xref: /openbmc/linux/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml (revision 4f2c0a4acffbec01079c28f839422e64ddeff004)

# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/phy/nvidia,tegra20-usb-phy.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: NVIDIA Tegra USB PHY

maintainers:
  - Dmitry Osipenko <digetx@gmail.com>
  - Jon Hunter <jonathanh@nvidia.com>
  - Thierry Reding <thierry.reding@gmail.com>

properties:
  compatible:
    oneOf:
      - items:
          - enum:
              - nvidia,tegra124-usb-phy
              - nvidia,tegra114-usb-phy
          - enum:
              - nvidia,tegra30-usb-phy
      - items:
          - enum:
              - nvidia,tegra30-usb-phy
              - nvidia,tegra20-usb-phy

  reg:
    minItems: 1
    maxItems: 2
    description: |
      PHY0 and PHY2 share power and ground, PHY0 contains shared registers.
      PHY0 and PHY2 must specify two register sets, where the first set is
      PHY own registers and the second set is the PHY0 registers.

  clocks:
    anyOf:
      - items:
          - description: Registers clock
          - description: Main PHY clock

      - items:
          - description: Registers clock
          - description: Main PHY clock
          - description: ULPI PHY clock

      - items:
          - description: Registers clock
          - description: Main PHY clock
          - description: UTMI pads control registers clock

      - items:
          - description: Registers clock
          - description: Main PHY clock
          - description: UTMI timeout clock
          - description: UTMI pads control registers clock

  clock-names:
    oneOf:
      - items:
          - const: reg
          - const: pll_u

      - items:
          - const: reg
          - const: pll_u
          - const: ulpi-link

      - items:
          - const: reg
          - const: pll_u
          - const: utmi-pads

      - items:
          - const: reg
          - const: pll_u
          - const: timer
          - const: utmi-pads

  interrupts:
    maxItems: 1

  resets:
    oneOf:
      - maxItems: 1
        description: PHY reset

      - items:
          - description: PHY reset
          - description: UTMI pads reset

  reset-names:
    oneOf:
      - const: usb

      - items:
          - const: usb
          - const: utmi-pads

  "#phy-cells":
    const: 0

  phy_type:
    $ref: /schemas/types.yaml#/definitions/string
    enum: [utmi, ulpi, hsic]

  dr_mode:
    $ref: /schemas/types.yaml#/definitions/string
    enum: [host, peripheral, otg]
    default: host

  vbus-supply:
    description: Regulator controlling USB VBUS.

  nvidia,has-legacy-mode:
    description: |
      Indicates whether this controller can operate in legacy mode
      (as APX 2500 / 2600). In legacy mode some registers are accessed
      through the APB_MISC base address instead of the USB controller.
    type: boolean

  nvidia,is-wired:
    description: |
      Indicates whether we can do certain kind of power optimizations for
      the devices that are always connected. e.g. modem.
    type: boolean

  nvidia,has-utmi-pad-registers:
    description: |
      Indicates whether this controller contains the UTMI pad control
      registers common to all USB controllers.
    type: boolean

  nvidia,hssync-start-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 31
    description: |
      Number of 480 MHz clock cycles to wait before start of sync launches
      RxActive.

  nvidia,elastic-limit:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 31
    description: Variable FIFO Depth of elastic input store.

  nvidia,idle-wait-delay:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 31
    description: |
      Number of 480 MHz clock cycles of idle to wait before declare IDLE.

  nvidia,term-range-adj:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 15
    description: Range adjustment on terminations.

  nvidia,xcvr-setup:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 127
    description: Input of XCVR cell, HS driver output control.

  nvidia,xcvr-setup-use-fuses:
    description: Indicates that the value is read from the on-chip fuses.
    type: boolean

  nvidia,xcvr-lsfslew:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 3
    description: LS falling slew rate control.

  nvidia,xcvr-lsrslew:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 3
    description: LS rising slew rate control.

  nvidia,xcvr-hsslew:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 511
    description: HS slew rate control.

  nvidia,hssquelch-level:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 3
    description: HS squelch detector level.

  nvidia,hsdiscon-level:
    $ref: /schemas/types.yaml#/definitions/uint32
    minimum: 0
    maximum: 7
    description: HS disconnect detector level.

  nvidia,phy-reset-gpio:
    maxItems: 1
    description: GPIO used to reset the PHY.

  nvidia,pmc:
    $ref: /schemas/types.yaml#/definitions/phandle-array
    items:
      - items:
          - description: Phandle to Power Management controller.
          - description: USB controller ID.
    description:
      Phandle to Power Management controller.

required:
  - compatible
  - reg
  - clocks
  - clock-names
  - resets
  - reset-names
  - "#phy-cells"
  - phy_type

additionalProperties: false

allOf:
  - if:
      properties:
        phy_type:
          const: utmi

    then:
      properties:
        reg:
          minItems: 2
          maxItems: 2

        resets:
          maxItems: 2

        reset-names:
          maxItems: 2

      required:
        - nvidia,hssync-start-delay
        - nvidia,elastic-limit
        - nvidia,idle-wait-delay
        - nvidia,term-range-adj
        - nvidia,xcvr-lsfslew
        - nvidia,xcvr-lsrslew

      anyOf:
        - required: ["nvidia,xcvr-setup"]
        - required: ["nvidia,xcvr-setup-use-fuses"]

      if:
        properties:
          compatible:
            contains:
              const: nvidia,tegra30-usb-phy

      then:
        properties:
          clocks:
            maxItems: 3

          clock-names:
            items:
              - const: reg
              - const: pll_u
              - const: utmi-pads

        required:
          - nvidia,xcvr-hsslew
          - nvidia,hssquelch-level
          - nvidia,hsdiscon-level

      else:
        properties:
          clocks:
            maxItems: 4

          clock-names:
            items:
              - const: reg
              - const: pll_u
              - const: timer
              - const: utmi-pads

  - if:
      properties:
        phy_type:
          const: ulpi

    then:
      properties:
        reg:
          minItems: 1
          maxItems: 1

        clocks:
          minItems: 2
          maxItems: 3

        clock-names:
          minItems: 2
          maxItems: 3

          oneOf:
            - items:
                - const: reg
                - const: pll_u

            - items:
                - const: reg
                - const: pll_u
                - const: ulpi-link

        resets:
          minItems: 1
          maxItems: 2

        reset-names:
          minItems: 1
          maxItems: 2

examples:
  - |
    #include <dt-bindings/clock/tegra124-car.h>

    usb-phy@7d008000 {
        compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy";
        reg = <0x7d008000 0x4000>,
              <0x7d000000 0x4000>;
        interrupts = <0 97 4>;
        phy_type = "utmi";
        clocks = <&tegra_car TEGRA124_CLK_USB3>,
                 <&tegra_car TEGRA124_CLK_PLL_U>,
                 <&tegra_car TEGRA124_CLK_USBD>;
        clock-names = "reg", "pll_u", "utmi-pads";
        resets = <&tegra_car 59>, <&tegra_car 22>;
        reset-names = "usb", "utmi-pads";
        #phy-cells = <0>;
        nvidia,hssync-start-delay = <0>;
        nvidia,idle-wait-delay = <17>;
        nvidia,elastic-limit = <16>;
        nvidia,term-range-adj = <6>;
        nvidia,xcvr-setup = <9>;
        nvidia,xcvr-lsfslew = <0>;
        nvidia,xcvr-lsrslew = <3>;
        nvidia,hssquelch-level = <2>;
        nvidia,hsdiscon-level = <5>;
        nvidia,xcvr-hsslew = <12>;
        nvidia,pmc = <&tegra_pmc 2>;
    };

  - |
    #include <dt-bindings/clock/tegra20-car.h>

    usb-phy@c5004000 {
        compatible = "nvidia,tegra20-usb-phy";
        reg = <0xc5004000 0x4000>;
        interrupts = <0 21 4>;
        phy_type = "ulpi";
        clocks = <&tegra_car TEGRA20_CLK_USB2>,
                 <&tegra_car TEGRA20_CLK_PLL_U>,
                 <&tegra_car TEGRA20_CLK_CDEV2>;
        clock-names = "reg", "pll_u", "ulpi-link";
        resets = <&tegra_car 58>, <&tegra_car 22>;
        reset-names = "usb", "utmi-pads";
        #phy-cells = <0>;
        nvidia,pmc = <&tegra_pmc 1>;
    };