Searched hist:fa588eba632df14d296436995e6bbea0c146ae77 (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/net/wwan/ |
| H A D | mhi_wwan_ctrl.c | fa588eba632df14d296436995e6bbea0c146ae77 Fri Apr 16 03:36:34 CDT 2021 Loic Poulain <loic.poulain@linaro.org> net: Add Qcom WWAN control driver
The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
(qmi-firmware-update)
Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | Makefile | diff fa588eba632df14d296436995e6bbea0c146ae77 Fri Apr 16 03:36:34 CDT 2021 Loic Poulain <loic.poulain@linaro.org> net: Add Qcom WWAN control driver
The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
(qmi-firmware-update)
Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| H A D | Kconfig | diff fa588eba632df14d296436995e6bbea0c146ae77 Fri Apr 16 03:36:34 CDT 2021 Loic Poulain <loic.poulain@linaro.org> net: Add Qcom WWAN control driver
The MHI WWWAN control driver allows MHI QCOM-based modems to expose
different modem control protocols/ports via the WWAN framework, so that
userspace modem tools or daemon (e.g. ModemManager) can control WWAN
config and state (APN config, SMS, provider selection...). A QCOM-based
modem can expose one or several of the following protocols:
- AT: Well known AT commands interactive protocol (microcom, minicom...)
- MBIM: Mobile Broadband Interface Model (libmbim, mbimcli)
- QMI: QCOM MSM/Modem Interface (libqmi, qmicli)
- QCDM: QCOM Modem diagnostic interface (libqcdm)
- FIREHOSE: XML-based protocol for Modem firmware management
(qmi-firmware-update)
Note that this patch is mostly a rework of the earlier MHI UCI
tentative that was a generic interface for accessing MHI bus from
userspace. As suggested, this new version is WWAN specific and is
dedicated to only expose channels used for controlling a modem, and
for which related opensource userpace support exist.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|