xref: /openbmc/linux/arch/arm64/boot/dts/qcom/sc8180x.dtsi (revision 442d55d099ed72d96aee996e56f802b5cf885f39)

// SPDX-License-Identifier: BSD-3-Clause
/*
 * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
 * Copyright (c) 2020-2023, Linaro Limited
 */

#include <dt-bindings/clock/qcom,dispcc-sm8250.h>
#include <dt-bindings/clock/qcom,gcc-sc8180x.h>
#include <dt-bindings/clock/qcom,gpucc-sm8150.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interconnect/qcom,osm-l3.h>
#include <dt-bindings/interconnect/qcom,sc8180x.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
#include <dt-bindings/thermal/thermal.h>

/ {
	interrupt-parent = <&intc>;

	#address-cells = <2>;
	#size-cells = <2>;

	clocks {
		xo_board_clk: xo-board {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <38400000>;
		};

		sleep_clk: sleep-clk {
			compatible = "fixed-clock";
			#clock-cells = <0>;
			clock-frequency = <32764>;
			clock-output-names = "sleep_clk";
		};
	};

	cpus {
		#address-cells = <2>;
		#size-cells = <0>;

		CPU0: cpu@0 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x0>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_0>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD0>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 0>;

			L2_0: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
				L3_0: l3-cache {
					compatible = "cache";
					cache-level = <3>;
				};
			};
		};

		CPU1: cpu@100 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x100>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_100>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD1>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 0>;

			L2_100: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};

		};

		CPU2: cpu@200 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x200>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_200>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD2>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 0>;

			L2_200: l2-cache {
				compatible = "cache";
				cache-level = <2>;
				cache-unified;
				next-level-cache = <&L3_0>;
			};
		};

		CPU3: cpu@300 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x300>;
			enable-method = "psci";
			capacity-dmips-mhz = <602>;
			next-level-cache = <&L2_300>;
			qcom,freq-domain = <&cpufreq_hw 0>;
			operating-points-v2 = <&cpu0_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD3>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 0>;

			L2_300: l2-cache {
				compatible = "cache";
				cache-unified;
				cache-level = <2>;
				next-level-cache = <&L3_0>;
			};
		};

		CPU4: cpu@400 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x400>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_400>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD4>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 1>;

			L2_400: l2-cache {
				compatible = "cache";
				cache-unified;
				cache-level = <2>;
				next-level-cache = <&L3_0>;
			};
		};

		CPU5: cpu@500 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x500>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_500>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD5>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 1>;

			L2_500: l2-cache {
				compatible = "cache";
				cache-unified;
				cache-level = <2>;
				next-level-cache = <&L3_0>;
			};
		};

		CPU6: cpu@600 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x600>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_600>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD6>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 1>;

			L2_600: l2-cache {
				compatible = "cache";
				cache-unified;
				cache-level = <2>;
				next-level-cache = <&L3_0>;
			};
		};

		CPU7: cpu@700 {
			device_type = "cpu";
			compatible = "qcom,kryo485";
			reg = <0x0 0x700>;
			enable-method = "psci";
			capacity-dmips-mhz = <1024>;
			next-level-cache = <&L2_700>;
			qcom,freq-domain = <&cpufreq_hw 1>;
			operating-points-v2 = <&cpu4_opp_table>;
			interconnects = <&gem_noc MASTER_AMPSS_M0 3 &mc_virt SLAVE_EBI_CH0 3>,
					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
			power-domains = <&CPU_PD7>;
			power-domain-names = "psci";
			#cooling-cells = <2>;
			clocks = <&cpufreq_hw 1>;

			L2_700: l2-cache {
				compatible = "cache";
				cache-unified;
				cache-level = <2>;
				next-level-cache = <&L3_0>;
			};
		};

		cpu-map {
			cluster0 {
				core0 {
					cpu = <&CPU0>;
				};

				core1 {
					cpu = <&CPU1>;
				};

				core2 {
					cpu = <&CPU2>;
				};

				core3 {
					cpu = <&CPU3>;
				};

				core4 {
					cpu = <&CPU4>;
				};

				core5 {
					cpu = <&CPU5>;
				};

				core6 {
					cpu = <&CPU6>;
				};

				core7 {
					cpu = <&CPU7>;
				};
			};
		};

		idle-states {
			entry-method = "psci";

			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
				compatible = "arm,idle-state";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <355>;
				exit-latency-us = <909>;
				min-residency-us = <3934>;
				local-timer-stop;
			};

			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
				compatible = "arm,idle-state";
				arm,psci-suspend-param = <0x40000004>;
				entry-latency-us = <241>;
				exit-latency-us = <1461>;
				min-residency-us = <4488>;
				local-timer-stop;
			};
		};

		domain-idle-states {
			CLUSTER_SLEEP_0: cluster-sleep-0 {
				compatible = "domain-idle-state";
				arm,psci-suspend-param = <0x4100c244>;
				entry-latency-us = <3263>;
				exit-latency-us = <6562>;
				min-residency-us = <9987>;
			};
		};
	};

	cpu0_opp_table: opp-table-cpu0 {
		compatible = "operating-points-v2";
		opp-shared;

		opp-300000000 {
			opp-hz = /bits/ 64 <300000000>;
			opp-peak-kBps = <800000 9600000>;
		};

		opp-422400000 {
			opp-hz = /bits/ 64 <422400000>;
			opp-peak-kBps = <800000 9600000>;
		};

		opp-537600000 {
			opp-hz = /bits/ 64 <537600000>;
			opp-peak-kBps = <800000 12902400>;
		};

		opp-652800000 {
			opp-hz = /bits/ 64 <652800000>;
			opp-peak-kBps = <800000 12902400>;
		};

		opp-768000000 {
			opp-hz = /bits/ 64 <768000000>;
			opp-peak-kBps = <800000 15974400>;
		};

		opp-883200000 {
			opp-hz = /bits/ 64 <883200000>;
			opp-peak-kBps = <1804000 19660800>;
		};

		opp-998400000 {
			opp-hz = /bits/ 64 <998400000>;
			opp-peak-kBps = <1804000 19660800>;
		};

		opp-1113600000 {
			opp-hz = /bits/ 64 <1113600000>;
			opp-peak-kBps = <1804000 22732800>;
		};

		opp-1228800000 {
			opp-hz = /bits/ 64 <1228800000>;
			opp-peak-kBps = <1804000 22732800>;
		};

		opp-1363200000 {
			opp-hz = /bits/ 64 <1363200000>;
			opp-peak-kBps = <2188000 25804800>;
		};

		opp-1478400000 {
			opp-hz = /bits/ 64 <1478400000>;
			opp-peak-kBps = <2188000 31948800>;
		};

		opp-1574400000 {
			opp-hz = /bits/ 64 <1574400000>;
			opp-peak-kBps = <3072000 31948800>;
		};

		opp-1670400000 {
			opp-hz = /bits/ 64 <1670400000>;
			opp-peak-kBps = <3072000 31948800>;
		};

		opp-1766400000 {
			opp-hz = /bits/ 64 <1766400000>;
			opp-peak-kBps = <3072000 31948800>;
		};
	};

	cpu4_opp_table: opp-table-cpu4 {
		compatible = "operating-points-v2";
		opp-shared;

		opp-825600000 {
			opp-hz = /bits/ 64 <825600000>;
			opp-peak-kBps = <1804000 15974400>;
		};

		opp-940800000 {
			opp-hz = /bits/ 64 <940800000>;
			opp-peak-kBps = <2188000 19660800>;
		};

		opp-1056000000 {
			opp-hz = /bits/ 64 <1056000000>;
			opp-peak-kBps = <2188000 22732800>;
		};

		opp-1171200000 {
			opp-hz = /bits/ 64 <1171200000>;
			opp-peak-kBps = <3072000 25804800>;
		};

		opp-1286400000 {
			opp-hz = /bits/ 64 <1286400000>;
			opp-peak-kBps = <3072000 31948800>;
		};

		opp-1420800000 {
			opp-hz = /bits/ 64 <1420800000>;
			opp-peak-kBps = <4068000 31948800>;
		};

		opp-1536000000 {
			opp-hz = /bits/ 64 <1536000000>;
			opp-peak-kBps = <4068000 31948800>;
		};

		opp-1651200000 {
			opp-hz = /bits/ 64 <1651200000>;
			opp-peak-kBps = <4068000 40550400>;
		};

		opp-1766400000 {
			opp-hz = /bits/ 64 <1766400000>;
			opp-peak-kBps = <4068000 40550400>;
		};

		opp-1881600000 {
			opp-hz = /bits/ 64 <1881600000>;
			opp-peak-kBps = <4068000 43008000>;
		};

		opp-1996800000 {
			opp-hz = /bits/ 64 <1996800000>;
			opp-peak-kBps = <6220000 43008000>;
		};

		opp-2131200000 {
			opp-hz = /bits/ 64 <2131200000>;
			opp-peak-kBps = <6220000 49152000>;
		};

		opp-2246400000 {
			opp-hz = /bits/ 64 <2246400000>;
			opp-peak-kBps = <7216000 49152000>;
		};

		opp-2361600000 {
			opp-hz = /bits/ 64 <2361600000>;
			opp-peak-kBps = <8368000 49152000>;
		};

		opp-2457600000 {
			opp-hz = /bits/ 64 <2457600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2553600000 {
			opp-hz = /bits/ 64 <2553600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2649600000 {
			opp-hz = /bits/ 64 <2649600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2745600000 {
			opp-hz = /bits/ 64 <2745600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2841600000 {
			opp-hz = /bits/ 64 <2841600000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2918400000 {
			opp-hz = /bits/ 64 <2918400000>;
			opp-peak-kBps = <8368000 51609600>;
		};

		opp-2995200000 {
			opp-hz = /bits/ 64 <2995200000>;
			opp-peak-kBps = <8368000 51609600>;
		};
	};

	firmware {
		scm: scm {
			compatible = "qcom,scm-sc8180x", "qcom,scm";
		};
	};

	camnoc_virt: interconnect-camnoc-virt {
		compatible = "qcom,sc8180x-camnoc-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	mc_virt: interconnect-mc-virt {
		compatible = "qcom,sc8180x-mc-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	qup_virt: interconnect-qup-virt {
		compatible = "qcom,sc8180x-qup-virt";
		#interconnect-cells = <2>;
		qcom,bcm-voters = <&apps_bcm_voter>;
	};

	memory@80000000 {
		device_type = "memory";
		/* We expect the bootloader to fill in the size */
		reg = <0x0 0x80000000 0x0 0x0>;
	};

	pmu {
		compatible = "arm,armv8-pmuv3";
		interrupts = <GIC_PPI 5 IRQ_TYPE_LEVEL_HIGH>;
	};

	psci {
		compatible = "arm,psci-1.0";
		method = "smc";

		CPU_PD0: power-domain-cpu0 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD1: power-domain-cpu1 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD2: power-domain-cpu2 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD3: power-domain-cpu3 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
		};

		CPU_PD4: power-domain-cpu4 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD5: power-domain-cpu5 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD6: power-domain-cpu6 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CPU_PD7: power-domain-cpu7 {
			#power-domain-cells = <0>;
			power-domains = <&CLUSTER_PD>;
			domain-idle-states = <&BIG_CPU_SLEEP_0>;
		};

		CLUSTER_PD: power-domain-cpu-cluster0 {
			#power-domain-cells = <0>;
			domain-idle-states = <&CLUSTER_SLEEP_0>;
		};
	};

	reserved-memory {
		#address-cells = <2>;
		#size-cells = <2>;
		ranges;

		hyp_mem: hyp@85700000 {
			reg = <0x0 0x85700000 0x0 0x600000>;
			no-map;
		};

		xbl_mem: xbl@85d00000 {
			reg = <0x0 0x85d00000 0x0 0x140000>;
			no-map;
		};

		aop_mem: aop@85f00000 {
			reg = <0x0 0x85f00000 0x0 0x20000>;
			no-map;
		};

		aop_cmd_db: cmd-db@85f20000 {
			compatible = "qcom,cmd-db";
			reg = <0x0 0x85f20000 0x0 0x20000>;
			no-map;
		};

		reserved@85f40000 {
			reg = <0x0 0x85f40000 0x0 0x10000>;
			no-map;
		};

		smem_mem: smem@86000000 {
			compatible = "qcom,smem";
			reg = <0x0 0x86000000 0x0 0x200000>;
			no-map;
			hwlocks = <&tcsr_mutex 3>;
		};

		reserved@86200000 {
			reg = <0x0 0x86200000 0x0 0x3900000>;
			no-map;
		};

		reserved@89b00000 {
			reg = <0x0 0x89b00000 0x0 0x1c00000>;
			no-map;
		};

		reserved@9d400000 {
			reg = <0x0 0x9d400000 0x0 0x1000000>;
			no-map;
		};

		reserved@9e400000 {
			reg = <0x0 0x9e400000 0x0 0x1400000>;
			no-map;
		};

		reserved@9f800000 {
			reg = <0x0 0x9f800000 0x0 0x800000>;
			no-map;
		};
	};

	smp2p-cdsp {
		compatible = "qcom,smp2p";
		qcom,smem = <94>, <432>;

		interrupts = <GIC_SPI 576 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 6>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <5>;

		cdsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		cdsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-lpass {
		compatible = "qcom,smp2p";
		qcom,smem = <443>, <429>;

		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 10>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <2>;

		adsp_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		adsp_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-mpss {
		compatible = "qcom,smp2p";
		qcom,smem = <435>, <428>;

		interrupts = <GIC_SPI 451 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 14>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <1>;

		modem_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		modem_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};

		modem_smp2p_ipa_out: ipa-ap-to-modem {
			qcom,entry-name = "ipa";
			#qcom,smem-state-cells = <1>;
		};

		modem_smp2p_ipa_in: ipa-modem-to-ap {
			qcom,entry-name = "ipa";
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		modem_smp2p_wlan_in: wlan-wpss-to-ap {
			qcom,entry-name = "wlan";
			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	smp2p-slpi {
		compatible = "qcom,smp2p";
		qcom,smem = <481>, <430>;

		interrupts = <GIC_SPI 172 IRQ_TYPE_EDGE_RISING>;

		mboxes = <&apss_shared 26>;

		qcom,local-pid = <0>;
		qcom,remote-pid = <3>;

		slpi_smp2p_out: master-kernel {
			qcom,entry-name = "master-kernel";
			#qcom,smem-state-cells = <1>;
		};

		slpi_smp2p_in: slave-kernel {
			qcom,entry-name = "slave-kernel";

			interrupt-controller;
			#interrupt-cells = <2>;
		};
	};

	soc: soc@0 {
		compatible = "simple-bus";
		#address-cells = <2>;
		#size-cells = <2>;
		ranges = <0 0 0 0 0x10 0>;
		dma-ranges = <0 0 0 0 0x10 0>;

		gcc: clock-controller@100000 {
			compatible = "qcom,gcc-sc8180x";
			reg = <0x0 0x00100000 0x0 0x1f0000>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&rpmhcc RPMH_CXO_CLK_A>,
				 <&sleep_clk>;
			clock-names = "bi_tcxo",
				      "bi_tcxo_ao",
				      "sleep_clk";
		};

		qupv3_id_0: geniqup@8c0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0 0x008c0000 0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			iommus = <&apps_smmu 0x4c3 0>;
			status = "disabled";

			i2c0: i2c@880000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00880000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi0: spi@880000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00880000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart0: serial@880000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00880000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c1: i2c@884000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00884000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi1: spi@884000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00884000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart1: serial@884000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00884000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c2: i2c@888000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00888000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi2: spi@888000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00888000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart2: serial@888000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00888000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c3: i2c@88c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0088c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi3: spi@88c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0088c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart3: serial@88c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x0088c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c4: i2c@890000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00890000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi4: spi@890000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00890000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart4: serial@890000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00890000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c5: i2c@894000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00894000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi5: spi@894000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00894000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart5: serial@894000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00894000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c6: i2c@898000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00898000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi6: spi@898000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00898000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart6: serial@898000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00898000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c7: i2c@89c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x0089c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi7: spi@89c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x0089c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart7: serial@89c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x0089c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		qupv3_id_1: geniqup@ac0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x00ac0000 0x0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			iommus = <&apps_smmu 0x603 0>;
			status = "disabled";

			i2c8: i2c@a80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi8: spi@a80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart8: serial@a80000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c9: i2c@a84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi9: spi@a84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart9: serial@a84000 {
				compatible = "qcom,geni-debug-uart";
				reg = <0 0x00a84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c10: i2c@a88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi10: spi@a88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart10: serial@a88000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c11: i2c@a8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi11: spi@a8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart11: serial@a8c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c12: i2c@a90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi12: spi@a90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart12: serial@a90000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c16: i2c@a94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00a94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi16: spi@a94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00a94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart16: serial@a94000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00a94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_1 0 &qup_virt SLAVE_QUP_CORE_1 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		qupv3_id_2: geniqup@cc0000 {
			compatible = "qcom,geni-se-qup";
			reg = <0x0 0x00cc0000 0x0 0x6000>;
			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
			clock-names = "m-ahb", "s-ahb";
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			iommus = <&apps_smmu 0x7a3 0>;
			status = "disabled";

			i2c17: i2c@c80000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi17: spi@c80000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart17: serial@c80000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c80000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c18: i2c@c84000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi18: spi@c84000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart18: serial@c84000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c84000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c19: i2c@c88000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi19: spi@c88000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart19: serial@c88000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c88000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c13: i2c@c8c000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi13: spi@c8c000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart13: serial@c8c000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c8c000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c14: i2c@c90000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi14: spi@c90000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart14: serial@c90000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c90000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};

			i2c15: i2c@c94000 {
				compatible = "qcom,geni-i2c";
				reg = <0 0x00c94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>,
						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI_CH0 0>;
				interconnect-names = "qup-core", "qup-config", "qup-memory";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			spi15: spi@c94000 {
				compatible = "qcom,geni-spi";
				reg = <0 0x00c94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				#address-cells = <1>;
				#size-cells = <0>;
				status = "disabled";
			};

			uart15: serial@c94000 {
				compatible = "qcom,geni-uart";
				reg = <0 0x00c94000 0 0x4000>;
				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
				clock-names = "se";
				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
				interconnects = <&qup_virt MASTER_QUP_CORE_2 0 &qup_virt SLAVE_QUP_CORE_2 0>,
						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_2 0>;
				interconnect-names = "qup-core", "qup-config";
				status = "disabled";
			};
		};

		config_noc: interconnect@1500000 {
			compatible = "qcom,sc8180x-config-noc";
			reg = <0 0x01500000 0 0x7400>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		system_noc: interconnect@1620000 {
			compatible = "qcom,sc8180x-system-noc";
			reg = <0 0x01620000 0 0x19400>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre1_noc: interconnect@16e0000 {
			compatible = "qcom,sc8180x-aggre1-noc";
			reg = <0 0x016e0000 0 0xd080>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		aggre2_noc: interconnect@1700000 {
			compatible = "qcom,sc8180x-aggre2-noc";
			reg = <0 0x01700000 0 0x20000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		compute_noc: interconnect@1720000 {
			compatible = "qcom,sc8180x-compute-noc";
			reg = <0 0x01720000 0 0x7000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		mmss_noc: interconnect@1740000 {
			compatible = "qcom,sc8180x-mmss-noc";
			reg = <0 0x01740000 0 0x1c100>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		pcie0: pci@1c00000 {
			compatible = "qcom,pcie-sc8180x";
			reg = <0 0x01c00000 0 0x3000>,
			      <0 0x60000000 0 0xf1d>,
			      <0 0x60000f20 0 0xa8>,
			      <0 0x60001000 0 0x1000>,
			      <0 0x60100000 0 0x100000>;
			reg-names = "parf",
				    "dbi",
				    "elbi",
				    "atu",
				    "config";
			device_type = "pci";
			linux,pci-domain = <0>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x60200000 0x0 0x60200000 0x0 0x100000>,
				 <0x02000000 0x0 0x60300000 0x0 0x60300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
				 <&gcc GCC_PCIE_0_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu";

			assigned-clocks = <&gcc GCC_PCIE_0_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1d80 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1d80 0x1>,
				    <0x100 &apps_smmu 0x1d81 0x1>;

			resets = <&gcc GCC_PCIE_0_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_0_GDSC>;

			interconnects = <&aggre2_noc MASTER_PCIE 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			phys = <&pcie0_lane>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie0_phy: phy-wrapper@1c06000 {
			compatible = "qcom,sc8180x-qmp-pcie-phy";
			reg = <0 0x1c06000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie0_lane: phy@1c06200 {
				reg = <0 0x1c06200 0 0x170>, /* tx0 */
				      <0 0x1c06400 0 0x200>, /* rx0 */
				      <0 0x1c06a00 0 0x1f0>, /* pcs */
				      <0 0x1c06600 0 0x170>, /* tx1 */
				      <0 0x1c06800 0 0x200>, /* rx1 */
				      <0 0x1c06e00 0 0xf4>; /* pcs_com */
				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
				clock-names = "pipe0";

				#clock-cells = <0>;
				clock-output-names = "pcie_0_pipe_clk";
				#phy-cells = <0>;
			};
		};

		pcie3: pci@1c08000 {
			compatible = "qcom,pcie-sc8180x";
			reg = <0 0x01c08000 0 0x3000>,
			      <0 0x40000000 0 0xf1d>,
			      <0 0x40000f20 0 0xa8>,
			      <0 0x40001000 0 0x1000>,
			      <0 0x40100000 0 0x100000>;
			reg-names = "parf",
				    "dbi",
				    "elbi",
				    "atu",
				    "config";
			device_type = "pci";
			linux,pci-domain = <3>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;

			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_3_PIPE_CLK>,
				 <&gcc GCC_PCIE_3_AUX_CLK>,
				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_3_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_3_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_3_CLKREF_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu";

			assigned-clocks = <&gcc GCC_PCIE_3_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1e00 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1e00 0x1>,
				    <0x100 &apps_smmu 0x1e01 0x1>;

			resets = <&gcc GCC_PCIE_3_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_3_GDSC>;

			interconnects = <&aggre2_noc MASTER_PCIE_3 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			phys = <&pcie3_lane>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie3_phy: phy-wrapper@1c0c000 {
			compatible = "qcom,sc8180x-qmp-pcie-phy";
			reg = <0 0x1c0c000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_3_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_3_CLKREF_CLK>,
				 <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_3_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE3_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie3_lane: phy@1c0c200 {
				reg = <0 0x1c0c200 0 0x170>, /* tx0 */
				      <0 0x1c0c400 0 0x200>, /* rx0 */
				      <0 0x1c0ca00 0 0x1f0>, /* pcs */
				      <0 0x1c0c600 0 0x170>, /* tx1 */
				      <0 0x1c0c800 0 0x200>, /* rx1 */
				      <0 0x1c0ce00 0 0xf4>; /* pcs_com */
				clocks = <&gcc GCC_PCIE_3_PIPE_CLK>;
				clock-names = "pipe0";

				#clock-cells = <0>;
				clock-output-names = "pcie_3_pipe_clk";
				#phy-cells = <0>;
			};
		};

		pcie1: pci@1c10000 {
			compatible = "qcom,pcie-sc8180x";
			reg = <0 0x01c10000 0 0x3000>,
			      <0 0x68000000 0 0xf1d>,
			      <0 0x68000f20 0 0xa8>,
			      <0 0x68001000 0 0x1000>,
			      <0 0x68100000 0 0x100000>;
			reg-names = "parf",
				    "dbi",
				    "elbi",
				    "atu",
				    "config";
			device_type = "pci";
			linux,pci-domain = <1>;
			bus-range = <0x00 0xff>;
			num-lanes = <2>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x68200000 0x0 0x68200000 0x0 0x100000>,
				 <0x02000000 0x0 0x68300000 0x0 0x68300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 755 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 747 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 746 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 745 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 744 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
				 <&gcc GCC_PCIE_1_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu";

			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1c80 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
				    <0x100 &apps_smmu 0x1c81 0x1>;

			resets = <&gcc GCC_PCIE_1_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_1_GDSC>;

			interconnects = <&aggre2_noc MASTER_PCIE_1 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			phys = <&pcie1_lane>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie1_phy: phy-wrapper@1c16000 {
			compatible = "qcom,sc8180x-qmp-pcie-phy";
			reg = <0 0x1c16000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_1_CLKREF_CLK>,
				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie1_lane: phy@1c0e200 {
				reg = <0 0x1c16200 0 0x170>, /* tx0 */
				      <0 0x1c16400 0 0x200>, /* rx0 */
				      <0 0x1c16a00 0 0x1f0>, /* pcs */
				      <0 0x1c16600 0 0x170>, /* tx1 */
				      <0 0x1c16800 0 0x200>, /* rx1 */
				      <0 0x1c16e00 0 0xf4>; /* pcs_com */
				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
				clock-names = "pipe0";
				#clock-cells = <0>;
				clock-output-names = "pcie_1_pipe_clk";

				#phy-cells = <0>;
			};
		};

		pcie2: pci@1c18000 {
			compatible = "qcom,pcie-sc8180x";
			reg = <0 0x01c18000 0 0x3000>,
			      <0 0x70000000 0 0xf1d>,
			      <0 0x70000f20 0 0xa8>,
			      <0 0x70001000 0 0x1000>,
			      <0 0x70100000 0 0x100000>;
			reg-names = "parf",
				    "dbi",
				    "elbi",
				    "atu",
				    "config";
			device_type = "pci";
			linux,pci-domain = <2>;
			bus-range = <0x00 0xff>;
			num-lanes = <4>;

			#address-cells = <3>;
			#size-cells = <2>;

			ranges = <0x01000000 0x0 0x70200000 0x0 0x70200000 0x0 0x100000>,
				 <0x02000000 0x0 0x70300000 0x0 0x70300000 0x0 0x3d00000>;

			interrupts = <GIC_SPI 671 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "msi";
			#interrupt-cells = <1>;
			interrupt-map-mask = <0 0 0 0x7>;
			interrupt-map = <0 0 0 1 &intc 0 663 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
					<0 0 0 2 &intc 0 662 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
					<0 0 0 3 &intc 0 661 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
					<0 0 0 4 &intc 0 660 IRQ_TYPE_LEVEL_HIGH>; /* int_d */

			clocks = <&gcc GCC_PCIE_2_PIPE_CLK>,
				 <&gcc GCC_PCIE_2_AUX_CLK>,
				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
				 <&gcc GCC_PCIE_2_SLV_AXI_CLK>,
				 <&gcc GCC_PCIE_2_SLV_Q2A_AXI_CLK>,
				 <&gcc GCC_PCIE_2_CLKREF_CLK>,
				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
			clock-names = "pipe",
				      "aux",
				      "cfg",
				      "bus_master",
				      "bus_slave",
				      "slave_q2a",
				      "ref",
				      "tbu";

			assigned-clocks = <&gcc GCC_PCIE_2_AUX_CLK>;
			assigned-clock-rates = <19200000>;

			iommus = <&apps_smmu 0x1d00 0x7f>;
			iommu-map = <0x0   &apps_smmu 0x1d00 0x1>,
				    <0x100 &apps_smmu 0x1d01 0x1>;

			resets = <&gcc GCC_PCIE_2_BCR>;
			reset-names = "pci";

			power-domains = <&gcc PCIE_2_GDSC>;

			interconnects = <&aggre2_noc MASTER_PCIE_2 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_PCIE_0 0>;
			interconnect-names = "pcie-mem", "cpu-pcie";

			phys = <&pcie2_lane>;
			phy-names = "pciephy";

			status = "disabled";
		};

		pcie2_phy: phy-wrapper@1c1c000 {
			compatible = "qcom,sc8180x-qmp-pcie-phy";
			reg = <0 0x1c1c000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
				 <&gcc GCC_PCIE_2_CFG_AHB_CLK>,
				 <&gcc GCC_PCIE_2_CLKREF_CLK>,
				 <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
			clock-names = "aux", "cfg_ahb", "ref", "refgen";

			resets = <&gcc GCC_PCIE_2_PHY_BCR>;
			reset-names = "phy";

			assigned-clocks = <&gcc GCC_PCIE2_PHY_REFGEN_CLK>;
			assigned-clock-rates = <100000000>;

			status = "disabled";

			pcie2_lane: phy@1c0e200 {
				reg = <0 0x1c1c200 0 0x170>, /* tx0 */
				      <0 0x1c1c400 0 0x200>, /* rx0 */
				      <0 0x1c1ca00 0 0x1f0>, /* pcs */
				      <0 0x1c1c600 0 0x170>, /* tx1 */
				      <0 0x1c1c800 0 0x200>, /* rx1 */
				      <0 0x1c1ce00 0 0xf4>; /* pcs_com */
				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
				clock-names = "pipe0";

				#clock-cells = <0>;
				clock-output-names = "pcie_2_pipe_clk";

				#phy-cells = <0>;
			};
		};

		ufs_mem_hc: ufshc@1d84000 {
			compatible = "qcom,sc8180x-ufshc", "qcom,ufshc",
				     "jedec,ufs-2.0";
			reg = <0 0x01d84000 0 0x2500>;
			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
			phys = <&ufs_mem_phy_lanes>;
			phy-names = "ufsphy";
			lanes-per-direction = <2>;
			#reset-cells = <1>;
			resets = <&gcc GCC_UFS_PHY_BCR>;
			reset-names = "rst";

			iommus = <&apps_smmu 0x300 0>;

			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
				 <&gcc GCC_UFS_PHY_AHB_CLK>,
				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
			clock-names = "core_clk",
				      "bus_aggr_clk",
				      "iface_clk",
				      "core_clk_unipro",
				      "ref_clk",
				      "tx_lane0_sync_clk",
				      "rx_lane0_sync_clk",
				      "rx_lane1_sync_clk";
			freq-table-hz = <37500000 300000000>,
					<0 0>,
					<0 0>,
					<37500000 300000000>,
					<0 0>,
					<0 0>,
					<0 0>,
					<0 0>;

			status = "disabled";
		};

		ufs_mem_phy: phy-wrapper@1d87000 {
			compatible = "qcom,sc8180x-qmp-ufs-phy";
			reg = <0 0x01d87000 0 0x1c0>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
			clock-names = "ref",
				      "ref_aux";

			resets = <&ufs_mem_hc 0>;
			reset-names = "ufsphy";
			status = "disabled";

			ufs_mem_phy_lanes: phy@1d87400 {
				reg = <0 0x01d87400 0 0x108>,
				      <0 0x01d87600 0 0x1e0>,
				      <0 0x01d87c00 0 0x1dc>,
				      <0 0x01d87800 0 0x108>,
				      <0 0x01d87a00 0 0x1e0>;
				#phy-cells = <0>;
			};
		};

		ipa_virt: interconnect@1e00000 {
			compatible = "qcom,sc8180x-ipa-virt";
			reg = <0 0x01e00000 0 0x1000>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		tcsr_mutex: hwlock@1f40000 {
			compatible = "qcom,tcsr-mutex";
			reg = <0x0 0x01f40000 0x0 0x40000>;
			#hwlock-cells = <1>;
		};

		gpu: gpu@2c00000 {
			compatible = "qcom,adreno-680.1", "qcom,adreno";
			#stream-id-cells = <16>;

			reg = <0 0x02c00000 0 0x40000>;
			reg-names = "kgsl_3d0_reg_memory";

			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;

			iommus = <&adreno_smmu 0 0xc01>;

			operating-points-v2 = <&gpu_opp_table>;

			interconnects = <&gem_noc MASTER_GRAPHICS_3D 0 &mc_virt SLAVE_EBI_CH0 0>;
			interconnect-names = "gfx-mem";

			qcom,gmu = <&gmu>;
			status = "disabled";

			gpu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-514000000 {
					opp-hz = /bits/ 64 <514000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
				};

				opp-500000000 {
					opp-hz = /bits/ 64 <500000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
				};

				opp-461000000 {
					opp-hz = /bits/ 64 <461000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
				};

				opp-405000000 {
					opp-hz = /bits/ 64 <405000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
				};

				opp-315000000 {
					opp-hz = /bits/ 64 <315000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
				};

				opp-256000000 {
					opp-hz = /bits/ 64 <256000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
				};

				opp-177000000 {
					opp-hz = /bits/ 64 <177000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
				};
			};
		};

		gmu: gmu@2c6a000 {
			compatible="qcom,adreno-gmu-680.1", "qcom,adreno-gmu";

			reg = <0 0x02c6a000 0 0x30000>,
			      <0 0x0b290000 0 0x10000>,
			      <0 0x0b490000 0 0x10000>;
			reg-names = "gmu",
				    "gmu_pdc",
				    "gmu_pdc_seq";

			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hfi", "gmu";

			clocks = <&gpucc GPU_CC_AHB_CLK>,
				 <&gpucc GPU_CC_CX_GMU_CLK>,
				 <&gpucc GPU_CC_CXO_CLK>,
				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>;
			clock-names = "ahb", "gmu", "cxo", "axi", "memnoc";

			power-domains = <&gpucc GPU_CX_GDSC>,
					<&gpucc GPU_GX_GDSC>;
			power-domain-names = "cx", "gx";

			iommus = <&adreno_smmu 5 0xc00>;

			operating-points-v2 = <&gmu_opp_table>;

			gmu_opp_table: opp-table {
				compatible = "operating-points-v2";

				opp-200000000 {
					opp-hz = /bits/ 64 <200000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
				};

				opp-500000000 {
					opp-hz = /bits/ 64 <500000000>;
					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
				};
			};
		};

		gpucc: clock-controller@2c90000 {
			compatible = "qcom,sc8180x-gpucc";
			reg = <0 0x02c90000 0 0x9000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_GPU_GPLL0_CLK_SRC>,
				 <&gcc GCC_GPU_GPLL0_DIV_CLK_SRC>;
			clock-names = "bi_tcxo",
				      "gcc_gpu_gpll0_clk_src",
				      "gcc_gpu_gpll0_div_clk_src";
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		adreno_smmu: iommu@2ca0000 {
			compatible = "qcom,sc8180x-smmu-500", "qcom,adreno-smmu",
				     "qcom,smmu-500", "arm,mmu-500";
			reg = <0 0x02ca0000 0 0x10000>;
			#iommu-cells = <2>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 674 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 681 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 682 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 683 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 684 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 685 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 686 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 688 IRQ_TYPE_LEVEL_HIGH>;
			clocks = <&gpucc GPU_CC_AHB_CLK>,
				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>;
			clock-names = "ahb", "bus", "iface";

			power-domains = <&gpucc GPU_CX_GDSC>;
		};

		tlmm: pinctrl@3100000 {
			compatible = "qcom,sc8180x-tlmm";
			reg = <0 0x03100000 0 0x300000>,
			      <0 0x03500000 0 0x700000>,
			      <0 0x03d00000 0 0x300000>;
			reg-names = "west", "east", "south";
			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
			gpio-controller;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;
			gpio-ranges = <&tlmm 0 0 191>;
			wakeup-parent = <&pdc>;
		};

		remoteproc_mpss: remoteproc@4080000 {
			compatible = "qcom,sc8180x-mpss-pas";
			reg = <0x0 0x04080000 0x0 0x4040>;

			interrupts-extended = <&intc GIC_SPI 266 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready", "handover",
					  "stop-ack", "shutdown-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8180X_CX>,
					<&rpmhpd SC8180X_MSS>;
			power-domain-names = "cx", "mss";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&modem_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			glink-edge {
				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
				label = "modem";
				qcom,remote-pid = <1>;
				mboxes = <&apss_shared 12>;
			};
		};

		remoteproc_cdsp: remoteproc@8300000 {
			compatible = "qcom,sc8180x-cdsp-pas";
			reg = <0x0 0x08300000 0x0 0x4040>;

			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
					      <&cdsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&cdsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&cdsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&cdsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8180X_CX>;
			power-domain-names = "cx";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&cdsp_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			glink-edge {
				interrupts = <GIC_SPI 574 IRQ_TYPE_EDGE_RISING>;
				label = "cdsp";
				qcom,remote-pid = <5>;
				mboxes = <&apss_shared 4>;
			};
		};

		usb_prim_hsphy: phy@88e2000 {
			compatible = "qcom,sc8180x-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e2000 0 0x400>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_sec_hsphy: phy@88e3000 {
			compatible = "qcom,sc8180x-usb-hs-phy",
				     "qcom,usb-snps-hs-7nm-phy";
			reg = <0 0x088e3000 0 0x400>;
			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "ref";
			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;

			#phy-cells = <0>;

			status = "disabled";
		};

		usb_prim_qmpphy: phy@88e9000 {
			compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
			reg = <0 0x088e9000 0 0x18c>,
			      <0 0x088e8000 0 0x38>,
			      <0 0x088ea000 0 0x40>;
			reg-names = "reg-base", "dp_com";
			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
			clock-names = "aux",
				      "ref_clk_src",
				      "ref",
				      "com_aux";
			resets = <&gcc GCC_USB3_DP_PHY_PRIM_SP0_BCR>,
				 <&gcc GCC_USB3_PHY_PRIM_SP0_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			usb_prim_ssphy: usb3-phy@88e9200 {
				reg = <0 0x088e9200 0 0x200>,
				      <0 0x088e9400 0 0x200>,
				      <0 0x088e9c00 0 0x218>,
				      <0 0x088e9600 0 0x200>,
				      <0 0x088e9800 0 0x200>,
				      <0 0x088e9a00 0 0x100>;
				#phy-cells = <0>;
				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_prim_phy_pipe_clk_src";
			};

			usb_prim_dpphy: dp-phy@88ea200 {
				reg = <0 0x088ea200 0 0x200>,
				      <0 0x088ea400 0 0x200>,
				      <0 0x088eaa00 0 0x200>,
				      <0 0x088ea600 0 0x200>,
				      <0 0x088ea800 0 0x200>;
				#clock-cells = <1>;
				#phy-cells = <0>;
			};
		};

		usb_sec_qmpphy: phy@88ee000 {
			compatible = "qcom,sc8180x-qmp-usb3-dp-phy";
			reg = <0 0x088ee000 0 0x18c>,
			      <0 0x088ed000 0 0x10>,
			      <0 0x088ef000 0 0x40>;
			reg-names = "reg-base", "dp_com";
			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
				 <&rpmhcc RPMH_CXO_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_CLK>,
				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
			clock-names = "aux",
				      "ref_clk_src",
				      "ref",
				      "com_aux";
			resets = <&gcc GCC_USB3_DP_PHY_SEC_BCR>,
				 <&gcc GCC_USB3_PHY_SEC_BCR>;
			reset-names = "phy", "common";

			#clock-cells = <1>;
			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			usb_sec_ssphy: usb3-phy@88e9200 {
				reg = <0 0x088ee200 0 0x200>,
				      <0 0x088ee400 0 0x200>,
				      <0 0x088eec00 0 0x218>,
				      <0 0x088ee600 0 0x200>,
				      <0 0x088ee800 0 0x200>,
				      <0 0x088eea00 0 0x100>;
				#phy-cells = <0>;
				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
				clock-names = "pipe0";
				clock-output-names = "usb3_sec_phy_pipe_clk_src";
			};

			usb_sec_dpphy: dp-phy@88ef200 {
				reg = <0 0x088ef200 0 0x200>,
				      <0 0x088ef400 0 0x200>,
				      <0 0x088efa00 0 0x200>,
				      <0 0x088ef600 0 0x200>,
				      <0 0x088ef800 0 0x200>;
				#clock-cells = <1>;
				#phy-cells = <0>;
				clock-output-names = "qmp_dptx1_phy_pll_link_clk",
						     "qmp_dptx1_phy_pll_vco_div_clk";
			};
		};

		system-cache-controller@9200000 {
			compatible = "qcom,sc8180x-llcc";
			reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
			reg-names = "llcc_base", "llcc_broadcast_base";
			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
		};

		gem_noc: interconnect@9680000 {
			compatible = "qcom,sc8180x-gem-noc";
			reg = <0 0x09680000 0 0x58200>;
			#interconnect-cells = <2>;
			qcom,bcm-voters = <&apps_bcm_voter>;
		};

		usb_prim: usb@a6f8800 {
			compatible = "qcom,sc8180x-dwc3", "qcom,dwc3";
			reg = <0 0x0a6f8800 0 0x400>;
			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 488 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hs_phy_irq",
					  "ss_phy_irq",
					  "dm_hs_phy_irq",
					  "dp_hs_phy_irq";

			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "mock_utmi",
				      "sleep",
				      "xo";
			resets = <&gcc GCC_USB30_PRIM_BCR>;
			power-domains = <&gcc USB30_PRIM_GDSC>;

			interconnects = <&aggre1_noc MASTER_USB3 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			status = "disabled";

			usb_prim_dwc3: usb@a600000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a600000 0 0xcd00>;
				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x140 0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_prim_hsphy>, <&usb_prim_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		usb_sec: usb@a8f8800 {
			compatible = "qcom,sc8180x-dwc3", "qcom,dwc3";
			reg = <0 0x0a8f8800 0 0x400>;

			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
			clock-names = "cfg_noc",
				      "core",
				      "iface",
				      "mock_utmi",
				      "sleep",
				      "xo";
			resets = <&gcc GCC_USB30_SEC_BCR>;
			power-domains = <&gcc USB30_SEC_GDSC>;
			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "hs_phy_irq", "ss_phy_irq",
					  "dm_hs_phy_irq", "dp_hs_phy_irq";

			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
			assigned-clock-rates = <19200000>, <200000000>;

			interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3_1 0>;
			interconnect-names = "usb-ddr", "apps-usb";

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;
			dma-ranges;

			status = "disabled";

			usb_sec_dwc3: usb@a800000 {
				compatible = "snps,dwc3";
				reg = <0 0x0a800000 0 0xcd00>;
				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
				iommus = <&apps_smmu 0x160 0>;
				snps,dis_u2_susphy_quirk;
				snps,dis_enblslpm_quirk;
				phys = <&usb_sec_hsphy>, <&usb_sec_ssphy>;
				phy-names = "usb2-phy", "usb3-phy";
			};
		};

		mdss: mdss@ae00000 {
			compatible = "qcom,sc8180x-mdss";
			reg = <0 0x0ae00000 0 0x1000>;
			reg-names = "mdss";

			power-domains = <&dispcc MDSS_GDSC>;

			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
				 <&gcc GCC_DISP_HF_AXI_CLK>,
				 <&gcc GCC_DISP_SF_AXI_CLK>,
				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
			clock-names = "iface",
				      "bus",
				      "nrt_bus",
				      "core";

			resets = <&dispcc DISP_CC_MDSS_CORE_BCR>;

			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-controller;
			#interrupt-cells = <1>;

			interconnects = <&mmss_noc MASTER_MDP_PORT0 0 &mc_virt SLAVE_EBI_CH0 0>,
					<&mmss_noc MASTER_MDP_PORT1 0 &mc_virt SLAVE_EBI_CH0 0>;
			interconnect-names = "mdp0-mem", "mdp1-mem";

			iommus = <&apps_smmu 0x800 0x420>;

			#address-cells = <2>;
			#size-cells = <2>;
			ranges;

			status = "disabled";

			mdss_mdp: mdp@ae01000 {
				compatible = "qcom,sc8180x-dpu";
				reg = <0 0x0ae01000 0 0x8f000>,
				      <0 0x0aeb0000 0 0x2008>;
				reg-names = "mdp", "vbif";

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>,
					 <&dispcc DISP_CC_MDSS_MDP_CLK>,
					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				clock-names = "iface",
					      "bus",
					      "core",
					      "vsync";

				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
				assigned-clock-rates = <460000000>,
						       <19200000>;

				operating-points-v2 = <&mdp_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				interrupt-parent = <&mdss>;
				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dpu_intf0_out: endpoint {
							remote-endpoint = <&dp0_in>;
						};
					};

					port@1 {
						reg = <1>;
						dpu_intf1_out: endpoint {
							remote-endpoint = <&dsi0_in>;
						};
					};

					port@2 {
						reg = <2>;
						dpu_intf2_out: endpoint {
							remote-endpoint = <&dsi1_in>;
						};
					};

					port@4 {
						reg = <4>;
						dpu_intf4_out: endpoint {
							remote-endpoint = <&dp1_in>;
						};
					};

					port@5 {
						reg = <5>;
						dpu_intf5_out: endpoint {
							remote-endpoint = <&edp_in>;
						};
					};
				};

				mdp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-200000000 {
						opp-hz = /bits/ 64 <200000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-345000000 {
						opp-hz = /bits/ 64 <345000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-460000000 {
						opp-hz = /bits/ 64 <460000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			dsi0: dsi@ae94000 {
				compatible = "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae94000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				phys = <&dsi0_phy>;
				phy-names = "dsi";

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dsi0_in: endpoint {
							remote-endpoint = <&dpu_intf1_out>;
						};
					};

					port@1 {
						reg = <1>;
						dsi0_out: endpoint {
						};
					};
				};

				dsi_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-187500000 {
						opp-hz = /bits/ 64 <187500000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-300000000 {
						opp-hz = /bits/ 64 <300000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-358000000 {
						opp-hz = /bits/ 64 <358000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};
				};
			};

			dsi0_phy: dsi-phy@ae94400 {
				compatible = "qcom,dsi-phy-7nm";
				reg = <0 0x0ae94400 0 0x200>,
				      <0 0x0ae94600 0 0x280>,
				      <0 0x0ae94900 0 0x260>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			dsi1: dsi@ae96000 {
				compatible = "qcom,mdss-dsi-ctrl";
				reg = <0 0x0ae96000 0 0x400>;
				reg-names = "dsi_ctrl";

				interrupt-parent = <&mdss>;
				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;

				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_PCLK1_CLK>,
					 <&dispcc DISP_CC_MDSS_ESC1_CLK>,
					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&gcc GCC_DISP_HF_AXI_CLK>;
				clock-names = "byte",
					      "byte_intf",
					      "pixel",
					      "core",
					      "iface",
					      "bus";

				operating-points-v2 = <&dsi_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				phys = <&dsi1_phy>;
				phy-names = "dsi";

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dsi1_in: endpoint {
							remote-endpoint = <&dpu_intf2_out>;
						};
					};

					port@1 {
						reg = <1>;
						dsi1_out: endpoint {
						};
					};
				};
			};

			dsi1_phy: dsi-phy@ae96400 {
				compatible = "qcom,dsi-phy-7nm";
				reg = <0 0x0ae96400 0 0x200>,
				      <0 0x0ae96600 0 0x280>,
				      <0 0x0ae96900 0 0x260>;
				reg-names = "dsi_phy",
					    "dsi_phy_lane",
					    "dsi_pll";

				#clock-cells = <1>;
				#phy-cells = <0>;

				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&rpmhcc RPMH_CXO_CLK>;
				clock-names = "iface", "ref";

				status = "disabled";
			};

			mdss_dp0: displayport-controller@ae90000 {
				compatible = "qcom,sc8180x-dp";
				reg = <0 0xae90000 0 0x200>,
				      <0 0xae90200 0 0x200>,
				      <0 0xae90400 0 0x600>,
				      <0 0xae90a00 0 0x400>;
				interrupt-parent = <&mdss>;
				interrupts = <12>;
				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
				clock-names = "core_iface",
					      "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
				assigned-clock-parents = <&usb_prim_dpphy 0>, <&usb_prim_dpphy 1>;

				phys = <&usb_prim_dpphy>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&dp0_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dp0_in: endpoint {
							remote-endpoint = <&dpu_intf0_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				dp0_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_dp1: displayport-controller@ae98000 {
				compatible = "qcom,sc8180x-dp";
				reg = <0 0xae98000 0 0x200>,
				      <0 0xae98200 0 0x200>,
				      <0 0xae98400 0 0x600>,
				      <0 0xae98a00 0 0x400>;
				interrupt-parent = <&mdss>;
				interrupts = <13>;
				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_AUX1_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK1_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_LINK1_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK>;
				clock-names = "core_iface",
					      "core_aux",
					      "ctrl_link",
					      "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK1_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_DP_PIXEL2_CLK_SRC>;
				assigned-clock-parents = <&usb_sec_dpphy 0>, <&usb_sec_dpphy 1>;

				phys = <&usb_sec_dpphy>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&dp0_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						dp1_in: endpoint {
							remote-endpoint = <&dpu_intf4_out>;
						};
					};

					port@1 {
						reg = <1>;
					};
				};

				dp1_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};

			mdss_edp: displayport-controller@ae9a000 {
				compatible = "qcom,sc8180x-edp";
				reg = <0 0xae9a000 0 0x200>,
				      <0 0xae9a200 0 0x200>,
				      <0 0xae9a400 0 0x600>,
				      <0 0xae9aa00 0 0x400>;
				interrupt-parent = <&mdss>;
				interrupts = <14>;
				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
					 <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
					 <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
					 <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
					 <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
				clock-names = "core_iface",
					      "core_aux",
					      "ctrl_link",
					       "ctrl_link_iface",
					      "stream_pixel";

				assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
						  <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
				assigned-clock-parents = <&edp_phy 0>, <&edp_phy 1>;

				phys = <&edp_phy>;
				phy-names = "dp";

				#sound-dai-cells = <0>;

				operating-points-v2 = <&edp_opp_table>;
				power-domains = <&rpmhpd SC8180X_MMCX>;

				status = "disabled";

				ports {
					#address-cells = <1>;
					#size-cells = <0>;

					port@0 {
						reg = <0>;
						edp_in: endpoint {
							remote-endpoint = <&dpu_intf5_out>;
						};
					};
				};

				edp_opp_table: opp-table {
					compatible = "operating-points-v2";

					opp-160000000 {
						opp-hz = /bits/ 64 <160000000>;
						required-opps = <&rpmhpd_opp_low_svs>;
					};

					opp-270000000 {
						opp-hz = /bits/ 64 <270000000>;
						required-opps = <&rpmhpd_opp_svs>;
					};

					opp-540000000 {
						opp-hz = /bits/ 64 <540000000>;
						required-opps = <&rpmhpd_opp_svs_l1>;
					};

					opp-810000000 {
						opp-hz = /bits/ 64 <810000000>;
						required-opps = <&rpmhpd_opp_nom>;
					};
				};
			};
		};

		edp_phy: phy@aec2a00 {
			compatible = "qcom,sc8180x-edp-phy";
			reg = <0 0x0aec2a00 0 0x1c0>,
			      <0 0x0aec2200 0 0xa0>,
			      <0 0x0aec2600 0 0xa0>,
			      <0 0x0aec2000 0 0x19c>;

			clocks = <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
				 <&dispcc DISP_CC_MDSS_AHB_CLK>;
			clock-names = "aux", "cfg_ahb";

			power-domains = <&dispcc MDSS_GDSC>;

			#clock-cells = <1>;
			#phy-cells = <0>;
		};

		dispcc: clock-controller@af00000 {
			compatible = "qcom,sc8180x-dispcc";
			reg = <0 0x0af00000 0 0x20000>;
			clocks = <&rpmhcc RPMH_CXO_CLK>,
				 <&sleep_clk>,
				 <&usb_prim_dpphy 0>,
				 <&usb_prim_dpphy 1>,
				 <&usb_sec_dpphy 0>,
				 <&usb_sec_dpphy 1>,
				 <&edp_phy 0>,
				 <&edp_phy 1>;
			clock-names = "bi_tcxo",
				      "sleep_clk",
				      "dp_phy_pll_link_clk",
				      "dp_phy_pll_vco_div_clk",
				      "dptx1_phy_pll_link_clk",
				      "dptx1_phy_pll_vco_div_clk",
				      "edp_phy_pll_link_clk",
				      "edp_phy_pll_vco_div_clk";
			power-domains = <&rpmhpd SC8180X_MMCX>;
			#clock-cells = <1>;
			#reset-cells = <1>;
			#power-domain-cells = <1>;
		};

		pdc: interrupt-controller@b220000 {
			compatible = "qcom,sc8180x-pdc", "qcom,pdc";
			reg = <0 0x0b220000 0 0x30000>;
			qcom,pdc-ranges = <0 480 94>, <94 609 31>;
			#interrupt-cells = <2>;
			interrupt-parent = <&intc>;
			interrupt-controller;
		};

		tsens0: thermal-sensor@c263000 {
			compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
			reg = <0 0x0c263000 0 0x1ff>, /* TM */
			      <0 0x0c222000 0 0x1ff>; /* SROT */
			#qcom,sensors = <16>;
			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		tsens1: thermal-sensor@c265000 {
			compatible = "qcom,sc8180x-tsens", "qcom,tsens-v2";
			reg = <0 0x0c265000 0 0x1ff>, /* TM */
			      <0 0x0c223000 0 0x1ff>; /* SROT */
			#qcom,sensors = <9>;
			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
			interrupt-names = "uplow", "critical";
			#thermal-sensor-cells = <1>;
		};

		aoss_qmp: power-controller@c300000 {
			compatible = "qcom,sc8180x-aoss-qmp", "qcom,aoss-qmp";
			reg = <0x0 0x0c300000 0x0 0x100000>;
			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
			mboxes = <&apss_shared 0>;

			#clock-cells = <0>;
			#power-domain-cells = <1>;
		};

		spmi_bus: spmi@c440000 {
			compatible = "qcom,spmi-pmic-arb";
			reg = <0x0 0x0c440000 0x0 0x0001100>,
			      <0x0 0x0c600000 0x0 0x2000000>,
			      <0x0 0x0e600000 0x0 0x0100000>,
			      <0x0 0x0e700000 0x0 0x00a0000>,
			      <0x0 0x0c40a000 0x0 0x0026000>;
			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
			interrupt-names = "periph_irq";
			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>;
			qcom,ee = <0>;
			qcom,channel = <0>;
			#address-cells = <2>;
			#size-cells = <0>;
			interrupt-controller;
			#interrupt-cells = <4>;
			cell-index = <0>;
		};

		apps_smmu: iommu@15000000 {
			compatible = "qcom,sc8180x-smmu-500", "arm,mmu-500";
			reg = <0 0x15000000 0 0x100000>;
			#iommu-cells = <2>;
			#global-interrupts = <1>;
			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 708 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 709 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 710 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 711 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 712 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 713 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 715 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 768 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 769 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 770 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 771 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 772 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 773 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 774 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 775 IRQ_TYPE_LEVEL_HIGH>;

		};

		remoteproc_adsp: remoteproc@17300000 {
			compatible = "qcom,sc8180x-adsp-pas";
			reg = <0x0 0x17300000 0x0 0x4040>;

			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
			interrupt-names = "wdog", "fatal", "ready",
					  "handover", "stop-ack";

			clocks = <&rpmhcc RPMH_CXO_CLK>;
			clock-names = "xo";

			power-domains = <&rpmhpd SC8180X_CX>;
			power-domain-names = "cx";

			qcom,qmp = <&aoss_qmp>;

			qcom,smem-states = <&adsp_smp2p_out 0>;
			qcom,smem-state-names = "stop";

			status = "disabled";

			remoteproc_adsp_glink: glink-edge {
				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
				label = "lpass";
				qcom,remote-pid = <2>;
				mboxes = <&apss_shared 8>;
			};
		};

		intc: interrupt-controller@17a00000 {
			compatible = "arm,gic-v3";
			interrupt-controller;
			#interrupt-cells = <3>;
			reg = <0x0 0x17a00000 0x0 0x10000>,	/* GICD */
			      <0x0 0x17a60000 0x0 0x100000>;	/* GICR * 8 */
			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
		};

		apss_shared: mailbox@17c00000 {
			compatible = "qcom,sc8180x-apss-shared";
			reg = <0x0 0x17c00000 0x0 0x1000>;
			#mbox-cells = <1>;
		};

		timer@17c20000 {
			compatible = "arm,armv7-timer-mem";
			reg = <0x0 0x17c20000 0x0 0x1000>;

			#address-cells = <1>;
			#size-cells = <1>;
			ranges = <0 0 0 0x20000000>;

			frame@17c21000{
				reg = <0x17c21000 0x1000>,
				      <0x17c22000 0x1000>;
				frame-number = <0>;
				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
			};

			frame@17c23000 {
				reg = <0x17c23000 0x1000>;
				frame-number = <1>;
				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17c25000 {
				reg = <0x17c25000 0x1000>;
				frame-number = <2>;
				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17c27000 {
				reg = <0x17c26000 0x1000>;
				frame-number = <3>;
				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17c29000 {
				reg = <0x17c29000 0x1000>;
				frame-number = <4>;
				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17c2b000 {
				reg = <0x17c2b000 0x1000>;
				frame-number = <5>;
				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};

			frame@17c2d000 {
				reg = <0x17c2d000 0x1000>;
				frame-number = <6>;
				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
				status = "disabled";
			};
		};

		apps_rsc: rsc@18200000 {
			compatible = "qcom,rpmh-rsc";
			reg = <0x0 0x18200000 0x0 0x10000>,
			      <0x0 0x18210000 0x0 0x10000>,
			      <0x0 0x18220000 0x0 0x10000>;
			reg-names = "drv-0", "drv-1", "drv-2";
			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
			qcom,tcs-offset = <0xd00>;
			qcom,drv-id = <2>;
			qcom,tcs-config = <ACTIVE_TCS  2>,
					  <SLEEP_TCS   1>,
					  <WAKE_TCS    1>,
					  <CONTROL_TCS 0>;
			label = "apps_rsc";
			power-domains = <&CLUSTER_PD>;

			apps_bcm_voter: bcm-voter {
				compatible = "qcom,bcm-voter";
			};

			rpmhcc: clock-controller {
				compatible = "qcom,sc8180x-rpmh-clk";
				#clock-cells = <1>;
				clock-names = "xo";
				clocks = <&xo_board_clk>;
			};

			rpmhpd: power-controller {
				compatible = "qcom,sc8180x-rpmhpd";
				#power-domain-cells = <1>;
				operating-points-v2 = <&rpmhpd_opp_table>;

				rpmhpd_opp_table: opp-table {
					compatible = "operating-points-v2";

					rpmhpd_opp_ret: opp1 {
						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
					};

					rpmhpd_opp_min_svs: opp2 {
						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
					};

					rpmhpd_opp_low_svs: opp3 {
						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
					};

					rpmhpd_opp_svs: opp4 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
					};

					rpmhpd_opp_svs_l1: opp5 {
						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
					};

					rpmhpd_opp_nom: opp6 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
					};

					rpmhpd_opp_nom_l1: opp7 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
					};

					rpmhpd_opp_nom_l2: opp8 {
						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
					};

					rpmhpd_opp_turbo: opp9 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
					};

					rpmhpd_opp_turbo_l1: opp10 {
						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
					};
				};
			};
		};

		osm_l3: interconnect@18321000 {
			compatible = "qcom,sc8180x-osm-l3";
			reg = <0 0x18321000 0 0x1400>;

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";

			#interconnect-cells = <1>;
		};

		lmh@18350800 {
			compatible = "qcom,sc8180x-lmh";
			reg = <0 0x18350800 0 0x400>;
			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
			cpus = <&CPU4>;
			qcom,lmh-temp-arm-millicelsius = <65000>;
			qcom,lmh-temp-low-millicelsius = <94500>;
			qcom,lmh-temp-high-millicelsius = <95000>;
			interrupt-controller;
			#interrupt-cells = <1>;
		};

		lmh@18358800 {
			compatible = "qcom,sc8180x-lmh";
			reg = <0 0x18358800 0 0x400>;
			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
			cpus = <&CPU0>;
			qcom,lmh-temp-arm-millicelsius = <65000>;
			qcom,lmh-temp-low-millicelsius = <94500>;
			qcom,lmh-temp-high-millicelsius = <95000>;
			interrupt-controller;
			#interrupt-cells = <1>;
		};

		cpufreq_hw: cpufreq@18323000 {
			compatible = "qcom,cpufreq-hw";
			reg = <0 0x18323000 0 0x1400>, <0 0x18325800 0 0x1400>;
			reg-names = "freq-domain0", "freq-domain1";

			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
			clock-names = "xo", "alternate";

			#freq-domain-cells = <1>;
			#clock-cells = <1>;
		};

		wifi: wifi@18800000 {
			compatible = "qcom,wcn3990-wifi";
			reg = <0 0x18800000 0 0x800000>;
			reg-names = "membase";
			clock-names = "cxo_ref_clk_pin";
			clocks = <&rpmhcc RPMH_RF_CLK2>;
			interrupts = <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
			iommus = <&apps_smmu 0x0640 0x1>;
			qcom,msa-fixed-perm;
			status = "disabled";
		};
	};

	thermal-zones {
		cpu0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 1>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 2>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu2-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 3>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu3-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 4>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 7>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 8>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 9>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-top-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 10>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu4-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 11>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu5-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 12>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu6-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 13>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		cpu7-bottom-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 14>;

			trips {
				cpu-crit {
					temperature = <110000>;
					hysteresis = <1000>;
					type = "critical";
				};
			};
		};

		aoss0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 0>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		cluster0-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 5>;

			trips {
				cluster-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		cluster1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 6>;

			trips {
				cluster-crit {
					temperature = <110000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};

		gpu-thermal-top {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens0 15>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		aoss1-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 0>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		wlan-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 1>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		video-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 2>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mem-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 3>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		q6-hvx-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 4>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		camera-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 5>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		compute-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 6>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		mdm-dsp-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 7>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		npu-thermal {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 8>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};

		gpu-thermal-bottom {
			polling-delay-passive = <250>;
			polling-delay = <1000>;

			thermal-sensors = <&tsens1 11>;

			trips {
				trip-point0 {
					temperature = <90000>;
					hysteresis = <2000>;
					type = "hot";
				};
			};
		};
	};

	timer {
		compatible = "arm,armv8-timer";
		interrupts = <GIC_PPI 1 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 2 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 3 IRQ_TYPE_LEVEL_LOW>,
			     <GIC_PPI 0 IRQ_TYPE_LEVEL_LOW>;
	};
};