1 /* SPDX-License-Identifier: GPL-2.0+ */ 2 /* 3 * Copyright 2011-2012 Freescale Semiconductor, Inc. 4 */ 5 6 #ifndef __CONFIG_H 7 #define __CONFIG_H 8 9 /* 10 * B4860 QDS board configuration file 11 */ 12 #ifdef CONFIG_RAMBOOT_PBL 13 #define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/b4860qds/b4_pbi.cfg 14 #define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/b4860qds/b4_rcw.cfg 15 #ifndef CONFIG_NAND 16 #define CONFIG_RAMBOOT_TEXT_BASE CONFIG_SYS_TEXT_BASE 17 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 18 #else 19 #define CONFIG_SPL_FLUSH_IMAGE 20 #define CONFIG_SPL_TEXT_BASE 0xFFFD8000 21 #define CONFIG_SPL_PAD_TO 0x40000 22 #define CONFIG_SPL_MAX_SIZE 0x28000 23 #define RESET_VECTOR_OFFSET 0x27FFC 24 #define BOOT_PAGE_OFFSET 0x27000 25 #define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10) 26 #define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000 27 #define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 28 #define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) 29 #define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" 30 #define CONFIG_SPL_NAND_BOOT 31 #ifdef CONFIG_SPL_BUILD 32 #define CONFIG_SPL_SKIP_RELOCATE 33 #define CONFIG_SPL_COMMON_INIT_DDR 34 #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE 35 #endif 36 #endif 37 #endif 38 39 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 40 /* Set 1M boot space */ 41 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) 42 #define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ 43 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) 44 #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc 45 #endif 46 47 /* High Level Configuration Options */ 48 #define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */ 49 50 #ifndef CONFIG_RESET_VECTOR_ADDRESS 51 #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc 52 #endif 53 54 #define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */ 55 #define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS 56 #define CONFIG_PCIE1 /* PCIE controller 1 */ 57 #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ 58 #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ 59 60 #ifndef CONFIG_ARCH_B4420 61 #define CONFIG_SYS_SRIO 62 #define CONFIG_SRIO1 /* SRIO port 1 */ 63 #define CONFIG_SRIO2 /* SRIO port 2 */ 64 #define CONFIG_SRIO_PCIE_BOOT_MASTER 65 #endif 66 67 /* I2C bus multiplexer */ 68 #define I2C_MUX_PCA_ADDR 0x77 69 70 /* VSC Crossbar switches */ 71 #define CONFIG_VSC_CROSSBAR 72 #define I2C_CH_DEFAULT 0x8 73 #define I2C_CH_VSC3316 0xc 74 #define I2C_CH_VSC3308 0xd 75 76 #define VSC3316_TX_ADDRESS 0x70 77 #define VSC3316_RX_ADDRESS 0x71 78 #define VSC3308_TX_ADDRESS 0x02 79 #define VSC3308_RX_ADDRESS 0x03 80 81 /* IDT clock synthesizers */ 82 #define CONFIG_IDT8T49N222A 83 #define I2C_CH_IDT 0x9 84 85 #define IDT_SERDES1_ADDRESS 0x6E 86 #define IDT_SERDES2_ADDRESS 0x6C 87 88 /* Voltage monitor on channel 2*/ 89 #define I2C_MUX_CH_VOL_MONITOR 0xa 90 #define I2C_VOL_MONITOR_ADDR 0x40 91 #define I2C_VOL_MONITOR_BUS_V_OFFSET 0x2 92 #define I2C_VOL_MONITOR_BUS_V_OVF 0x1 93 #define I2C_VOL_MONITOR_BUS_V_SHIFT 3 94 95 #define CONFIG_ZM7300 96 #define I2C_MUX_CH_DPM 0xa 97 #define I2C_DPM_ADDR 0x28 98 99 #define CONFIG_ENV_OVERWRITE 100 101 #if defined(CONFIG_SPIFLASH) 102 #define CONFIG_ENV_SPI_BUS 0 103 #define CONFIG_ENV_SPI_CS 0 104 #define CONFIG_ENV_SPI_MAX_HZ 10000000 105 #define CONFIG_ENV_SPI_MODE 0 106 #define CONFIG_ENV_SIZE 0x2000 /* 8KB */ 107 #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ 108 #define CONFIG_ENV_SECT_SIZE 0x10000 109 #elif defined(CONFIG_SDCARD) 110 #define CONFIG_SYS_MMC_ENV_DEV 0 111 #define CONFIG_ENV_SIZE 0x2000 112 #define CONFIG_ENV_OFFSET (512 * 1097) 113 #elif defined(CONFIG_NAND) 114 #define CONFIG_ENV_SIZE 0x2000 115 #define CONFIG_ENV_OFFSET (10 * CONFIG_SYS_NAND_BLOCK_SIZE) 116 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 117 #define CONFIG_ENV_ADDR 0xffe20000 118 #define CONFIG_ENV_SIZE 0x2000 119 #elif defined(CONFIG_ENV_IS_NOWHERE) 120 #define CONFIG_ENV_SIZE 0x2000 121 #else 122 #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) 123 #define CONFIG_ENV_SIZE 0x2000 124 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ 125 #endif 126 127 #ifndef __ASSEMBLY__ 128 unsigned long get_board_sys_clk(void); 129 unsigned long get_board_ddr_clk(void); 130 #endif 131 #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() /* sysclk for MPC85xx */ 132 #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() 133 134 /* 135 * These can be toggled for performance analysis, otherwise use default. 136 */ 137 #define CONFIG_SYS_CACHE_STASHING 138 #define CONFIG_BTB /* toggle branch predition */ 139 #define CONFIG_DDR_ECC 140 #ifdef CONFIG_DDR_ECC 141 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER 142 #define CONFIG_MEM_INIT_VALUE 0xdeadbeef 143 #endif 144 145 #define CONFIG_ENABLE_36BIT_PHYS 146 147 #ifdef CONFIG_PHYS_64BIT 148 #define CONFIG_ADDR_MAP 149 #define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */ 150 #endif 151 152 #if 0 153 #define CONFIG_POST CONFIG_SYS_POST_MEMORY /* test POST memory test */ 154 #endif 155 #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ 156 #define CONFIG_SYS_MEMTEST_END 0x00400000 157 158 /* 159 * Config the L3 Cache as L3 SRAM 160 */ 161 #define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000 162 #define CONFIG_SYS_L3_SIZE 256 << 10 163 #define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024) 164 #ifdef CONFIG_NAND 165 #define CONFIG_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024) 166 #endif 167 #define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024) 168 #define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10) 169 #define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024) 170 171 #ifdef CONFIG_PHYS_64BIT 172 #define CONFIG_SYS_DCSRBAR 0xf0000000 173 #define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull 174 #endif 175 176 /* EEPROM */ 177 #define CONFIG_ID_EEPROM 178 #define CONFIG_SYS_I2C_EEPROM_NXID 179 #define CONFIG_SYS_EEPROM_BUS_NUM 0 180 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x57 181 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 182 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 183 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5 184 185 /* 186 * DDR Setup 187 */ 188 #define CONFIG_VERY_BIG_RAM 189 #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 190 #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE 191 192 #define CONFIG_DIMM_SLOTS_PER_CTLR 1 193 #define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR) 194 195 #define CONFIG_DDR_SPD 196 #define CONFIG_SYS_DDR_RAW_TIMING 197 198 #define CONFIG_SYS_SPD_BUS_NUM 0 199 #define SPD_EEPROM_ADDRESS1 0x51 200 #define SPD_EEPROM_ADDRESS2 0x53 201 202 #define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1 203 #define CONFIG_SYS_SDRAM_SIZE 2048 /* for fixed parameter use */ 204 205 /* 206 * IFC Definitions 207 */ 208 #define CONFIG_SYS_FLASH_BASE 0xe0000000 209 #ifdef CONFIG_PHYS_64BIT 210 #define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE) 211 #else 212 #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE 213 #endif 214 215 #define CONFIG_SYS_NOR0_CSPR_EXT (0xf) 216 #define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \ 217 + 0x8000000) | \ 218 CSPR_PORT_SIZE_16 | \ 219 CSPR_MSEL_NOR | \ 220 CSPR_V) 221 #define CONFIG_SYS_NOR1_CSPR_EXT (0xf) 222 #define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \ 223 CSPR_PORT_SIZE_16 | \ 224 CSPR_MSEL_NOR | \ 225 CSPR_V) 226 #define CONFIG_SYS_NOR_AMASK IFC_AMASK(128 * 1024 * 1024) 227 /* NOR Flash Timing Params */ 228 #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) 229 #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ 230 FTIM0_NOR_TEADC(0x04) | \ 231 FTIM0_NOR_TEAHC(0x20)) 232 #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ 233 FTIM1_NOR_TRAD_NOR(0x1A) |\ 234 FTIM1_NOR_TSEQRAD_NOR(0x13)) 235 #define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x01) | \ 236 FTIM2_NOR_TCH(0x0E) | \ 237 FTIM2_NOR_TWPH(0x0E) | \ 238 FTIM2_NOR_TWP(0x1c)) 239 #define CONFIG_SYS_NOR_FTIM3 0x0 240 241 #define CONFIG_SYS_FLASH_QUIET_TEST 242 #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ 243 244 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */ 245 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */ 246 #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ 247 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ 248 249 #define CONFIG_SYS_FLASH_EMPTY_INFO 250 #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \ 251 + 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS} 252 253 #define CONFIG_FSL_QIXIS /* use common QIXIS code */ 254 #define CONFIG_FSL_QIXIS_V2 255 #define QIXIS_BASE 0xffdf0000 256 #ifdef CONFIG_PHYS_64BIT 257 #define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE) 258 #else 259 #define QIXIS_BASE_PHYS QIXIS_BASE 260 #endif 261 #define QIXIS_LBMAP_SWITCH 0x01 262 #define QIXIS_LBMAP_MASK 0x0f 263 #define QIXIS_LBMAP_SHIFT 0 264 #define QIXIS_LBMAP_DFLTBANK 0x00 265 #define QIXIS_LBMAP_ALTBANK 0x02 266 #define QIXIS_RST_CTL_RESET 0x31 267 #define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20 268 #define QIXIS_RCFG_CTL_RECONFIG_START 0x21 269 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08 270 271 #define CONFIG_SYS_CSPR3_EXT (0xf) 272 #define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \ 273 | CSPR_PORT_SIZE_8 \ 274 | CSPR_MSEL_GPCM \ 275 | CSPR_V) 276 #define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024) 277 #define CONFIG_SYS_CSOR3 0x0 278 /* QIXIS Timing parameters for IFC CS3 */ 279 #define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \ 280 FTIM0_GPCM_TEADC(0x0e) | \ 281 FTIM0_GPCM_TEAHC(0x0e)) 282 #define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0x0e) | \ 283 FTIM1_GPCM_TRAD(0x1f)) 284 #define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \ 285 FTIM2_GPCM_TCH(0x8) | \ 286 FTIM2_GPCM_TWP(0x1f)) 287 #define CONFIG_SYS_CS3_FTIM3 0x0 288 289 /* NAND Flash on IFC */ 290 #define CONFIG_NAND_FSL_IFC 291 #define CONFIG_SYS_NAND_MAX_ECCPOS 256 292 #define CONFIG_SYS_NAND_MAX_OOBFREE 2 293 #define CONFIG_SYS_NAND_BASE 0xff800000 294 #ifdef CONFIG_PHYS_64BIT 295 #define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE) 296 #else 297 #define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE 298 #endif 299 300 #define CONFIG_SYS_NAND_CSPR_EXT (0xf) 301 #define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ 302 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \ 303 | CSPR_MSEL_NAND /* MSEL = NAND */ \ 304 | CSPR_V) 305 #define CONFIG_SYS_NAND_AMASK IFC_AMASK(64 * 1024) 306 307 #define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \ 308 | CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \ 309 | CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \ 310 | CSOR_NAND_RAL_3 /* RAL = 2Byes */ \ 311 | CSOR_NAND_PGS_2K /* Page Size = 2K */ \ 312 | CSOR_NAND_SPRZ_64/* Spare size = 64 */ \ 313 | CSOR_NAND_PB(64)) /*Pages Per Block = 64*/ 314 315 #define CONFIG_SYS_NAND_ONFI_DETECTION 316 317 /* ONFI NAND Flash mode0 Timing Params */ 318 #define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \ 319 FTIM0_NAND_TWP(0x18) | \ 320 FTIM0_NAND_TWCHT(0x07) | \ 321 FTIM0_NAND_TWH(0x0a)) 322 #define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \ 323 FTIM1_NAND_TWBE(0x39) | \ 324 FTIM1_NAND_TRR(0x0e) | \ 325 FTIM1_NAND_TRP(0x18)) 326 #define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \ 327 FTIM2_NAND_TREH(0x0a) | \ 328 FTIM2_NAND_TWHRE(0x1e)) 329 #define CONFIG_SYS_NAND_FTIM3 0x0 330 331 #define CONFIG_SYS_NAND_DDR_LAW 11 332 333 #define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } 334 #define CONFIG_SYS_MAX_NAND_DEVICE 1 335 336 #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) 337 338 #if defined(CONFIG_NAND) 339 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT 340 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR 341 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK 342 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR 343 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 344 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 345 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 346 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 347 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR0_CSPR_EXT 348 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR0_CSPR 349 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK 350 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR 351 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0 352 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1 353 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2 354 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3 355 #else 356 #define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT 357 #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR 358 #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK 359 #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR 360 #define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0 361 #define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1 362 #define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2 363 #define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3 364 #define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT 365 #define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR 366 #define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK 367 #define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR 368 #define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0 369 #define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1 370 #define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2 371 #define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3 372 #endif 373 #define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT 374 #define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR 375 #define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK 376 #define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR 377 #define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 378 #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 379 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 380 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 381 382 #ifdef CONFIG_SPL_BUILD 383 #define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE 384 #else 385 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ 386 #endif 387 388 #if defined(CONFIG_RAMBOOT_PBL) 389 #define CONFIG_SYS_RAMBOOT 390 #endif 391 392 #define CONFIG_HWCONFIG 393 394 /* define to use L1 as initial stack */ 395 #define CONFIG_L1_INIT_RAM 396 #define CONFIG_SYS_INIT_RAM_LOCK 397 #define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */ 398 #ifdef CONFIG_PHYS_64BIT 399 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf 400 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000 401 /* The assembler doesn't like typecast */ 402 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS \ 403 ((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \ 404 CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW) 405 #else 406 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */ 407 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 408 #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS 409 #endif 410 #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 411 412 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ 413 GENERATED_GBL_DATA_SIZE) 414 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET 415 416 #define CONFIG_SYS_MONITOR_LEN (768 * 1024) 417 #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) 418 419 /* Serial Port - controlled on board with jumper J8 420 * open - index 2 421 * shorted - index 1 422 */ 423 #define CONFIG_SYS_NS16550_SERIAL 424 #define CONFIG_SYS_NS16550_REG_SIZE 1 425 #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) 426 427 #define CONFIG_SYS_BAUDRATE_TABLE \ 428 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} 429 430 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500) 431 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600) 432 #define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500) 433 #define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600) 434 435 /* I2C */ 436 #define CONFIG_SYS_I2C 437 #define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */ 438 #define CONFIG_SYS_FSL_I2C_SPEED 400000 /* I2C speed in Hz */ 439 #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F 440 #define CONFIG_SYS_FSL_I2C2_SPEED 400000 /* I2C speed in Hz */ 441 #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F 442 #define CONFIG_SYS_FSL_I2C_OFFSET 0x118000 443 #define CONFIG_SYS_FSL_I2C2_OFFSET 0x119000 444 445 /* 446 * RTC configuration 447 */ 448 #define RTC 449 #define CONFIG_RTC_DS3231 1 450 #define CONFIG_SYS_I2C_RTC_ADDR 0x68 451 452 /* 453 * RapidIO 454 */ 455 #ifdef CONFIG_SYS_SRIO 456 #ifdef CONFIG_SRIO1 457 #define CONFIG_SYS_SRIO1_MEM_VIRT 0xa0000000 458 #ifdef CONFIG_PHYS_64BIT 459 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xc20000000ull 460 #else 461 #define CONFIG_SYS_SRIO1_MEM_PHYS 0xa0000000 462 #endif 463 #define CONFIG_SYS_SRIO1_MEM_SIZE 0x10000000 /* 256M */ 464 #endif 465 466 #ifdef CONFIG_SRIO2 467 #define CONFIG_SYS_SRIO2_MEM_VIRT 0xb0000000 468 #ifdef CONFIG_PHYS_64BIT 469 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xc30000000ull 470 #else 471 #define CONFIG_SYS_SRIO2_MEM_PHYS 0xb0000000 472 #endif 473 #define CONFIG_SYS_SRIO2_MEM_SIZE 0x10000000 /* 256M */ 474 #endif 475 #endif 476 477 /* 478 * for slave u-boot IMAGE instored in master memory space, 479 * PHYS must be aligned based on the SIZE 480 */ 481 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull 482 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull 483 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */ 484 #define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull 485 /* 486 * for slave UCODE and ENV instored in master memory space, 487 * PHYS must be aligned based on the SIZE 488 */ 489 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull 490 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull 491 #define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */ 492 493 /* slave core release by master*/ 494 #define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4 495 #define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */ 496 497 /* 498 * SRIO_PCIE_BOOT - SLAVE 499 */ 500 #ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE 501 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000 502 #define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \ 503 (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR) 504 #endif 505 506 /* 507 * eSPI - Enhanced SPI 508 */ 509 #define CONFIG_SF_DEFAULT_SPEED 10000000 510 #define CONFIG_SF_DEFAULT_MODE 0 511 512 /* 513 * MAPLE 514 */ 515 #ifdef CONFIG_PHYS_64BIT 516 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xFA0000000ull 517 #else 518 #define CONFIG_SYS_MAPLE_MEM_PHYS 0xA0000000 519 #endif 520 521 /* 522 * General PCI 523 * Memory space is mapped 1-1, but I/O space must start from 0. 524 */ 525 526 /* controller 1, direct to uli, tgtid 3, Base address 20000 */ 527 #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 528 #ifdef CONFIG_PHYS_64BIT 529 #define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000 530 #define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull 531 #else 532 #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 533 #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 534 #endif 535 #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ 536 #define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000 537 #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 538 #ifdef CONFIG_PHYS_64BIT 539 #define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull 540 #else 541 #define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000 542 #endif 543 #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ 544 545 /* Qman/Bman */ 546 #ifndef CONFIG_NOBQFMAN 547 #define CONFIG_SYS_BMAN_NUM_PORTALS 25 548 #define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000 549 #ifdef CONFIG_PHYS_64BIT 550 #define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull 551 #else 552 #define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE 553 #endif 554 #define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000 555 #define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000 556 #define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000 557 #define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE 558 #define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 559 #define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \ 560 CONFIG_SYS_BMAN_CENA_SIZE) 561 #define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1) 562 #define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08 563 #define CONFIG_SYS_QMAN_NUM_PORTALS 25 564 #define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000 565 #ifdef CONFIG_PHYS_64BIT 566 #define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull 567 #else 568 #define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE 569 #endif 570 #define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000 571 #define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000 572 #define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000 573 #define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE 574 #define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 575 #define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \ 576 CONFIG_SYS_QMAN_CENA_SIZE) 577 #define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1) 578 #define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08 579 580 #define CONFIG_SYS_DPAA_FMAN 581 582 #define CONFIG_SYS_DPAA_RMAN 583 584 /* Default address of microcode for the Linux Fman driver */ 585 #if defined(CONFIG_SPIFLASH) 586 /* 587 * env is stored at 0x100000, sector size is 0x10000, ucode is stored after 588 * env, so we got 0x110000. 589 */ 590 #define CONFIG_SYS_QE_FW_IN_SPIFLASH 591 #define CONFIG_SYS_FMAN_FW_ADDR 0x110000 592 #elif defined(CONFIG_SDCARD) 593 /* 594 * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is 595 * about 545KB (1089 blocks), Env is stored after the image, and the env size is 596 * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130. 597 */ 598 #define CONFIG_SYS_QE_FMAN_FW_IN_MMC 599 #define CONFIG_SYS_FMAN_FW_ADDR (512 * 1130) 600 #elif defined(CONFIG_NAND) 601 #define CONFIG_SYS_QE_FMAN_FW_IN_NAND 602 #define CONFIG_SYS_FMAN_FW_ADDR (13 * CONFIG_SYS_NAND_BLOCK_SIZE) 603 #elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) 604 /* 605 * Slave has no ucode locally, it can fetch this from remote. When implementing 606 * in two corenet boards, slave's ucode could be stored in master's memory 607 * space, the address can be mapped from slave TLB->slave LAW-> 608 * slave SRIO or PCIE outbound window->master inbound window-> 609 * master LAW->the ucode address in master's memory space. 610 */ 611 #define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE 612 #define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000 613 #else 614 #define CONFIG_SYS_QE_FMAN_FW_IN_NOR 615 #define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000 616 #endif 617 #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 618 #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) 619 #endif /* CONFIG_NOBQFMAN */ 620 621 #ifdef CONFIG_SYS_DPAA_FMAN 622 #define CONFIG_FMAN_ENET 623 #define CONFIG_PHYLIB_10G 624 #define CONFIG_PHY_VITESSE 625 #define CONFIG_PHY_TERANETICS 626 #define SGMII_CARD_PORT1_PHY_ADDR 0x1C 627 #define SGMII_CARD_PORT2_PHY_ADDR 0x10 628 #define SGMII_CARD_PORT3_PHY_ADDR 0x1E 629 #define SGMII_CARD_PORT4_PHY_ADDR 0x11 630 #endif 631 632 #ifdef CONFIG_PCI 633 #define CONFIG_PCI_INDIRECT_BRIDGE 634 635 #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ 636 #endif /* CONFIG_PCI */ 637 638 #ifdef CONFIG_FMAN_ENET 639 #define CONFIG_SYS_FM1_ONBOARD_PHY1_ADDR 0x10 640 #define CONFIG_SYS_FM1_ONBOARD_PHY2_ADDR 0x11 641 642 /*B4860 QDS AMC2PEX-2S default PHY_ADDR */ 643 #define CONFIG_SYS_FM1_10GEC1_PHY_ADDR 0x7 /*SLOT 1*/ 644 #define CONFIG_SYS_FM1_10GEC2_PHY_ADDR 0x6 /*SLOT 2*/ 645 646 #define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR 0x1c 647 #define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR 0x1d 648 #define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR 0x1e 649 #define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR 0x1f 650 651 #define CONFIG_ETHPRIME "FM1@DTSEC1" 652 #endif 653 654 #define CONFIG_SYS_FSL_B4860QDS_XFI_ERR 655 656 /* 657 * Environment 658 */ 659 #define CONFIG_LOADS_ECHO /* echo on for serial download */ 660 #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ 661 662 /* 663 * USB 664 */ 665 #define CONFIG_HAS_FSL_DR_USB 666 667 #ifdef CONFIG_HAS_FSL_DR_USB 668 #ifdef CONFIG_USB_EHCI_HCD 669 #define CONFIG_USB_EHCI_FSL 670 #define CONFIG_EHCI_HCD_INIT_AFTER_RESET 671 #endif 672 #endif 673 674 /* 675 * Miscellaneous configurable options 676 */ 677 #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ 678 679 /* 680 * For booting Linux, the board info and command line data 681 * have to be in the first 64 MB of memory, since this is 682 * the maximum mapped by the Linux kernel during initialization. 683 */ 684 #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/ 685 #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ 686 687 #ifdef CONFIG_CMD_KGDB 688 #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ 689 #endif 690 691 /* 692 * Environment Configuration 693 */ 694 #define CONFIG_ROOTPATH "/opt/nfsroot" 695 #define CONFIG_BOOTFILE "uImage" 696 #define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server*/ 697 698 /* default location for tftp and bootm */ 699 #define CONFIG_LOADADDR 1000000 700 701 #define __USB_PHY_TYPE ulpi 702 703 #ifdef CONFIG_ARCH_B4860 704 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null," \ 705 "bank_intlv=cs0_cs1;" \ 706 "en_cpc:cpc2;" 707 #else 708 #define HWCONFIG "hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;" 709 #endif 710 711 #define CONFIG_EXTRA_ENV_SETTINGS \ 712 HWCONFIG \ 713 "usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\ 714 "netdev=eth0\0" \ 715 "uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \ 716 "ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \ 717 "tftpflash=tftpboot $loadaddr $uboot && " \ 718 "protect off $ubootaddr +$filesize && " \ 719 "erase $ubootaddr +$filesize && " \ 720 "cp.b $loadaddr $ubootaddr $filesize && " \ 721 "protect on $ubootaddr +$filesize && " \ 722 "cmp.b $loadaddr $ubootaddr $filesize\0" \ 723 "consoledev=ttyS0\0" \ 724 "ramdiskaddr=2000000\0" \ 725 "ramdiskfile=b4860qds/ramdisk.uboot\0" \ 726 "fdtaddr=1e00000\0" \ 727 "fdtfile=b4860qds/b4860qds.dtb\0" \ 728 "bdev=sda3\0" 729 730 /* For emulation this causes u-boot to jump to the start of the proof point 731 app code automatically */ 732 #define CONFIG_PROOF_POINTS \ 733 "setenv bootargs root=/dev/$bdev rw " \ 734 "console=$consoledev,$baudrate $othbootargs;" \ 735 "cpu 1 release 0x29000000 - - -;" \ 736 "cpu 2 release 0x29000000 - - -;" \ 737 "cpu 3 release 0x29000000 - - -;" \ 738 "cpu 4 release 0x29000000 - - -;" \ 739 "cpu 5 release 0x29000000 - - -;" \ 740 "cpu 6 release 0x29000000 - - -;" \ 741 "cpu 7 release 0x29000000 - - -;" \ 742 "go 0x29000000" 743 744 #define CONFIG_HVBOOT \ 745 "setenv bootargs config-addr=0x60000000; " \ 746 "bootm 0x01000000 - 0x00f00000" 747 748 #define CONFIG_ALU \ 749 "setenv bootargs root=/dev/$bdev rw " \ 750 "console=$consoledev,$baudrate $othbootargs;" \ 751 "cpu 1 release 0x01000000 - - -;" \ 752 "cpu 2 release 0x01000000 - - -;" \ 753 "cpu 3 release 0x01000000 - - -;" \ 754 "cpu 4 release 0x01000000 - - -;" \ 755 "cpu 5 release 0x01000000 - - -;" \ 756 "cpu 6 release 0x01000000 - - -;" \ 757 "cpu 7 release 0x01000000 - - -;" \ 758 "go 0x01000000" 759 760 #define CONFIG_LINUX \ 761 "setenv bootargs root=/dev/ram rw " \ 762 "console=$consoledev,$baudrate $othbootargs;" \ 763 "setenv ramdiskaddr 0x02000000;" \ 764 "setenv fdtaddr 0x01e00000;" \ 765 "setenv loadaddr 0x1000000;" \ 766 "bootm $loadaddr $ramdiskaddr $fdtaddr" 767 768 #define CONFIG_HDBOOT \ 769 "setenv bootargs root=/dev/$bdev rw " \ 770 "console=$consoledev,$baudrate $othbootargs;" \ 771 "tftp $loadaddr $bootfile;" \ 772 "tftp $fdtaddr $fdtfile;" \ 773 "bootm $loadaddr - $fdtaddr" 774 775 #define CONFIG_NFSBOOTCOMMAND \ 776 "setenv bootargs root=/dev/nfs rw " \ 777 "nfsroot=$serverip:$rootpath " \ 778 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ 779 "console=$consoledev,$baudrate $othbootargs;" \ 780 "tftp $loadaddr $bootfile;" \ 781 "tftp $fdtaddr $fdtfile;" \ 782 "bootm $loadaddr - $fdtaddr" 783 784 #define CONFIG_RAMBOOTCOMMAND \ 785 "setenv bootargs root=/dev/ram rw " \ 786 "console=$consoledev,$baudrate $othbootargs;" \ 787 "tftp $ramdiskaddr $ramdiskfile;" \ 788 "tftp $loadaddr $bootfile;" \ 789 "tftp $fdtaddr $fdtfile;" \ 790 "bootm $loadaddr $ramdiskaddr $fdtaddr" 791 792 #define CONFIG_BOOTCOMMAND CONFIG_LINUX 793 794 #include <asm/fsl_secure_boot.h> 795 796 #endif /* __CONFIG_H */ 797