| /openbmc/witherspoon-pfault-analysis/org/open_power/Witherspoon/ |
| H A D | Fault.errors.yaml | 4 the power supply cabling and/or input power source.
|
| /openbmc/linux/Documentation/networking/device_drivers/fddi/ |
| H A D | defza.rst | 24 by providing means to reuse existing cabling.
|
| /openbmc/phosphor-power/org/open_power/Witherspoon/ |
| H A D | Fault.errors.yaml | 4 the power supply cabling and/or input power source.
|
| /openbmc/linux/drivers/net/ethernet/realtek/ |
| H A D | Kconfig | 73 are using low quality on long cabling. It is required for RealTek
|
| /openbmc/linux/drivers/net/arcnet/ |
| H A D | arcdevice.h | 22 * within one minute before printing a "cabling problem" warning. The
25 * After that, a "cabling restored" message will be printed on the next IRQ
|
| H A D | arcnet.c | 1050 arc_printk(D_NORMAL, dev, "reconfiguration detected: cabling restored?\n"); in arcnet_interrupt()
1074 arc_printk(D_NORMAL, dev, "many reconfigurations detected: cabling problem?\n"); in arcnet_interrupt()
1087 arc_printk(D_NORMAL, dev, "cabling restored?\n"); in arcnet_interrupt()
|
| /openbmc/linux/Documentation/scsi/ |
| H A D | BusLogic.rst | 279 list. The retail kit includes the bare board and manual as well as cabling and
304 are installed in systems with cabling or termination that is not sufficient
374 installed in systems with cabling or termination that is not sufficient for
|
| H A D | sym53c8xx_2.rst | 705 On the other hand, either bad cabling, broken devices, not conformant
|
| H A D | ncr53c8xx.rst | 1224 On the other hand, either bad cabling, broken devices, not conformant
|
| /openbmc/linux/drivers/scsi/ |
| H A D | qlogicfas408.h | 44 /* This needs to be set to 1 if your cabling is long or noisy */
|
| H A D | Kconfig | 1087 There is no safe option other than using good cabling, right
|
| H A D | 3w-xxxx.c | 1233 …printk(KERN_WARNING "3w-xxxx: scsi%d: Controller errors, card not responding, check all cabling.\n… in tw_reset_sequence()
|
| /openbmc/bmcweb/redfish-core/schema/dmtf/json-schema/ |
| H A D | NetworkPort.v1_4_3.json | 418 …c capabilities of the port, irrespective of transient conditions such as cabling, interface module…
506 …ties of an associated port, irrespective of transient conditions such as cabling, interface module…
|
| /openbmc/linux/Documentation/networking/ |
| H A D | arcnet-hardware.rst | 16 some cabling tips, and a listing of all jumper settings I can find. Please
43 true; see below under "Cabling."
82 Cabling ARCnet Networks
99 types of cabling: coax and twisted pair. The other ARCnet-type networks
101 cabling (Type1, Fiber, C1, C4, C5).
107 Cards for coax cabling are shipped in two different variants: for BUS and
131 And now to the cabling. What you can connect together:
214 A basically different cabling scheme is used with Twisted Pair cabling. Each
256 meters for RG-62 cabling; less for others. You can see that using passive
384 OFF Short flashes Cabling problems (broken cable or not
|
| H A D | arcnet.rst | 10 and cabling information if you're like many of us and didn't happen to get a
|
| /openbmc/linux/Documentation/admin-guide/media/ |
| H A D | faq.rst | 156 cabling. Yet, it could also be some hardware or driver issue.
|
| /openbmc/linux/Documentation/networking/device_drivers/ethernet/3com/ |
| H A D | 3c509.rst | 78 AUI and 10base2 network cabling is physically incapable of full-duplex
|
| /openbmc/linux/Documentation/driver-api/media/ |
| H A D | dtv-frontend.rst | 225 at the cabling.
|
| /openbmc/bmcweb/redfish-core/schema/dmtf/csdl/ |
| H A D | NetworkPort_v1.xml | 102 …c capabilities of the port, irrespective of transient conditions such as cabling, interface module…
161 …ties of an associated port, irrespective of transient conditions such as cabling, interface module…
|
| /openbmc/linux/arch/sparc/include/asm/ |
| H A D | floppy_64.h | 445 * the cabling used in Ultras.
|
| /openbmc/linux/Documentation/networking/device_drivers/ethernet/cirrus/ |
| H A D | cs89x0.rst | 407 * Select 'Network Test' to test the network connection and cabling.
|
| /openbmc/linux/drivers/net/phy/ |
| H A D | phy-core.c | 492 …phydev_warn(phydev, "Downshift occurred from negotiated speed %s to actual speed %s, check cabling… in phy_check_downshift()
|
| /openbmc/linux/drivers/comedi/drivers/ |
| H A D | usbduxsigma.c | 1550 "Communication to USBDUXSIGMA failed! Check firmware and cabling.\n"); in usbduxsigma_auto_attach()
|
| /openbmc/linux/drivers/net/ethernet/amd/ |
| H A D | nmclan_cs.c | 1257 /* LCAR usually results from bad cabling. */ in update_stats()
|
| /openbmc/linux/include/linux/ |
| H A D | usb.h | 938 * reconfigured, by re-cabling a tree of USB devices or by moving USB host
|