| /openbmc/openbmc/meta-facebook/meta-yosemite4/recipes-yosemite4/plat-svc/files/ |
| H A D | yosemite4-early-sys-init | 10 if find /sys/bus/i2c/devices/*/hwmon/*/fan*_enable -print -quit 2>/dev/null | grep -q .; then
11 for file in /sys/bus/i2c/devices/*/hwmon/*/fan*_enable
24 if [[ ! "$pwm_node" =~ _enable ]]; then
|
| /openbmc/linux/drivers/clk/sunxi-ng/ |
| H A D | ccu_frac.h | 20 #define _SUNXI_CCU_FRAC(_enable, _select, _rate1, _rate2) \ argument
22 .enable = _enable, \
|
| H A D | ccu_sdm.h | 41 #define _SUNXI_CCU_SDM(_table, _enable, \ argument
46 .enable = _enable, \
|
| /openbmc/openbmc/meta-facebook/meta-catalina/recipes-catalina/plat-svc/files/ |
| H A D | catalina-early-sys-init | 34 if find /sys/bus/i2c/devices/*/hwmon/*/fan*_enable -print -quit 2>/dev/null | grep -q .; then
35 for file in /sys/bus/i2c/devices/*/hwmon/*/fan*_enable
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | max31790.rst | 41 fan[1-6]_enable RW enable or disable the tachometer input
42 pwm[1-6]_enable RW regulator mode, 0=disabled (duty cycle=0%), 1=manual mode, 2=rpm mode
|
| H A D | gxp-fan-ctrl.rst | 27 fan[0-7]_enable Fan 0 to 7 respective enabled status: 1 enabled, 0 disabled
|
| H A D | sysfs-interface.rst | 147 `in[0-*]_enable`
190 `fan[1-*]_enable`
203 `pwm[1-*]_enable`
294 `temp[1-*]_enable`
351 `curr[1-*]_enable`
436 `power[1-*]_enable`
474 `energy[1-*]_enable`
492 `humidity[1-*]_enable`
|
| H A D | tps23861.rst | 40 in[0-3]_enable Enable/disable ports [1-4]
|
| H A D | max31730.rst | 34 temp[1-4]_enable RW Temperature enable/disable
|
| H A D | nct7904.rst | 44 pwm[1-4]_enable R/W, 1/2 for manual or SmartFan mode
|
| H A D | tmp464.rst | 64 **temp[1-9]_enable**
|
| H A D | w83l786ng.rst | 53 pwm[1-2]_enable
|
| H A D | tmp421.rst | 71 **temp[1-4]_enable**
|
| H A D | max31785.rst | 56 pwm[1-4]_enable 0: Full-speed
|
| H A D | ina3221.rst | 31 in[123]_enable Voltage channel enable controls
|
| H A D | nzxt-smart2.rst | 54 pwm[1-3]_enable 1 if the fan can be controlled by writing to the
|
| H A D | max31760.rst | 62 fan[1-2]_enable Enable fan readings and fan fault alarms
|
| H A D | asc7621.rst | 201 temp[5-8]_input / temp[5-8]_enable
207 pwm[1-3]_enable
|
| H A D | dme1737.rst | 307 pwm[1-3]_enable RW Enable of PWM outputs 1-3. Supported
313 pwm[5-6]_enable RO Enable of PWM outputs 5-6. Always
|
| H A D | f71882fg.rst | 171 to the pwm#_enable file. Note that not all modes are supported on all
|
| H A D | w83792d.rst | 180 pwm[1-3]_enable
|
| H A D | w83791d.rst | 131 pwm[1-3]_enable this file controls mode of fan/temperature control for
|
| /openbmc/linux/arch/mips/alchemy/common/ |
| H A D | platform.c | 288 #define MAC_RES(_base, _enable, _irq, _macdma) \ argument
295 .start = _enable, \
296 .end = _enable + 0x3, \
|
| /openbmc/linux/drivers/staging/iio/frequency/ |
| H A D | dds.h | 94 IIO_DEVICE_ATTR(out_altvoltage##_channel##_out##_output##_enable,\
|
| /openbmc/linux/arch/arm/mach-omap2/ |
| H A D | omap_hwmod.c | 1865 static int _enable(struct omap_hwmod *oh) in _enable() function
2043 _enable(oh); in _shutdown()
2054 _enable(oh); in _shutdown()
2411 r = _enable(oh); in _setup_reset()
2517 r = _enable(oh->parent_hwmod); in _setup()
3677 r = _enable(oh); in omap_hwmod_enable()
|