xref: /openbmc/linux/drivers/net/phy/icplus.c (revision 4e4f10f6498bc5038c0a110b5f21682fcb5578d7)

/*
 * Driver for ICPlus PHYs
 *
 * Copyright (c) 2007 Freescale Semiconductor, Inc.
 *
 * This program is free software; you can redistribute  it and/or modify it
 * under  the terms of  the GNU General  Public License as published by the
 * Free Software Foundation;  either version 2 of the  License, or (at your
 * option) any later version.
 *
 */
#include <linux/kernel.h>
#include <linux/string.h>
#include <linux/errno.h>
#include <linux/unistd.h>
#include <linux/slab.h>
#include <linux/interrupt.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/skbuff.h>
#include <linux/spinlock.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
#include <linux/phy.h>

#include <asm/io.h>
#include <asm/irq.h>
#include <asm/uaccess.h>

MODULE_DESCRIPTION("ICPlus IP175C PHY driver");
MODULE_AUTHOR("Michael Barkowski");
MODULE_LICENSE("GPL");

static int ip175c_config_init(struct phy_device *phydev)
{
	int err, i;
	static int full_reset_performed = 0;

	if (full_reset_performed == 0) {

		/* master reset */
		err = phydev->bus->write(phydev->bus, 30, 0, 0x175c);
		if (err < 0)
			return err;

		/* ensure no bus delays overlap reset period */
		err = phydev->bus->read(phydev->bus, 30, 0);

		/* data sheet specifies reset period is 2 msec */
		mdelay(2);

		/* enable IP175C mode */
		err = phydev->bus->write(phydev->bus, 29, 31, 0x175c);
		if (err < 0)
			return err;

		/* Set MII0 speed and duplex (in PHY mode) */
		err = phydev->bus->write(phydev->bus, 29, 22, 0x420);
		if (err < 0)
			return err;

		/* reset switch ports */
		for (i = 0; i < 5; i++) {
			err = phydev->bus->write(phydev->bus, i,
						 MII_BMCR, BMCR_RESET);
			if (err < 0)
				return err;
		}

		for (i = 0; i < 5; i++)
			err = phydev->bus->read(phydev->bus, i, MII_BMCR);

		mdelay(2);

		full_reset_performed = 1;
	}

	if (phydev->addr != 4) {
		phydev->state = PHY_RUNNING;
		phydev->speed = SPEED_100;
		phydev->duplex = DUPLEX_FULL;
		phydev->link = 1;
		netif_carrier_on(phydev->attached_dev);
	}

	return 0;
}

static int ip175c_read_status(struct phy_device *phydev)
{
	if (phydev->addr == 4) /* WAN port */
		genphy_read_status(phydev);
	else
		/* Don't need to read status for switch ports */
		phydev->irq = PHY_IGNORE_INTERRUPT;

	return 0;
}

static int ip175c_config_aneg(struct phy_device *phydev)
{
	if (phydev->addr == 4) /* WAN port */
		genphy_config_aneg(phydev);

	return 0;
}

static struct phy_driver ip175c_driver = {
	.phy_id		= 0x02430d80,
	.name		= "ICPlus IP175C",
	.phy_id_mask	= 0x0ffffff0,
	.features	= PHY_BASIC_FEATURES,
	.config_init	= &ip175c_config_init,
	.config_aneg	= &ip175c_config_aneg,
	.read_status	= &ip175c_read_status,
	.driver		= { .owner = THIS_MODULE,},
};

static int __init ip175c_init(void)
{
	return phy_driver_register(&ip175c_driver);
}

static void __exit ip175c_exit(void)
{
	phy_driver_unregister(&ip175c_driver);
}

module_init(ip175c_init);
module_exit(ip175c_exit);

static struct mdio_device_id icplus_tbl[] = {
	{ 0x02430d80, 0x0ffffff0 },
	{ }
};

MODULE_DEVICE_TABLE(mdio, icplus_tbl);