xref: /openbmc/linux/Documentation/firmware-guide/acpi/gpio-properties.rst (revision 8b31e972f9872e5a6a3348506b5b84353fecef58)

.. SPDX-License-Identifier: GPL-2.0

======================================
_DSD Device Properties Related to GPIO
======================================

With the release of ACPI 5.1, the _DSD configuration object finally
allows names to be given to GPIOs (and other things as well) returned
by _CRS.  Previously, we were only able to use an integer index to find
the corresponding GPIO, which is pretty error prone (it depends on
the _CRS output ordering, for example).

With _DSD we can now query GPIOs using a name instead of an integer
index, like the ASL example below shows::

  // Bluetooth device with reset and shutdown GPIOs
  Device (BTH)
  {
      Name (_HID, ...)

      Name (_CRS, ResourceTemplate ()
      {
          GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionOutputOnly,
                  "\\_SB.GPO0", 0, ResourceConsumer) {15}
          GpioIo (Exclusive, PullUp, 0, 0, IoRestrictionOutputOnly,
                  "\\_SB.GPO0", 0, ResourceConsumer) {27, 31}
      })

      Name (_DSD, Package ()
      {
          ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
          Package ()
	  {
              Package () {"reset-gpios", Package() {^BTH, 1, 1, 0 }},
              Package () {"shutdown-gpios", Package() {^BTH, 0, 0, 0 }},
          }
      })
  }

The format of the supported GPIO property is::

  Package () { "name", Package () { ref, index, pin, active_low }}

ref
  The device that has _CRS containing GpioIo()/GpioInt() resources,
  typically this is the device itself (BTH in our case).
index
  Index of the GpioIo()/GpioInt() resource in _CRS starting from zero.
pin
  Pin in the GpioIo()/GpioInt() resource. Typically this is zero.
active_low
  If 1, the GPIO is marked as active_low.

Since ACPI GpioIo() resource does not have a field saying whether it is
active low or high, the "active_low" argument can be used here.  Setting
it to 1 marks the GPIO as active low.

Note, active_low in _DSD does not make sense for GpioInt() resource and
must be 0. GpioInt() resource has its own means of defining it.

In our Bluetooth example the "reset-gpios" refers to the second GpioIo()
resource, second pin in that resource with the GPIO number of 31.

The GpioIo() resource unfortunately doesn't explicitly provide an initial
state of the output pin which driver should use during its initialization.

Linux tries to use common sense here and derives the state from the bias
and polarity settings. The table below shows the expectations:

=========  =============  ==============
Pull Bias     Polarity     Requested...
=========  =============  ==============
Implicit     x            AS IS (assumed firmware configured for us)
Explicit     x (no _DSD)  as Pull Bias (Up == High, Down == Low),
                          assuming non-active (Polarity = !Pull Bias)
Down         Low          as low, assuming active
Down         High         as low, assuming non-active
Up           Low          as high, assuming non-active
Up           High         as high, assuming active
=========  =============  ==============

That said, for our above example the both GPIOs, since the bias setting
is explicit and _DSD is present, will be treated as active with a high
polarity and Linux will configure the pins in this state until a driver
reprograms them differently.

It is possible to leave holes in the array of GPIOs. This is useful in
cases like with SPI host controllers where some chip selects may be
implemented as GPIOs and some as native signals. For example a SPI host
controller can have chip selects 0 and 2 implemented as GPIOs and 1 as
native::

  Package () {
      "cs-gpios",
      Package () {
          ^GPIO, 19, 0, 0, // chip select 0: GPIO
          0,               // chip select 1: native signal
          ^GPIO, 20, 0, 0, // chip select 2: GPIO
      }
  }

Other supported properties
==========================

Following Device Tree compatible device properties are also supported by
_DSD device properties for GPIO controllers:

- gpio-hog
- output-high
- output-low
- input
- line-name

Example::

  Name (_DSD, Package () {
      // _DSD Hierarchical Properties Extension UUID
      ToUUID("dbb8e3e6-5886-4ba6-8795-1319f52a966b"),
      Package () {
          Package () {"hog-gpio8", "G8PU"}
      }
  })

  Name (G8PU, Package () {
      ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
      Package () {
          Package () {"gpio-hog", 1},
          Package () {"gpios", Package () {8, 0}},
          Package () {"output-high", 1},
          Package () {"line-name", "gpio8-pullup"},
      }
  })

- gpio-line-names

Example::

  Package () {
      "gpio-line-names",
      Package () {
          "SPI0_CS_N", "EXP2_INT", "MUX6_IO", "UART0_RXD",
          "MUX7_IO", "LVL_C_A1", "MUX0_IO", "SPI1_MISO",
      }
  }

See Documentation/devicetree/bindings/gpio/gpio.txt for more information
about these properties.

ACPI GPIO Mappings Provided by Drivers
======================================

There are systems in which the ACPI tables do not contain _DSD but provide _CRS
with GpioIo()/GpioInt() resources and device drivers still need to work with
them.

In those cases ACPI device identification objects, _HID, _CID, _CLS, _SUB, _HRV,
available to the driver can be used to identify the device and that is supposed
to be sufficient to determine the meaning and purpose of all of the GPIO lines
listed by the GpioIo()/GpioInt() resources returned by _CRS.  In other words,
the driver is supposed to know what to use the GpioIo()/GpioInt() resources for
once it has identified the device.  Having done that, it can simply assign names
to the GPIO lines it is going to use and provide the GPIO subsystem with a
mapping between those names and the ACPI GPIO resources corresponding to them.

To do that, the driver needs to define a mapping table as a NULL-terminated
array of struct acpi_gpio_mapping objects that each contains a name, a pointer
to an array of line data (struct acpi_gpio_params) objects and the size of that
array.  Each struct acpi_gpio_params object consists of three fields,
crs_entry_index, line_index, active_low, representing the index of the target
GpioIo()/GpioInt() resource in _CRS starting from zero, the index of the target
line in that resource starting from zero, and the active-low flag for that line,
respectively, in analogy with the _DSD GPIO property format specified above.

For the example Bluetooth device discussed previously the data structures in
question would look like this::

  static const struct acpi_gpio_params reset_gpio = { 1, 1, false };
  static const struct acpi_gpio_params shutdown_gpio = { 0, 0, false };

  static const struct acpi_gpio_mapping bluetooth_acpi_gpios[] = {
    { "reset-gpios", &reset_gpio, 1 },
    { "shutdown-gpios", &shutdown_gpio, 1 },
    { }
  };

Next, the mapping table needs to be passed as the second argument to
acpi_dev_add_driver_gpios() or its managed analogue that will
register it with the ACPI device object pointed to by its first
argument. That should be done in the driver's .probe() routine.
On removal, the driver should unregister its GPIO mapping table by
calling acpi_dev_remove_driver_gpios() on the ACPI device object where that
table was previously registered.

Using the _CRS fallback
=======================

If a device does not have _DSD or the driver does not create ACPI GPIO
mapping, the Linux GPIO framework refuses to return any GPIOs. This is
because the driver does not know what it actually gets. For example if we
have a device like below::

  Device (BTH)
  {
      Name (_HID, ...)

      Name (_CRS, ResourceTemplate () {
          GpioIo (Exclusive, PullNone, 0, 0, IoRestrictionNone,
                  "\\_SB.GPO0", 0, ResourceConsumer) {15}
          GpioIo (Exclusive, PullNone, 0, 0, IoRestrictionNone,
                  "\\_SB.GPO0", 0, ResourceConsumer) {27}
      })
  }

The driver might expect to get the right GPIO when it does::

  desc = gpiod_get(dev, "reset", GPIOD_OUT_LOW);

but since there is no way to know the mapping between "reset" and
the GpioIo() in _CRS desc will hold ERR_PTR(-ENOENT).

The driver author can solve this by passing the mapping explicitly
(this is the recommended way and it's documented in the above chapter).

The ACPI GPIO mapping tables should not contaminate drivers that are not
knowing about which exact device they are servicing on. It implies that
the ACPI GPIO mapping tables are hardly linked to an ACPI ID and certain
objects, as listed in the above chapter, of the device in question.

Getting GPIO descriptor
=======================

There are two main approaches to get GPIO resource from ACPI::

  desc = gpiod_get(dev, connection_id, flags);
  desc = gpiod_get_index(dev, connection_id, index, flags);

We may consider two different cases here, i.e. when connection ID is
provided and otherwise.

Case 1::

  desc = gpiod_get(dev, "non-null-connection-id", flags);
  desc = gpiod_get_index(dev, "non-null-connection-id", index, flags);

Case 2::

  desc = gpiod_get(dev, NULL, flags);
  desc = gpiod_get_index(dev, NULL, index, flags);

Case 1 assumes that corresponding ACPI device description must have
defined device properties and will prevent to getting any GPIO resources
otherwise.

Case 2 explicitly tells GPIO core to look for resources in _CRS.

Be aware that gpiod_get_index() in cases 1 and 2, assuming that there
are two versions of ACPI device description provided and no mapping is
present in the driver, will return different resources. That's why a
certain driver has to handle them carefully as explained in the previous
chapter.