| /openbmc/linux/drivers/acpi/acpica/ |
| H A D | rsdumpinfo.c | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | rsinfo.c | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | rsserial.c | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | acresrc.h | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | amlresrc.h | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | utresrc.c | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | rscalc.c | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | acutils.h | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| H A D | aclocal.h | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
| /openbmc/linux/include/acpi/ |
| H A D | acrestyp.h | diff 97028ce6fca0fec53ee71e2fd5acfb2dc8430f1f Mon Jun 05 03:39:19 CDT 2017 Mika Westerberg <mika.westerberg@linux.intel.com> ACPICA: ACPI 6.2: Add support for PinConfig() resource
ACPICA commit a06fdba686cefccd5dd5b93b52fa0f1e3f984906
ACPI 6.2 introduced a new resource that is used to specify fine-grained
configuration of a pin or set of pins used by a device. The ASL syntax of
this new resource looks like:
PinConfig (Shared/Exclusive, PinConfigType, PinConfigValue,
ResourceSource, ResourceSourceIndex, ResourceUsage,
DescriptorName, Vendordata) {Pin List}
PinConfigType is an integer with following accepted values:
0x00 (Default) - No configuration is applied to the pin
0x01 (Bias Pull-up) - Pin is pulled up using certain size resistor
0x02 (Bias Pull-down) - Pin is pulled down using certain size resistor
0x03 (Bias Default) - Set to default biasing
0x04 (Bias Disable) - All bias settings will be disabled
0x05 (Bias High Impedance) - Configure the pin as hi_z
0x06 (Bias Bus Hold) - Configure the pin in a weak latch state where
it drives the last value on a tristate bus
0x07 (Drive Open Drain) - Configure the pin into open drain state
0x08 (Drive Open Source) - Configure the pin into open source state
0x09 (Drive Push Pull) - Configure the pin into push-pull state
0x0a (Drive Strength) - How much the pin can supply current
0x0b (Slew Rate) - Configure slew rate of the pin
0x0c (Input Debounce) - Enable input debouncer for the pin
0x0d (Input Schmitt Trigger) - Enable schmitt trigger for the pin
0x0e - 0x7f - Reserved
0x80 - 0xff - Vendor defined types
The PinConfigValue depends on the type and is expressed as units
suitable for that type (for example bias uses Ohms).
Link: https://github.com/acpica/acpica/commit/a06fdba6
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|