xref: /openbmc/linux/arch/arm/mm/proc-arm1022.S (revision 4b4193256c8d3bc3a5397b5cd9494c2ad386317d)

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
 *  linux/arch/arm/mm/proc-arm1022.S: MMU functions for ARM1022E
 *
 *  Copyright (C) 2000 ARM Limited
 *  Copyright (C) 2000 Deep Blue Solutions Ltd.
 *  hacked for non-paged-MM by Hyok S. Choi, 2003.
 *
 * These are the low level assembler for performing cache and TLB
 * functions on the ARM1022E.
 */
#include <linux/linkage.h>
#include <linux/init.h>
#include <linux/pgtable.h>
#include <asm/assembler.h>
#include <asm/asm-offsets.h>
#include <asm/hwcap.h>
#include <asm/pgtable-hwdef.h>
#include <asm/ptrace.h>

#include "proc-macros.S"

/*
 * This is the maximum size of an area which will be invalidated
 * using the single invalidate entry instructions.  Anything larger
 * than this, and we go for the whole cache.
 *
 * This value should be chosen such that we choose the cheapest
 * alternative.
 */
#define MAX_AREA_SIZE	32768

/*
 * The size of one data cache line.
 */
#define CACHE_DLINESIZE	32

/*
 * The number of data cache segments.
 */
#define CACHE_DSEGMENTS	16

/*
 * The number of lines in a cache segment.
 */
#define CACHE_DENTRIES	64

/*
 * This is the size at which it becomes more efficient to
 * clean the whole cache, rather than using the individual
 * cache line maintenance instructions.
 */
#define CACHE_DLIMIT	32768

	.text
/*
 * cpu_arm1022_proc_init()
 */
ENTRY(cpu_arm1022_proc_init)
	ret	lr

/*
 * cpu_arm1022_proc_fin()
 */
ENTRY(cpu_arm1022_proc_fin)
	mrc	p15, 0, r0, c1, c0, 0		@ ctrl register
	bic	r0, r0, #0x1000 		@ ...i............
	bic	r0, r0, #0x000e 		@ ............wca.
	mcr	p15, 0, r0, c1, c0, 0		@ disable caches
	ret	lr

/*
 * cpu_arm1022_reset(loc)
 *
 * Perform a soft reset of the system.	Put the CPU into the
 * same state as it would be if it had been reset, and branch
 * to what would be the reset vector.
 *
 * loc: location to jump to for soft reset
 */
	.align	5
	.pushsection	.idmap.text, "ax"
ENTRY(cpu_arm1022_reset)
	mov	ip, #0
	mcr	p15, 0, ip, c7, c7, 0		@ invalidate I,D caches
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
#ifdef CONFIG_MMU
	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I & D TLBs
#endif
	mrc	p15, 0, ip, c1, c0, 0		@ ctrl register
	bic	ip, ip, #0x000f 		@ ............wcam
	bic	ip, ip, #0x1100 		@ ...i...s........
	mcr	p15, 0, ip, c1, c0, 0		@ ctrl register
	ret	r0
ENDPROC(cpu_arm1022_reset)
	.popsection

/*
 * cpu_arm1022_do_idle()
 */
	.align	5
ENTRY(cpu_arm1022_do_idle)
	mcr	p15, 0, r0, c7, c0, 4		@ Wait for interrupt
	ret	lr

/* ================================= CACHE ================================ */

	.align	5

/*
 *	flush_icache_all()
 *
 *	Unconditionally clean and invalidate the entire icache.
 */
ENTRY(arm1022_flush_icache_all)
#ifndef CONFIG_CPU_ICACHE_DISABLE
	mov	r0, #0
	mcr	p15, 0, r0, c7, c5, 0		@ invalidate I cache
#endif
	ret	lr
ENDPROC(arm1022_flush_icache_all)

/*
 *	flush_user_cache_all()
 *
 *	Invalidate all cache entries in a particular address
 *	space.
 */
ENTRY(arm1022_flush_user_cache_all)
	/* FALLTHROUGH */
/*
 *	flush_kern_cache_all()
 *
 *	Clean and invalidate the entire cache.
 */
ENTRY(arm1022_flush_kern_cache_all)
	mov	r2, #VM_EXEC
	mov	ip, #0
__flush_whole_cache:
#ifndef CONFIG_CPU_DCACHE_DISABLE
	mov	r1, #(CACHE_DSEGMENTS - 1) << 5	@ 16 segments
1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
2:	mcr	p15, 0, r3, c7, c14, 2		@ clean+invalidate D index
	subs	r3, r3, #1 << 26
	bcs	2b				@ entries 63 to 0
	subs	r1, r1, #1 << 5
	bcs	1b				@ segments 15 to 0
#endif
	tst	r2, #VM_EXEC
#ifndef CONFIG_CPU_ICACHE_DISABLE
	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
#endif
	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	flush_user_cache_range(start, end, flags)
 *
 *	Invalidate a range of cache entries in the specified
 *	address space.
 *
 *	- start	- start address (inclusive)
 *	- end	- end address (exclusive)
 *	- flags	- vm_flags for this space
 */
ENTRY(arm1022_flush_user_cache_range)
	mov	ip, #0
	sub	r3, r1, r0			@ calculate total size
	cmp	r3, #CACHE_DLIMIT
	bhs	__flush_whole_cache

#ifndef CONFIG_CPU_DCACHE_DISABLE
1:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
#endif
	tst	r2, #VM_EXEC
#ifndef CONFIG_CPU_ICACHE_DISABLE
	mcrne	p15, 0, ip, c7, c5, 0		@ invalidate I cache
#endif
	mcrne	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	coherent_kern_range(start, end)
 *
 *	Ensure coherency between the Icache and the Dcache in the
 *	region described by start.  If you have non-snooping
 *	Harvard caches, you need to implement this function.
 *
 *	- start	- virtual start address
 *	- end	- virtual end address
 */
ENTRY(arm1022_coherent_kern_range)
	/* FALLTHROUGH */

/*
 *	coherent_user_range(start, end)
 *
 *	Ensure coherency between the Icache and the Dcache in the
 *	region described by start.  If you have non-snooping
 *	Harvard caches, you need to implement this function.
 *
 *	- start	- virtual start address
 *	- end	- virtual end address
 */
ENTRY(arm1022_coherent_user_range)
	mov	ip, #0
	bic	r0, r0, #CACHE_DLINESIZE - 1
1:
#ifndef CONFIG_CPU_DCACHE_DISABLE
	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
#endif
#ifndef CONFIG_CPU_ICACHE_DISABLE
	mcr	p15, 0, r0, c7, c5, 1		@ invalidate I entry
#endif
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
	mov	r0, #0
	ret	lr

/*
 *	flush_kern_dcache_area(void *addr, size_t size)
 *
 *	Ensure no D cache aliasing occurs, either with itself or
 *	the I cache
 *
 *	- addr	- kernel address
 *	- size	- region size
 */
ENTRY(arm1022_flush_kern_dcache_area)
	mov	ip, #0
#ifndef CONFIG_CPU_DCACHE_DISABLE
	add	r1, r0, r1
1:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
#endif
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	dma_inv_range(start, end)
 *
 *	Invalidate (discard) the specified virtual address range.
 *	May not write back any entries.  If 'start' or 'end'
 *	are not cache line aligned, those lines must be written
 *	back.
 *
 *	- start	- virtual start address
 *	- end	- virtual end address
 *
 * (same as v4wb)
 */
arm1022_dma_inv_range:
	mov	ip, #0
#ifndef CONFIG_CPU_DCACHE_DISABLE
	tst	r0, #CACHE_DLINESIZE - 1
	bic	r0, r0, #CACHE_DLINESIZE - 1
	mcrne	p15, 0, r0, c7, c10, 1		@ clean D entry
	tst	r1, #CACHE_DLINESIZE - 1
	mcrne	p15, 0, r1, c7, c10, 1		@ clean D entry
1:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate D entry
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
#endif
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	dma_clean_range(start, end)
 *
 *	Clean the specified virtual address range.
 *
 *	- start	- virtual start address
 *	- end	- virtual end address
 *
 * (same as v4wb)
 */
arm1022_dma_clean_range:
	mov	ip, #0
#ifndef CONFIG_CPU_DCACHE_DISABLE
	bic	r0, r0, #CACHE_DLINESIZE - 1
1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
#endif
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	dma_flush_range(start, end)
 *
 *	Clean and invalidate the specified virtual address range.
 *
 *	- start	- virtual start address
 *	- end	- virtual end address
 */
ENTRY(arm1022_dma_flush_range)
	mov	ip, #0
#ifndef CONFIG_CPU_DCACHE_DISABLE
	bic	r0, r0, #CACHE_DLINESIZE - 1
1:	mcr	p15, 0, r0, c7, c14, 1		@ clean+invalidate D entry
	add	r0, r0, #CACHE_DLINESIZE
	cmp	r0, r1
	blo	1b
#endif
	mcr	p15, 0, ip, c7, c10, 4		@ drain WB
	ret	lr

/*
 *	dma_map_area(start, size, dir)
 *	- start	- kernel virtual start address
 *	- size	- size of region
 *	- dir	- DMA direction
 */
ENTRY(arm1022_dma_map_area)
	add	r1, r1, r0
	cmp	r2, #DMA_TO_DEVICE
	beq	arm1022_dma_clean_range
	bcs	arm1022_dma_inv_range
	b	arm1022_dma_flush_range
ENDPROC(arm1022_dma_map_area)

/*
 *	dma_unmap_area(start, size, dir)
 *	- start	- kernel virtual start address
 *	- size	- size of region
 *	- dir	- DMA direction
 */
ENTRY(arm1022_dma_unmap_area)
	ret	lr
ENDPROC(arm1022_dma_unmap_area)

	.globl	arm1022_flush_kern_cache_louis
	.equ	arm1022_flush_kern_cache_louis, arm1022_flush_kern_cache_all

	@ define struct cpu_cache_fns (see <asm/cacheflush.h> and proc-macros.S)
	define_cache_functions arm1022

	.align	5
ENTRY(cpu_arm1022_dcache_clean_area)
#ifndef CONFIG_CPU_DCACHE_DISABLE
	mov	ip, #0
1:	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
	add	r0, r0, #CACHE_DLINESIZE
	subs	r1, r1, #CACHE_DLINESIZE
	bhi	1b
#endif
	ret	lr

/* =============================== PageTable ============================== */

/*
 * cpu_arm1022_switch_mm(pgd)
 *
 * Set the translation base pointer to be as described by pgd.
 *
 * pgd: new page tables
 */
	.align	5
ENTRY(cpu_arm1022_switch_mm)
#ifdef CONFIG_MMU
#ifndef CONFIG_CPU_DCACHE_DISABLE
	mov	r1, #(CACHE_DSEGMENTS - 1) << 5	@ 16 segments
1:	orr	r3, r1, #(CACHE_DENTRIES - 1) << 26 @ 64 entries
2:	mcr	p15, 0, r3, c7, c14, 2		@ clean+invalidate D index
	subs	r3, r3, #1 << 26
	bcs	2b				@ entries 63 to 0
	subs	r1, r1, #1 << 5
	bcs	1b				@ segments 15 to 0
#endif
	mov	r1, #0
#ifndef CONFIG_CPU_ICACHE_DISABLE
	mcr	p15, 0, r1, c7, c5, 0		@ invalidate I cache
#endif
	mcr	p15, 0, r1, c7, c10, 4		@ drain WB
	mcr	p15, 0, r0, c2, c0, 0		@ load page table pointer
	mcr	p15, 0, r1, c8, c7, 0		@ invalidate I & D TLBs
#endif
	ret	lr

/*
 * cpu_arm1022_set_pte_ext(ptep, pte, ext)
 *
 * Set a PTE and flush it out
 */
	.align	5
ENTRY(cpu_arm1022_set_pte_ext)
#ifdef CONFIG_MMU
	armv3_set_pte_ext
	mov	r0, r0
#ifndef CONFIG_CPU_DCACHE_DISABLE
	mcr	p15, 0, r0, c7, c10, 1		@ clean D entry
#endif
#endif /* CONFIG_MMU */
	ret	lr

	.type	__arm1022_setup, #function
__arm1022_setup:
	mov	r0, #0
	mcr	p15, 0, r0, c7, c7		@ invalidate I,D caches on v4
	mcr	p15, 0, r0, c7, c10, 4		@ drain write buffer on v4
#ifdef CONFIG_MMU
	mcr	p15, 0, r0, c8, c7		@ invalidate I,D TLBs on v4
#endif
	adr	r5, arm1022_crval
	ldmia	r5, {r5, r6}
	mrc	p15, 0, r0, c1, c0		@ get control register v4
	bic	r0, r0, r5
	orr	r0, r0, r6
#ifdef CONFIG_CPU_CACHE_ROUND_ROBIN
	orr	r0, r0, #0x4000 		@ .R..............
#endif
	ret	lr
	.size	__arm1022_setup, . - __arm1022_setup

	/*
	 *  R
	 * .RVI ZFRS BLDP WCAM
	 * .011 1001 ..11 0101
	 *
	 */
	.type	arm1022_crval, #object
arm1022_crval:
	crval	clear=0x00007f3f, mmuset=0x00003935, ucset=0x00001930

	__INITDATA
	@ define struct processor (see <asm/proc-fns.h> and proc-macros.S)
	define_processor_functions arm1022, dabort=v4t_early_abort, pabort=legacy_pabort

	.section ".rodata"

	string	cpu_arch_name, "armv5te"
	string	cpu_elf_name, "v5"
	string	cpu_arm1022_name, "ARM1022"

	.align

	.section ".proc.info.init", "a"

	.type	__arm1022_proc_info,#object
__arm1022_proc_info:
	.long	0x4105a220			@ ARM 1022E (v5TE)
	.long	0xff0ffff0
	.long   PMD_TYPE_SECT | \
		PMD_BIT4 | \
		PMD_SECT_AP_WRITE | \
		PMD_SECT_AP_READ
	.long   PMD_TYPE_SECT | \
		PMD_BIT4 | \
		PMD_SECT_AP_WRITE | \
		PMD_SECT_AP_READ
	initfn	__arm1022_setup, __arm1022_proc_info
	.long	cpu_arch_name
	.long	cpu_elf_name
	.long	HWCAP_SWP | HWCAP_HALF | HWCAP_THUMB | HWCAP_EDSP
	.long	cpu_arm1022_name
	.long	arm1022_processor_functions
	.long	v4wbi_tlb_fns
	.long	v4wb_user_fns
	.long	arm1022_cache_fns
	.size	__arm1022_proc_info, . - __arm1022_proc_info