR_DEFAULT_DBATU (CONFIG_SYS_CCSRBAR_DEFAULT \ 492 | BATU_BL_1M | BATU_VS | BATU_VP) 493 #define CONFIG_SYS_CCSR_DEFAULT_IBATL (CONFIG_SYS_CCSRBAR_DEFAULT \ 494 | BATL_PP_RW | BATL_CACHEINHIBIT) 495 #define CONFIG_SYS_CCSR_DEFAULT_IBATU CONFIG_SYS_CCSR_DEFAULT_DBATU 496 #endif 497 498 /* 499 * BAT4 PCIE1_IO and PCIE2_IO 500 */ 501 #define CONFIG_SYS_DBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 502 CONFIG_SYS_PHYS_ADDR_HIGH) \ 503 | BATL_PP_RW | BATL_CACHEINHIBIT \ 504 | BATL_GUARDEDSTORAGE) 505 #define CONFIG_SYS_DBAT4U (CONFIG_SYS_PCIE1_IO_VIRT | BATU_BL_128K \ 506 | BATU_VS | BATU_VP) 507 #define CONFIG_SYS_IBAT4L (BAT_PHYS_ADDR(CONFIG_SYS_PCIE1_IO_PHYS_LOW, \ 508 CONFIG_SYS_PHYS_ADDR_HIGH) \ 509 | BATL_PP_RW | BATL_CACHEINHIBIT) 510 #define CONFIG_SYS_IBAT4U CONFIG_SYS_DBAT4U 511 512 /* 513 * BAT5 Init RAM for stack in the CPU DCache (no backing memory) 514 */ 515 #define CONFIG_SYS_DBAT5L (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE) 516 #define CONFIG_SYS_DBAT5U (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP) 517 #define CONFIG_SYS_IBAT5L CONFIG_SYS_DBAT5L 518 #define CONFIG_SYS_IBAT5U CONFIG_SYS_DBAT5U 519 520 /* 521 * BAT6 FLASH 522 */ 523 #define CONFIG_SYS_DBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 524 CONFIG_SYS_PHYS_ADDR_HIGH) \ 525 | BATL_PP_RW | BATL_CACHEINHIBIT \ 526 | BATL_GUARDEDSTORAGE) 527 #define CONFIG_SYS_DBAT6U (CONFIG_SYS_FLASH_BASE | BATU_BL_8M | BATU_VS \ 528 | BATU_VP) 529 #define CONFIG_SYS_IBAT6L (BAT_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_LOW, \ 530 CONFIG_SYS_PHYS_ADDR_HIGH) \ 531 | BATL_PP_RW | BATL_MEMCOHERENCE) 532 #define CONFIG_SYS_IBAT6U CONFIG_SYS_DBAT6U 533 534 /* Map the last 1M of flash where we're running from reset */ 535 #define CONFIG_SYS_DBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 536 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE) 537 #define CONFIG_SYS_DBAT6U_EARLY (CONFIG_SYS_TEXT_BASE | BATU_BL_1M | BATU_VS | BATU_VP) 538 #define CONFIG_SYS_IBAT6L_EARLY (CONFIG_SYS_MONITOR_BASE_EARLY | BATL_PP_RW \ 539 | BATL_MEMCOHERENCE) 540 #define CONFIG_SYS_IBAT6U_EARLY CONFIG_SYS_DBAT6U_EARLY 541 542 /* 543 * BAT7 FREE - used later for tmp mappings 544 */ 545 #define CONFIG_SYS_DBAT7L 0x00000000 546 #define CONFIG_SYS_DBAT7U 0x00000000 547 #define CONFIG_SYS_IBAT7L 0x00000000 548 #define CONFIG_SYS_IBAT7U 0x00000000 549 550 /* 551 * Environment 552 */ 553 #ifndef CONFIG_SYS_RAMBOOT 554 #define CONFIG_ENV_ADDR \ 555 (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN) 556 #define CONFIG_ENV_SECT_SIZE 0x10000 /* 64K(one sector) for env */ 557 #else 558 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) 559 #endif 560 #define CONFIG_ENV_SIZE 0x2000 561 562 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ 563 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ 564 565 /* 566 * BOOTP options 567 */ 568 #define CONFIG_BOOTP_BOOTFILESIZE 569 570 #undef CONFIG_WATCHDOG /* watchdog disabled */ 571 572 /* 573 * Miscellaneous configurable options 574 */ 575 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 576 577 /* 578 * For booting Linux, the board info and command line data 579 * have to be in the first 8 MB of memory, since this is 580 * the maximum mapped by the Linux kernel during initialization. 581 */ 582 #define CONFIG_SYS_BOOTMAPSZ (256 << 20) /* Initial Memory map for Linux*/ 583 #define CONFIG_SYS_BOOTM_LEN (256 << 20) /* Increase max gunzip size */ 584 585 #if defined(CONFIG_CMD_KGDB) 586 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 587 #endif 588 589 /* 590 * Environment Configuration 591 */ 592 593 #define CONFIG_HAS_ETH0 1 594 #define CONFIG_HAS_ETH1 1 595 #define CONFIG_HAS_ETH2 1 596 #define CONFIG_HAS_ETH3 1 597 598 #define CONFIG_IPADDR 192.168.1.100 599 600 #define CONFIG_HOSTNAME "unknown" 601 #define CONFIG_ROOTPATH "/opt/nfsroot" 602 #define CONFIG_BOOTFILE "uImage" 603 #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ 604 605 #define CONFIG_SERVERIP 192.168.1.1 606 #define CONFIG_GATEWAYIP 192.168.1.1 607 #define CONFIG_NETMASK 255.255.255.0 608 609 /* default location for tftp and bootm */ 610 #define CONFIG_LOADADDR 0x10000000 611 612 #define CONFIG_EXTRA_ENV_SETTINGS \ 613 "netdev=eth0\0" \ 614 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 615 "tftpflash=tftpboot $loadaddr $uboot; " \ 616 "protect off " __stringify(CONFIG_SYS_TEXT_BASE) \ 617 " +$filesize; " \ 618 "erase " __stringify(CONFIG_SYS_TEXT_BASE) \ 619 " +$filesize; " \ 620 "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 621 " $filesize; " \ 622 "protect on " __stringify(CONFIG_SYS_TEXT_BASE) \ 623 " +$filesize; " \ 624 "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE) \ 625 " $filesize\0" \ 626 "consoledev=ttyS0\0" \ 627 "ramdiskaddr=0x18000000\0" \ 628 "ramdiskfile=your.ramdisk.u-boot\0" \ 629 "fdtaddr=0x17c00000\0" \ 630 "fdtfile=mpc8641_hpcn.dtb\0" \ 631 "en-wd=mw.b ffdf0010 0x08; echo -expect:- 08; md.b ffdf0010 1\0" \ 632 "dis-wd=mw.b ffdf0010 0x00; echo -expect:- 00; md.b ffdf0010 1\0" \ 633 "maxcpus=2" 634 635 #define CONFIG_NFSBOOTCOMMAND \ 636 "setenv bootargs root=/dev/nfs rw " \ 637 "nfsroot=$serverip:$rootpath " \ 638 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 639 "console=$consoledev,$baudrate $othbootargs;" \ 640 "tftp $loadaddr $bootfile;" \ 641 "tftp $fdtaddr $fdtfile;" \ 642 "bootm $loadaddr - $fdtaddr" 643 644 #define CONFIG_RAMBOOTCOMMAND \ 645 "setenv bootargs root=/dev/ram rw " \ 646 "console=$consoledev,$baudrate $othbootargs;" \ 647 "tftp $ramdiskaddr $ramdiskfile;" \ 648 "tftp $loadaddr $bootfile;" \ 649 "tftp $fdtaddr $fdtfile;" \ 650 "bootm $loadaddr $ramdiskaddr $fdtaddr" 651 652 #define CONFIG_BOOTCOMMAND CONFIG_NFSBOOTCOMMAND 653 654 #endif /* __CONFIG_H */ 655