Searched hist:"954 d6235be412e3de33a43e68ab39342f5eccf9b" (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/s390/cio/ |
| H A D | qdio_thinint.c | diff 954d6235be412e3de33a43e68ab39342f5eccf9b Wed Sep 30 03:09:07 CDT 2020 Julian Wiedmann <jwi@linux.ibm.com> s390/qdio: make thinint registration symmetric
tiqdio_add_device() adds the device to the tiq_list of eligible targets
for a data IRQ, which gets walked on each QDIO Adapter Interrupt to
inspect their DSCIs.
But currently the tiqdio_add_device() / tiqdio_remove_device() calls
are not symmetric - the device is removed within qdio_shutdown(),
but only added by qdio_activate().
So depending on the call sequence and encountered errors, we might
be trying to remove a list entry in qdio_shutdown() that was never even
added to the list. This required additional INIT_LIST_HEAD() calls to
ensure that the list entry was always in a consistent state.
All drivers now fence the IRQ delivery via qdio_start_irq() /
qdio_stop_irq(), so we can nicely integrate this tiq_list management
with the other steps needed for QDIO Adapter IRQ (de-)registration
(qdio_establish_thinint() / qdio_shutdown_thinint()).
As the naming suggests these get called during qdio_establish() and
qdio_shutdown(), with proper symmetry and roll-back after errors.
With this we longer need to worry about misplaced list removals, and
thus can clean up the list API abuse (INIT_LIST_HEAD() should not be
called on list entries).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
| H A D | qdio.h | diff 954d6235be412e3de33a43e68ab39342f5eccf9b Wed Sep 30 03:09:07 CDT 2020 Julian Wiedmann <jwi@linux.ibm.com> s390/qdio: make thinint registration symmetric
tiqdio_add_device() adds the device to the tiq_list of eligible targets
for a data IRQ, which gets walked on each QDIO Adapter Interrupt to
inspect their DSCIs.
But currently the tiqdio_add_device() / tiqdio_remove_device() calls
are not symmetric - the device is removed within qdio_shutdown(),
but only added by qdio_activate().
So depending on the call sequence and encountered errors, we might
be trying to remove a list entry in qdio_shutdown() that was never even
added to the list. This required additional INIT_LIST_HEAD() calls to
ensure that the list entry was always in a consistent state.
All drivers now fence the IRQ delivery via qdio_start_irq() /
qdio_stop_irq(), so we can nicely integrate this tiq_list management
with the other steps needed for QDIO Adapter IRQ (de-)registration
(qdio_establish_thinint() / qdio_shutdown_thinint()).
As the naming suggests these get called during qdio_establish() and
qdio_shutdown(), with proper symmetry and roll-back after errors.
With this we longer need to worry about misplaced list removals, and
thus can clean up the list API abuse (INIT_LIST_HEAD() should not be
called on list entries).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
| H A D | qdio_main.c | diff 954d6235be412e3de33a43e68ab39342f5eccf9b Wed Sep 30 03:09:07 CDT 2020 Julian Wiedmann <jwi@linux.ibm.com> s390/qdio: make thinint registration symmetric
tiqdio_add_device() adds the device to the tiq_list of eligible targets
for a data IRQ, which gets walked on each QDIO Adapter Interrupt to
inspect their DSCIs.
But currently the tiqdio_add_device() / tiqdio_remove_device() calls
are not symmetric - the device is removed within qdio_shutdown(),
but only added by qdio_activate().
So depending on the call sequence and encountered errors, we might
be trying to remove a list entry in qdio_shutdown() that was never even
added to the list. This required additional INIT_LIST_HEAD() calls to
ensure that the list entry was always in a consistent state.
All drivers now fence the IRQ delivery via qdio_start_irq() /
qdio_stop_irq(), so we can nicely integrate this tiq_list management
with the other steps needed for QDIO Adapter IRQ (de-)registration
(qdio_establish_thinint() / qdio_shutdown_thinint()).
As the naming suggests these get called during qdio_establish() and
qdio_shutdown(), with proper symmetry and roll-back after errors.
With this we longer need to worry about misplaced list removals, and
thus can clean up the list API abuse (INIT_LIST_HEAD() should not be
called on list entries).
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|