Lines Matching +full:y +full:- +full:offset
16 default y
20 while U-Boot is running, but once U-Boot exits it will not be
21 stored. U-Boot will therefore always start up with a default
31 - CONFIG_ENV_OFFSET:
32 - CONFIG_ENV_SIZE:
34 These two #defines specify the offset and size of the
41 - CONFIG_ENV_EEPROM_IS_ON_I2C
45 - CONFIG_I2C_ENV_EEPROM_BUS
58 default y if ARCH_BCM283X
59 default y if ARCH_SUNXI && MMC
60 default y if MMC_OMAP_HS && TI_COMMON_CMD_OPTIONS
76 default y if ARCH_CINTEGRATOR
77 default y if ARCH_INTEGRATOR_CP
78 default y if M548x || M547x || M5282 || MCF547x_8x
79 default y if MCF532x || MCF52x2
80 default y if MPC86xx || MPC83xx
81 default y if ARCH_MPC8572 || ARCH_MPC8548 || ARCH_MPC8641
82 default y if SH && !CPU_SH4
88 "embedded" in the text segment with the U-Boot code. This
94 4 kB sectors - with U-Boot code before and after it. With
97 between U-Boot and the environment.
101 Offset of environment data (variable area) to the
103 type flash chips the second sector can be used: the offset
131 when your environment is "embedded" within U-Boot code,
133 for U-Boot code. It should be pointed out that this is
149 source code will make it necessary to adapt <board>/u-boot.lds*
156 default y if ARCH_EXYNOS4
157 default y if MX6SX || MX7D
158 default y if TEGRA30 || TEGRA124
159 default y if TEGRA_ARMV8_COMMON
177 These two #defines specify the offset and size of the environment
180 If offset is positive (the usual case), it is treated as relative to
181 the start of the MMC partition. If offset is negative, it is treated
217 - CONFIG_ENV_OFFSET:
218 - CONFIG_ENV_SIZE:
220 These two #defines specify the offset and size of the environment
224 - CONFIG_ENV_OFFSET_REDUND (optional):
232 - CONFIG_ENV_RANGE (optional):
240 - CONFIG_ENV_OFFSET_OOB (optional):
242 Enables support for dynamically retrieving the offset of the
243 environment from block zero's out-of-band data. The
244 "nand env.oob" command can be used to record this offset.
249 bool "Environment in a non-volatile RAM"
252 Define this if you have some non-volatile memory device
256 - CONFIG_ENV_ADDR:
257 - CONFIG_ENV_SIZE:
271 - CONFIG_ENV_ADDR:
272 - CONFIG_ENV_SIZE:
286 - CONFIG_ENV_ADDR:
287 - CONFIG_ENV_SIZE:
297 default y if ARMADA_XP
298 default y if INTEL_BAYTRAIL
299 default y if INTEL_BRASWELL
300 default y if INTEL_BROADWELL
301 default y if NORTHBRIDGE_INTEL_IVYBRIDGE
302 default y if INTEL_QUARK
303 default y if INTEL_QUEENSBAY
308 - CONFIG_ENV_OFFSET:
309 - CONFIG_ENV_SIZE:
311 These two #defines specify the offset and size of the
315 - CONFIG_ENV_SECT_SIZE:
319 - CONFIG_ENV_OFFSET_REDUND (optional):
384 environment. This has the benefit of wear-leveling the environment
387 - CONFIG_ENV_UBI_PART:
391 - CONFIG_ENV_UBI_VOLUME:
396 - CONFIG_ENV_UBI_VOLUME_REDUND:
415 default "0:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA = -1
416 default "1:auto" if ARCH_SUNXI && MMC_SUNXI_SLOT_EXTRA != -1
423 - "D:P": device D partition P. Error occurs if device D has no
425 - "D:0": device D.
426 - "D" or "D:": device D partition 1 if device D has partition
429 - "D:auto": first partition in device D with bootable flag set.
455 - "D:P": device D partition P. Error occurs if device D has no
457 - "D:0": device D.
458 - "D" or "D:": device D partition 1 if device D has partition
461 - "D:auto": first partition in device D with bootable flag set.
476 hex "Environment Offset"
485 Offset from the start of the device (or partition)
497 hex "Environment Sector-Size"
537 bool "Add run-time information to the environment"
540 run-time determined information about the hardware to the
546 default y if ENV_IS_NOWHERE
554 default y
562 default y
570 default y
578 default y
586 default y
594 default y
604 default y if ENV_IS_NOWHERE
612 default y
620 default y
628 default y
636 default y
644 default y
652 default y
659 hex "Environment offset"
663 Offset from the start of the device (or partition)