1# SPDX-License-Identifier: GPL-2.0-only 2# 3# For a description of the syntax of this configuration file, 4# see Documentation/kbuild/kconfig-language.rst. 5# 6 7menu "Firmware Drivers" 8 9source "drivers/firmware/arm_scmi/Kconfig" 10 11config ARM_SCPI_PROTOCOL 12 tristate "ARM System Control and Power Interface (SCPI) Message Protocol" 13 depends on ARM || ARM64 || COMPILE_TEST 14 depends on MAILBOX 15 help 16 System Control and Power Interface (SCPI) Message Protocol is 17 defined for the purpose of communication between the Application 18 Cores(AP) and the System Control Processor(SCP). The MHU peripheral 19 provides a mechanism for inter-processor communication between SCP 20 and AP. 21 22 SCP controls most of the power management on the Application 23 Processors. It offers control and management of: the core/cluster 24 power states, various power domain DVFS including the core/cluster, 25 certain system clocks configuration, thermal sensors and many 26 others. 27 28 This protocol library provides interface for all the client drivers 29 making use of the features offered by the SCP. 30 31config ARM_SCPI_POWER_DOMAIN 32 tristate "SCPI power domain driver" 33 depends on ARM_SCPI_PROTOCOL || (COMPILE_TEST && OF) 34 default y 35 select PM_GENERIC_DOMAINS if PM 36 help 37 This enables support for the SCPI power domains which can be 38 enabled or disabled via the SCP firmware 39 40config ARM_SDE_INTERFACE 41 bool "ARM Software Delegated Exception Interface (SDEI)" 42 depends on ARM64 43 help 44 The Software Delegated Exception Interface (SDEI) is an ARM 45 standard for registering callbacks from the platform firmware 46 into the OS. This is typically used to implement RAS notifications. 47 48config EDD 49 tristate "BIOS Enhanced Disk Drive calls determine boot disk" 50 depends on X86 51 help 52 Say Y or M here if you want to enable BIOS Enhanced Disk Drive 53 Services real mode BIOS calls to determine which disk 54 BIOS tries boot from. This information is then exported via sysfs. 55 56 This option is experimental and is known to fail to boot on some 57 obscure configurations. Most disk controller BIOS vendors do 58 not yet implement this feature. 59 60config EDD_OFF 61 bool "Sets default behavior for EDD detection to off" 62 depends on EDD 63 default n 64 help 65 Say Y if you want EDD disabled by default, even though it is compiled into the 66 kernel. Say N if you want EDD enabled by default. EDD can be dynamically set 67 using the kernel parameter 'edd={on|skipmbr|off}'. 68 69config FIRMWARE_MEMMAP 70 bool "Add firmware-provided memory map to sysfs" if EXPERT 71 default X86 72 help 73 Add the firmware-provided (unmodified) memory map to /sys/firmware/memmap. 74 That memory map is used for example by kexec to set up parameter area 75 for the next kernel, but can also be used for debugging purposes. 76 77 See also Documentation/ABI/testing/sysfs-firmware-memmap. 78 79config EFI_PCDP 80 bool "Console device selection via EFI PCDP or HCDP table" 81 depends on ACPI && EFI && IA64 82 default y if IA64 83 help 84 If your firmware supplies the PCDP table, and you want to 85 automatically use the primary console device it describes 86 as the Linux console, say Y here. 87 88 If your firmware supplies the HCDP table, and you want to 89 use the first serial port it describes as the Linux console, 90 say Y here. If your EFI ConOut path contains only a UART 91 device, it will become the console automatically. Otherwise, 92 you must specify the "console=hcdp" kernel boot argument. 93 94 Neither the PCDP nor the HCDP affects naming of serial devices, 95 so a serial console may be /dev/ttyS0, /dev/ttyS1, etc, depending 96 on how the driver discovers devices. 97 98 You must also enable the appropriate drivers (serial, VGA, etc.) 99 100 See DIG64_HCDPv20_042804.pdf available from 101 <http://www.dig64.org/specifications/> 102 103config DMIID 104 bool "Export DMI identification via sysfs to userspace" 105 depends on DMI 106 default y 107 help 108 Say Y here if you want to query SMBIOS/DMI system identification 109 information from userspace through /sys/class/dmi/id/ or if you want 110 DMI-based module auto-loading. 111 112config DMI_SYSFS 113 tristate "DMI table support in sysfs" 114 depends on SYSFS && DMI 115 default n 116 help 117 Say Y or M here to enable the exporting of the raw DMI table 118 data via sysfs. This is useful for consuming the data without 119 requiring any access to /dev/mem at all. Tables are found 120 under /sys/firmware/dmi when this option is enabled and 121 loaded. 122 123config DMI_SCAN_MACHINE_NON_EFI_FALLBACK 124 bool 125 126config ISCSI_IBFT_FIND 127 bool "iSCSI Boot Firmware Table Attributes" 128 depends on X86 && ISCSI_IBFT 129 default n 130 help 131 This option enables the kernel to find the region of memory 132 in which the ISCSI Boot Firmware Table (iBFT) resides. This 133 is necessary for iSCSI Boot Firmware Table Attributes module to work 134 properly. 135 136config ISCSI_IBFT 137 tristate "iSCSI Boot Firmware Table Attributes module" 138 select ISCSI_BOOT_SYSFS 139 select ISCSI_IBFT_FIND if X86 140 depends on ACPI && SCSI && SCSI_LOWLEVEL 141 default n 142 help 143 This option enables support for detection and exposing of iSCSI 144 Boot Firmware Table (iBFT) via sysfs to userspace. If you wish to 145 detect iSCSI boot parameters dynamically during system boot, say Y. 146 Otherwise, say N. 147 148config RASPBERRYPI_FIRMWARE 149 tristate "Raspberry Pi Firmware Driver" 150 depends on BCM2835_MBOX 151 help 152 This option enables support for communicating with the firmware on the 153 Raspberry Pi. 154 155config FW_CFG_SYSFS 156 tristate "QEMU fw_cfg device support in sysfs" 157 depends on SYSFS && (ARM || ARM64 || PARISC || PPC_PMAC || SPARC || X86) 158 depends on HAS_IOPORT_MAP 159 default n 160 help 161 Say Y or M here to enable the exporting of the QEMU firmware 162 configuration (fw_cfg) file entries via sysfs. Entries are 163 found under /sys/firmware/fw_cfg when this option is enabled 164 and loaded. 165 166config FW_CFG_SYSFS_CMDLINE 167 bool "QEMU fw_cfg device parameter parsing" 168 depends on FW_CFG_SYSFS 169 help 170 Allow the qemu_fw_cfg device to be initialized via the kernel 171 command line or using a module parameter. 172 WARNING: Using incorrect parameters (base address in particular) 173 may crash your system. 174 175config INTEL_STRATIX10_SERVICE 176 tristate "Intel Stratix10 Service Layer" 177 depends on ARCH_INTEL_SOCFPGA && ARM64 && HAVE_ARM_SMCCC 178 default n 179 help 180 Intel Stratix10 service layer runs at privileged exception level, 181 interfaces with the service providers (FPGA manager is one of them) 182 and manages secure monitor call to communicate with secure monitor 183 software at secure monitor exception level. 184 185 Say Y here if you want Stratix10 service layer support. 186 187config INTEL_STRATIX10_RSU 188 tristate "Intel Stratix10 Remote System Update" 189 depends on INTEL_STRATIX10_SERVICE 190 help 191 The Intel Remote System Update (RSU) driver exposes interfaces 192 access through the Intel Service Layer to user space via sysfs 193 device attribute nodes. The RSU interfaces report/control some of 194 the optional RSU features of the Stratix 10 SoC FPGA. 195 196 The RSU provides a way for customers to update the boot 197 configuration of a Stratix 10 SoC device with significantly reduced 198 risk of corrupting the bitstream storage and bricking the system. 199 200 Enable RSU support if you are using an Intel SoC FPGA with the RSU 201 feature enabled and you want Linux user space control. 202 203 Say Y here if you want Intel RSU support. 204 205config QCOM_SCM 206 bool 207 depends on ARM || ARM64 208 depends on HAVE_ARM_SMCCC 209 select RESET_CONTROLLER 210 211config QCOM_SCM_DOWNLOAD_MODE_DEFAULT 212 bool "Qualcomm download mode enabled by default" 213 depends on QCOM_SCM 214 help 215 A device with "download mode" enabled will upon an unexpected 216 warm-restart enter a special debug mode that allows the user to 217 "download" memory content over USB for offline postmortem analysis. 218 The feature can be enabled/disabled on the kernel command line. 219 220 Say Y here to enable "download mode" by default. 221 222config TI_SCI_PROTOCOL 223 tristate "TI System Control Interface (TISCI) Message Protocol" 224 depends on TI_MESSAGE_MANAGER 225 help 226 TI System Control Interface (TISCI) Message Protocol is used to manage 227 compute systems such as ARM, DSP etc with the system controller in 228 complex System on Chip(SoC) such as those found on certain keystone 229 generation SoC from TI. 230 231 System controller provides various facilities including power 232 management function support. 233 234 This protocol library is used by client drivers to use the features 235 provided by the system controller. 236 237config TRUSTED_FOUNDATIONS 238 bool "Trusted Foundations secure monitor support" 239 depends on ARM && CPU_V7 240 help 241 Some devices (including most early Tegra-based consumer devices on 242 the market) are booted with the Trusted Foundations secure monitor 243 active, requiring some core operations to be performed by the secure 244 monitor instead of the kernel. 245 246 This option allows the kernel to invoke the secure monitor whenever 247 required on devices using Trusted Foundations. See the functions and 248 comments in linux/firmware/trusted_foundations.h or the device tree 249 bindings for "tlm,trusted-foundations" for details on how to use it. 250 251 Choose N if you don't know what this is about. 252 253config TURRIS_MOX_RWTM 254 tristate "Turris Mox rWTM secure firmware driver" 255 depends on ARCH_MVEBU || COMPILE_TEST 256 depends on HAS_DMA && OF 257 depends on MAILBOX 258 select HW_RANDOM 259 select ARMADA_37XX_RWTM_MBOX 260 help 261 This driver communicates with the firmware on the Cortex-M3 secure 262 processor of the Turris Mox router. Enable if you are building for 263 Turris Mox, and you will be able to read the device serial number and 264 other manufacturing data and also utilize the Entropy Bit Generator 265 for hardware random number generation. 266 267source "drivers/firmware/arm_ffa/Kconfig" 268source "drivers/firmware/broadcom/Kconfig" 269source "drivers/firmware/google/Kconfig" 270source "drivers/firmware/efi/Kconfig" 271source "drivers/firmware/imx/Kconfig" 272source "drivers/firmware/meson/Kconfig" 273source "drivers/firmware/psci/Kconfig" 274source "drivers/firmware/smccc/Kconfig" 275source "drivers/firmware/tegra/Kconfig" 276source "drivers/firmware/xilinx/Kconfig" 277 278endmenu 279