| /openbmc/linux/drivers/usb/atm/ |
| H A D | Kconfig | 3 # USB/ATM DSL configuration
7 tristate "USB DSL modem support"
11 Say Y here if you want to connect a USB Digital Subscriber Line (DSL)
45 tristate "ADI 930 and eagle USB DSL modem"
57 tristate "Other USB DSL modem support"
59 Say Y here if you have a DSL USB modem not explicitly supported by
60 another USB DSL drivers. In order to use your modem you will need to
|
| /openbmc/linux/drivers/clk/bcm/ |
| H A D | Kconfig | 29 Enable common clock framework support for Broadcom BCM63xx DSL SoCs
37 Enable common clock framework support for Broadcom BCM63xx DSL SoCs
46 Enable timer clock and reset support for Broadcom BCM63268 DSL SoCs
|
| /openbmc/linux/Documentation/devicetree/bindings/arm/bcm/ |
| H A D | brcm,bcm63138.txt | 1 Broadcom BCM63138 DSL System-on-a-Chip device tree bindings
4 Boards compatible with the BCM63138 DSL System-on-a-Chip should have the
|
| /openbmc/openbmc/poky/meta/recipes-devtools/python/ |
| H A D | python3-booleanpy_4.0.bb | 1 …ARY = "Define boolean algebras, create and parse boolean expressions and create custom boolean DSL"
|
| /openbmc/linux/arch/arm/mach-bcm/ |
| H A D | Kconfig | 213 including the DSL, PON and Wireless family of chips.
226 including various DSL, PON and Wireless family of chips.
242 only DSL chip BCM63138.
252 only DSL chip BCM63148.
|
| /openbmc/linux/drivers/isdn/ |
| H A D | Kconfig | 15 (though still much slower than with DSL) or to make and accept
|
| /openbmc/linux/Documentation/devicetree/bindings/sound/ |
| H A D | brcm,bcm63xx-audio.txt | 1 Broadcom DSL/PON BCM63xx Audio I2S controller
|
| /openbmc/linux/sound/soc/bcm/ |
| H A D | Kconfig | 26 DSL/PON chips (bcm63158, bcm63178)
|
| /openbmc/linux/drivers/mtd/nand/raw/brcmnand/ |
| H A D | Kconfig | 17 on Broadcom BCM63xx MIPS-based DSL platforms.
|
| /openbmc/linux/include/sound/ |
| H A D | emu10k1.h | 451 #define DSL 0x07 /* Send D amount and loop end address register */ macro
452 SUB_REG(DSL, FXSENDAMOUNT_D, 0xff000000) /* Linear level of channel output sent to FX send bus D */
453 SUB_REG(DSL, LOOPENDADDR, 0x00ffffff) /* Loop end address of the specified channel */
|
| /openbmc/linux/net/atm/ |
| H A D | Kconfig | 66 This is sometimes used over DSL lines. If in doubt, say N.
|
| /openbmc/linux/arch/arm/boot/dts/broadcom/ |
| H A D | bcm63138.dtsi | 3 * Broadcom BCM63138 DSL SoCs Device Tree
|
| /openbmc/linux/drivers/net/ethernet/dec/tulip/ |
| H A D | de2104x.c | 83 #define DSL 0 macro
85 #define DSL CONFIG_DE2104X_DSL macro
159 DescSkipLen = (DSL << 2),
274 #if DSL
275 __le32 skip[DSL];
|
| /openbmc/linux/Documentation/devicetree/bindings/mips/brcm/ |
| H A D | soc.txt | 1 * Broadcom cable/DSL/settop platforms
|
| /openbmc/linux/arch/arm/boot/dts/marvell/ |
| H A D | kirkwood-l-50.dts | 76 * 1: DSL module reset (active low)
|
| /openbmc/linux/sound/pci/emu10k1/ |
| H A D | emu10k1_callback.c | 420 DSL, dsl, in start_voice()
|
| H A D | emu10k1_main.c | 61 DSL, 0x10, in snd_emu10k1_voice_init()
1759 CPF, PTRX, CVCF, VTFT, Z1, Z2, PSST, DSL, CCCA, CCR, CLP,
|
| H A D | emuproc.c | 87 dsl = snd_emu10k1_ptr_read(emu, DSL, idx); in snd_emu10k1_proc_read()
|
| H A D | emupcm.c | 302 DSL, end_addr | (send_amount[3] << 24), in snd_emu10k1_pcm_init_voice()
|
| /openbmc/linux/arch/arm64/ |
| H A D | Kconfig.platforms | 71 including the DSL, PON and Wireless family of chips.
|
| /openbmc/linux/drivers/atm/ |
| H A D | Kconfig | 38 have the code to drive the on-board Alcatel DSL chipset (yet).
|
| /openbmc/linux/drivers/i2c/busses/ |
| H A D | Kconfig | 493 tristate "BRCM Settop/DSL I2C controller"
499 I2C interface on the Broadcom Settop/DSL SoCs.
|
| /openbmc/openbmc/poky/documentation/migration-guides/ |
| H A D | release-notes-4.3.rst | 106 algebras, create and parse boolean expressions and create custom boolean DSL
|
| /openbmc/linux/drivers/tty/serial/ |
| H A D | Kconfig | 1074 BCM63xx/BCM63xxx (DSL)
|
| /openbmc/linux/drivers/gpio/ |
| H A D | Kconfig | 627 Some of the GPIOs/LEDs can be auto updated by the SoC with DSL and
|