| /openbmc/libmctp/tests/ |
| H A D | test_astlpc.c | 208 /* BMC initialisation */ in network_init()
214 /* Host initialisation */ in network_init()
250 /* Test harness initialisation */ in astlpc_test_packetised_message_bmc_to_host()
293 /* Test harness initialisation */ in astlpc_test_simple_message_host_to_bmc()
335 /* Test harness initialisation */ in astlpc_test_simple_message_bmc_to_host()
448 /* Test harness initialisation */ in astlpc_test_version_host_fails_negotiation()
452 /* BMC initialisation */ in astlpc_test_version_host_fails_negotiation()
461 /* Host initialisation */ in astlpc_test_version_host_fails_negotiation()
479 /* Test harness initialisation */ in astlpc_test_version_bmc_fails_negotiation()
483 /* BMC initialisation */ in astlpc_test_version_bmc_fails_negotiation()
[all …]
|
| /openbmc/linux/Documentation/arch/arm/ |
| H A D | setup.rst | 2 Kernel initialisation parameters on ARM Linux
5 The following document describes the kernel initialisation parameter
9 This structure is used to pass initialisation parameters from the
11 through the kernel initialisation process. As a general rule, it
|
| /openbmc/linux/include/linux/regulator/ |
| H A D | userspace-consumer.h | 9 * initialisation data.
15 * enabled during initialisation
|
| H A D | machine.h | 154 * initialisation.
246 * struct regulator_init_data - regulator platform initialisation data.
248 * Initialisation constraints, our supply and consumers supplies.
|
| /openbmc/u-boot/board/efi/ |
| H A D | Kconfig | 11 this case EFI does the early initialisation, and U-Boot
19 this case EFI does the early initialisation, and U-Boot
|
| /openbmc/linux/drivers/hwtracing/coresight/ |
| H A D | coresight-cfg-preload.c | 11 /* Basic features and configurations pre-loaded on initialisation */
31 /* preload called on initialisation */
|
| /openbmc/linux/include/xen/interface/io/ |
| H A D | xenbus.h | 14 status of initialisation across the bus. States here imply nothing about
22 initialisation, but waiting
|
| /openbmc/qemu/include/hw/xen/interface/io/ |
| H A D | xenbus.h | 15 * status of initialisation across the bus. States here imply nothing about
25 * InitWait: Finished early initialisation but waiting for information
|
| /openbmc/linux/arch/arm/mach-s3c/ |
| H A D | cpu.h | 57 /* per-cpu initialisation function table. */
71 /* core initialisation functions */
|
| H A D | init.c | 7 // S3C series CPU initialisation
80 * early initialisation of the console.
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | cirrus,lochnagar.yaml | 143 Initialisation data for the VDDCORE regulator, which supplies the
161 Initialisation data for the MICVDD regulator, which supplies the
179 Initialisation data for the MIC1VDD supplies.
205 Initialisation data for the MIC2VDD supplies.
|
| /openbmc/linux/sound/aoa/ |
| H A D | aoa-gpio.h | 24 /* for initialisation/de-initialisation of the GPIO layer */
|
| /openbmc/linux/include/pcmcia/ |
| H A D | soc_common.h | 97 * Enable card status IRQs on (re-)initialisation. This can
98 * be called at initialisation, power management event, or
|
| /openbmc/linux/Documentation/power/regulator/ |
| H A D | machine.rst | 6 initialisation code to configure the regulator subsystem.
16 initialisation code by creating a struct regulator_consumer_supply for
|
| /openbmc/linux/drivers/mfd/ |
| H A D | wm8400-core.c | 45 * wm8400_init - Generic initialisation
91 dev_warn(wm8400->dev, "No platform initialisation supplied\n"); in wm8400_init()
|
| /openbmc/linux/arch/x86/include/asm/ |
| H A D | setup_arch.h | 1 /* Hook to call BIOS initialisation function */
|
| /openbmc/linux/drivers/firmware/efi/ |
| H A D | memmap.c | 110 * The reason there are two EFI memmap initialisation
113 * initialisation is complete as the fixmap space used to map the EFI
|
| /openbmc/libmctp/docs/bindings/ |
| H A D | vendor-ibm-astlpc.md | 279 The BMC MAY choose to fail channel initialisation if these properties are
311 The host sends commands to the BMC to signal channel initialisation, begin
357 - The control data is only written during initialisation. The control area is
374 drive the status register. Each side's initialisation sequence is outlined
385 #### BMC Initialisation Sequence
392 #### Host Initialisation Sequence
|
| /openbmc/u-boot/board/coreboot/coreboot/ |
| H A D | start.S | 11 /* No 32-bit board specific initialisation */
|
| /openbmc/u-boot/board/intel/edison/ |
| H A D | start.S | 11 /* No 32-bit board specific initialisation */
|
| /openbmc/linux/arch/parisc/include/asm/ |
| H A D | parport.h | 4 * parport.h: ia32-compatible parport initialisation
|
| /openbmc/u-boot/arch/arm/include/asm/arch-sunxi/ |
| H A D | gtbus.h | 3 * GTBUS initialisation
|
| /openbmc/linux/Documentation/driver-api/usb/ |
| H A D | callbacks.rst | 83 genuine error occurred during initialisation which prevented a driver
90 initialisation that doesn't take too long is a good idea here.
|
| /openbmc/linux/arch/arc/plat-tb10x/ |
| H A D | tb10x.c | 3 * Abilis Systems TB10x platform initialisation
|
| /openbmc/u-boot/board/toradex/apalis-tk1/ |
| H A D | Kconfig | 29 bool "Apalis Evaluation Board PCIe Initialisation"
|