xref: /openbmc/linux/drivers/mtd/devices/docg3.h (revision 75bf465f0bc33e9b776a46d6a1b9b990f5fb7c37)

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
 * Handles the M-Systems DiskOnChip G3 chip
 *
 * Copyright (C) 2011 Robert Jarzmik
 */

#ifndef _MTD_DOCG3_H
#define _MTD_DOCG3_H

#include <linux/mtd/mtd.h>

/*
 * Flash memory areas :
 *   - 0x0000 .. 0x07ff : IPL
 *   - 0x0800 .. 0x0fff : Data area
 *   - 0x1000 .. 0x17ff : Registers
 *   - 0x1800 .. 0x1fff : Unknown
 */
#define DOC_IOSPACE_IPL			0x0000
#define DOC_IOSPACE_DATA		0x0800
#define DOC_IOSPACE_SIZE		0x2000

/*
 * DOC G3 layout and adressing scheme
 *   A page address for the block "b", plane "P" and page "p":
 *   address = [bbbb bPpp pppp]
 */

#define DOC_ADDR_PAGE_MASK		0x3f
#define DOC_ADDR_BLOCK_SHIFT		6
#define DOC_LAYOUT_NBPLANES		2
#define DOC_LAYOUT_PAGES_PER_BLOCK	64
#define DOC_LAYOUT_PAGE_SIZE		512
#define DOC_LAYOUT_OOB_SIZE		16
#define DOC_LAYOUT_WEAR_SIZE		8
#define DOC_LAYOUT_PAGE_OOB_SIZE				\
	(DOC_LAYOUT_PAGE_SIZE + DOC_LAYOUT_OOB_SIZE)
#define DOC_LAYOUT_WEAR_OFFSET		(DOC_LAYOUT_PAGE_OOB_SIZE * 2)
#define DOC_LAYOUT_BLOCK_SIZE					\
	(DOC_LAYOUT_PAGES_PER_BLOCK * DOC_LAYOUT_PAGE_SIZE)

/*
 * ECC related constants
 */
#define DOC_ECC_BCH_M			14
#define DOC_ECC_BCH_T			4
#define DOC_ECC_BCH_PRIMPOLY		0x4443
#define DOC_ECC_BCH_SIZE		7
#define DOC_ECC_BCH_COVERED_BYTES				\
	(DOC_LAYOUT_PAGE_SIZE + DOC_LAYOUT_OOB_PAGEINFO_SZ +	\
	 DOC_LAYOUT_OOB_HAMMING_SZ)
#define DOC_ECC_BCH_TOTAL_BYTES					\
	(DOC_ECC_BCH_COVERED_BYTES + DOC_LAYOUT_OOB_BCH_SZ)

/*
 * Blocks distribution
 */
#define DOC_LAYOUT_BLOCK_BBT		0
#define DOC_LAYOUT_BLOCK_OTP		0
#define DOC_LAYOUT_BLOCK_FIRST_DATA	6

#define DOC_LAYOUT_PAGE_BBT		4

/*
 * Extra page OOB (16 bytes wide) layout
 */
#define DOC_LAYOUT_OOB_PAGEINFO_OFS	0
#define DOC_LAYOUT_OOB_HAMMING_OFS	7
#define DOC_LAYOUT_OOB_BCH_OFS		8
#define DOC_LAYOUT_OOB_UNUSED_OFS	15
#define DOC_LAYOUT_OOB_PAGEINFO_SZ	7
#define DOC_LAYOUT_OOB_HAMMING_SZ	1
#define DOC_LAYOUT_OOB_BCH_SZ		7
#define DOC_LAYOUT_OOB_UNUSED_SZ	1


#define DOC_CHIPID_G3			0x200
#define DOC_ERASE_MARK			0xaa
#define DOC_MAX_NBFLOORS		4
/*
 * Flash registers
 */
#define DOC_CHIPID			0x1000
#define DOC_TEST			0x1004
#define DOC_BUSLOCK			0x1006
#define DOC_ENDIANCONTROL		0x1008
#define DOC_DEVICESELECT		0x100a
#define DOC_ASICMODE			0x100c
#define DOC_CONFIGURATION		0x100e
#define DOC_INTERRUPTCONTROL		0x1010
#define DOC_READADDRESS			0x101a
#define DOC_DATAEND			0x101e
#define DOC_INTERRUPTSTATUS		0x1020

#define DOC_FLASHSEQUENCE		0x1032
#define DOC_FLASHCOMMAND		0x1034
#define DOC_FLASHADDRESS		0x1036
#define DOC_FLASHCONTROL		0x1038
#define DOC_NOP				0x103e

#define DOC_ECCCONF0			0x1040
#define DOC_ECCCONF1			0x1042
#define DOC_ECCPRESET			0x1044
#define DOC_HAMMINGPARITY		0x1046
#define DOC_BCH_HW_ECC(idx)		(0x1048 + idx)

#define DOC_PROTECTION			0x1056
#define DOC_DPS0_KEY			0x105c
#define DOC_DPS1_KEY			0x105e
#define DOC_DPS0_ADDRLOW		0x1060
#define DOC_DPS0_ADDRHIGH		0x1062
#define DOC_DPS1_ADDRLOW		0x1064
#define DOC_DPS1_ADDRHIGH		0x1066
#define DOC_DPS0_STATUS			0x106c
#define DOC_DPS1_STATUS			0x106e

#define DOC_ASICMODECONFIRM		0x1072
#define DOC_CHIPID_INV			0x1074
#define DOC_POWERMODE			0x107c

/*
 * Flash sequences
 * A sequence is preset before one or more commands are input to the chip.
 */
#define DOC_SEQ_RESET			0x00
#define DOC_SEQ_PAGE_SIZE_532		0x03
#define DOC_SEQ_SET_FASTMODE		0x05
#define DOC_SEQ_SET_RELIABLEMODE	0x09
#define DOC_SEQ_READ			0x12
#define DOC_SEQ_SET_PLANE1		0x0e
#define DOC_SEQ_SET_PLANE2		0x10
#define DOC_SEQ_PAGE_SETUP		0x1d
#define DOC_SEQ_ERASE			0x27
#define DOC_SEQ_PLANES_STATUS		0x31

/*
 * Flash commands
 */
#define DOC_CMD_READ_PLANE1		0x00
#define DOC_CMD_SET_ADDR_READ		0x05
#define DOC_CMD_READ_ALL_PLANES		0x30
#define DOC_CMD_READ_PLANE2		0x50
#define DOC_CMD_READ_FLASH		0xe0
#define DOC_CMD_PAGE_SIZE_532		0x3c

#define DOC_CMD_PROG_BLOCK_ADDR		0x60
#define DOC_CMD_PROG_CYCLE1		0x80
#define DOC_CMD_PROG_CYCLE2		0x10
#define DOC_CMD_PROG_CYCLE3		0x11
#define DOC_CMD_ERASECYCLE2		0xd0
#define DOC_CMD_READ_STATUS		0x70
#define DOC_CMD_PLANES_STATUS		0x71

#define DOC_CMD_RELIABLE_MODE		0x22
#define DOC_CMD_FAST_MODE		0xa2

#define DOC_CMD_RESET			0xff

/*
 * Flash register : DOC_FLASHCONTROL
 */
#define DOC_CTRL_VIOLATION		0x20
#define DOC_CTRL_CE			0x10
#define DOC_CTRL_UNKNOWN_BITS		0x08
#define DOC_CTRL_PROTECTION_ERROR	0x04
#define DOC_CTRL_SEQUENCE_ERROR		0x02
#define DOC_CTRL_FLASHREADY		0x01

/*
 * Flash register : DOC_ASICMODE
 */
#define DOC_ASICMODE_RESET		0x00
#define DOC_ASICMODE_NORMAL		0x01
#define DOC_ASICMODE_POWERDOWN		0x02
#define DOC_ASICMODE_MDWREN		0x04
#define DOC_ASICMODE_BDETCT_RESET	0x08
#define DOC_ASICMODE_RSTIN_RESET	0x10
#define DOC_ASICMODE_RAM_WE		0x20

/*
 * Flash register : DOC_ECCCONF0
 */
#define DOC_ECCCONF0_WRITE_MODE		0x0000
#define DOC_ECCCONF0_READ_MODE		0x8000
#define DOC_ECCCONF0_AUTO_ECC_ENABLE	0x4000
#define DOC_ECCCONF0_HAMMING_ENABLE	0x1000
#define DOC_ECCCONF0_BCH_ENABLE		0x0800
#define DOC_ECCCONF0_DATA_BYTES_MASK	0x07ff

/*
 * Flash register : DOC_ECCCONF1
 */
#define DOC_ECCCONF1_BCH_SYNDROM_ERR	0x80
#define DOC_ECCCONF1_UNKOWN1		0x40
#define DOC_ECCCONF1_PAGE_IS_WRITTEN	0x20
#define DOC_ECCCONF1_UNKOWN3		0x10
#define DOC_ECCCONF1_HAMMING_BITS_MASK	0x0f

/*
 * Flash register : DOC_PROTECTION
 */
#define DOC_PROTECT_FOUNDRY_OTP_LOCK	0x01
#define DOC_PROTECT_CUSTOMER_OTP_LOCK	0x02
#define DOC_PROTECT_LOCK_INPUT		0x04
#define DOC_PROTECT_STICKY_LOCK		0x08
#define DOC_PROTECT_PROTECTION_ENABLED	0x10
#define DOC_PROTECT_IPL_DOWNLOAD_LOCK	0x20
#define DOC_PROTECT_PROTECTION_ERROR	0x80

/*
 * Flash register : DOC_DPS0_STATUS and DOC_DPS1_STATUS
 */
#define DOC_DPS_OTP_PROTECTED		0x01
#define DOC_DPS_READ_PROTECTED		0x02
#define DOC_DPS_WRITE_PROTECTED		0x04
#define DOC_DPS_HW_LOCK_ENABLED		0x08
#define DOC_DPS_KEY_OK			0x80

/*
 * Flash register : DOC_CONFIGURATION
 */
#define DOC_CONF_IF_CFG			0x80
#define DOC_CONF_MAX_ID_MASK		0x30
#define DOC_CONF_VCCQ_3V		0x01

/*
 * Flash register : DOC_READADDRESS
 */
#define DOC_READADDR_INC		0x8000
#define DOC_READADDR_ONE_BYTE		0x4000
#define DOC_READADDR_ADDR_MASK		0x1fff

/*
 * Flash register : DOC_POWERMODE
 */
#define DOC_POWERDOWN_READY		0x80

/*
 * Status of erase and write operation
 */
#define DOC_PLANES_STATUS_FAIL		0x01
#define DOC_PLANES_STATUS_PLANE0_KO	0x02
#define DOC_PLANES_STATUS_PLANE1_KO	0x04

/*
 * DPS key management
 *
 * Each floor of docg3 has 2 protection areas: DPS0 and DPS1. These areas span
 * across block boundaries, and define whether these blocks can be read or
 * written.
 * The definition is dynamically stored in page 0 of blocks (2,3) for DPS0, and
 * page 0 of blocks (4,5) for DPS1.
 */
#define DOC_LAYOUT_DPS_KEY_LENGTH	8

/**
 * struct docg3_cascade - Cascade of 1 to 4 docg3 chips
 * @floors: floors (ie. one physical docg3 chip is one floor)
 * @base: IO space to access all chips in the cascade
 * @bch: the BCH correcting control structure
 * @lock: lock to protect docg3 IO space from concurrent accesses
 */
struct docg3_cascade {
	struct mtd_info *floors[DOC_MAX_NBFLOORS];
	void __iomem *base;
	struct bch_control *bch;
	struct mutex lock;
};

/**
 * struct docg3 - DiskOnChip driver private data
 * @dev: the device currently under control
 * @cascade: the cascade this device belongs to
 * @device_id: number of the cascaded DoCG3 device (0, 1, 2 or 3)
 * @if_cfg: if true, reads are on 16bits, else reads are on 8bits

 * @reliable: if 0, docg3 in normal mode, if 1 docg3 in fast mode, if 2 in
 *            reliable mode
 *            Fast mode implies more errors than normal mode.
 *            Reliable mode implies that page 2*n and 2*n+1 are clones.
 * @bbt: bad block table cache
 * @oob_write_ofs: offset of the MTD where this OOB should belong (ie. in next
 *                 page_write)
 * @oob_autoecc: if 1, use only bytes 0-7, 15, and fill the others with HW ECC
 *               if 0, use all the 16 bytes.
 * @oob_write_buf: prepared OOB for next page_write
 */
struct docg3 {
	struct device *dev;
	struct docg3_cascade *cascade;
	unsigned int device_id:4;
	unsigned int if_cfg:1;
	unsigned int reliable:2;
	int max_block;
	u8 *bbt;
	loff_t oob_write_ofs;
	int oob_autoecc;
	u8 oob_write_buf[DOC_LAYOUT_OOB_SIZE];
};

#define doc_err(fmt, arg...) dev_err(docg3->dev, (fmt), ## arg)
#define doc_info(fmt, arg...) dev_info(docg3->dev, (fmt), ## arg)
#define doc_dbg(fmt, arg...) dev_dbg(docg3->dev, (fmt), ## arg)
#define doc_vdbg(fmt, arg...) dev_vdbg(docg3->dev, (fmt), ## arg)
#endif

/*
 * Trace events part
 */
#undef TRACE_SYSTEM
#define TRACE_SYSTEM docg3

#if !defined(_MTD_DOCG3_TRACE) || defined(TRACE_HEADER_MULTI_READ)
#define _MTD_DOCG3_TRACE

#include <linux/tracepoint.h>

TRACE_EVENT(docg3_io,
	    TP_PROTO(int op, int width, u16 reg, int val),
	    TP_ARGS(op, width, reg, val),
	    TP_STRUCT__entry(
		    __field(int, op)
		    __field(unsigned char, width)
		    __field(u16, reg)
		    __field(int, val)),
	    TP_fast_assign(
		    __entry->op = op;
		    __entry->width = width;
		    __entry->reg = reg;
		    __entry->val = val;),
	    TP_printk("docg3: %s%02d reg=%04x, val=%04x",
		      __entry->op ? "write" : "read", __entry->width,
		      __entry->reg, __entry->val)
	);
#endif

/* This part must be outside protection */
#undef TRACE_INCLUDE_PATH
#undef TRACE_INCLUDE_FILE
#define TRACE_INCLUDE_PATH .
#define TRACE_INCLUDE_FILE docg3
#include <trace/define_trace.h>