Searched hist:"069 a2e37789a9adb236d8f7a5f65a1390b51f184" (Results 1 – 1 of 1) sorted by relevance
| /openbmc/linux/fs/btrfs/ |
| H A D | ctree.c | diff 069a2e37789a9adb236d8f7a5f65a1390b51f184 Tue Jul 20 10:03:03 CDT 2021 Filipe Manana <fdmanana@suse.com> btrfs: continue readahead of siblings even if target node is in memory
At reada_for_search(), when attempting to readahead a node or leaf's
siblings, we skip the readahead of the siblings if the node/leaf is
already in memory. That is probably fine for the READA_FORWARD and
READA_BACK readahead types, as they are used on contexts where we
end up reading some consecutive leaves, but usually not the whole btree.
However for a READA_FORWARD_ALWAYS mode, currently only used for full
send operations, it does not make sense to skip the readahead if the
target node or leaf is already loaded in memory, since we know the caller
is visiting every node and leaf of the btree in ascending order.
So change the behaviour to not skip the readahead when the target node is
already in memory and the readahead mode is READA_FORWARD_ALWAYS.
The following test script was used to measure the improvement on a box
using an average, consumer grade, spinning disk, with 32GiB of RAM and
using a non-debug kernel config (Debian's default config).
$ cat test.sh
#!/bin/bash
DEV=/dev/sdj
MNT=/mnt/sdj
MKFS_OPTIONS="--nodesize 16384" # default, just to be explicit
MOUNT_OPTIONS="-o max_inline=2048" # default, just to be explicit
mkfs.btrfs -f $MKFS_OPTIONS $DEV > /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
# Create files with inline data to make it easier and faster to create
# large btrees.
add_files()
{
local total=$1
local start_offset=$2
local number_jobs=$3
local total_per_job=$(($total / $number_jobs))
echo "Creating $total new files using $number_jobs jobs"
for ((n = 0; n < $number_jobs; n++)); do
(
local start_num=$(($start_offset + $n * $total_per_job))
for ((i = 1; i <= $total_per_job; i++)); do
local file_num=$((start_num + $i))
local file_path="$MNT/file_${file_num}"
xfs_io -f -c "pwrite -S 0xab 0 2000" $file_path > /dev/null
if [ $? -ne 0 ]; then
echo "Failed creating file $file_path"
break
fi
done
) &
worker_pids[$n]=$!
done
wait ${worker_pids[@]}
sync
echo
echo "btree node/leaf count: $(btrfs inspect-internal dump-tree -t 5 $DEV | egrep '^(node|leaf) ' | wc -l)"
}
file_count=2000000
add_files $file_count 0 4
echo
echo "Creating snapshot..."
btrfs subvolume snapshot -r $MNT $MNT/snap1
umount $MNT
echo 3 > /proc/sys/vm/drop_caches
blockdev --flushbufs $DEV &> /dev/null
hdparm -F $DEV &> /dev/null
mount $MOUNT_OPTIONS $DEV $MNT
echo
echo "Testing full send..."
start=$(date +%s)
btrfs send $MNT/snap1 > /dev/null
end=$(date +%s)
echo
echo "Full send took $((end - start)) seconds"
umount $MNT
The duration of the full send operations, in seconds, were the following:
Before this change: 85 seconds
After this change: 76 seconds (-11.2%)
Reviewed-by: Qu Wenruo <wqu@suse.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|