arm/dts/sun7i-a20-pcduino3.dts

5  * This file is dual-licensed: you can use it either under the terms
44 /dts-v1/;
45 #include "sun7i-a20.dtsi"
46 #include "sunxi-common-regulators.dtsi"
48 #include <dt-bindings/gpio/gpio.h>
49 #include <dt-bindings/input/input.h>
50 #include <dt-bindings/interrupt-controller/irq.h>
54 	compatible = "linksprite,pcduino3", "allwinner,sun7i-a20";
61 		stdout-path = "serial0:115200n8";
65 		compatible = "gpio-leds";
66 		pinctrl-names = "default";
67 		pinctrl-0 = <&led_pins_pcduino3>;
71 			gpios = <&pio 7 15 GPIO_ACTIVE_LOW>;
74 		rx {
75 			label = "pcduino3:green:rx";
76 			gpios = <&pio 7 16 GPIO_ACTIVE_LOW>;
81 		compatible = "gpio-keys";
82 		pinctrl-names = "default";
83 		pinctrl-0 = <&key_pins_pcduino3>;
84 		#address-cells = <1>;
85 		#size-cells = <0>;
89 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
94 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
99 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
105 	target-supply = <&reg_ahci_5v>;
114 	cpu-supply = <&reg_dcdc2>;
126 	pinctrl-names = "default";
127 	pinctrl-0 = <&gmac_pins_mii_a>;
129 	phy-mode = "mii";
132 	phy1: ethernet-phy@1 {
138 	pinctrl-names = "default";
139 	pinctrl-0 = <&i2c0_pins_a>;
144 		interrupt-parent = <&nmi_intc>;
152 	pinctrl-names = "default";
153 	pinctrl-0 = <&ir0_rx_pins_a>;
158 	pinctrl-names = "default";
159 	pinctrl-0 = <&mmc0_pins_a>;
160 	vmmc-supply = <&reg_vcc3v3>;
161 	bus-width = <4>;
162 	cd-gpios = <&pio 7 1 GPIO_ACTIVE_LOW>; /* PH1 */
192 		bias-pull-up;
202 	regulator-always-on;
203 	regulator-min-microvolt = <1000000>;
204 	regulator-max-microvolt = <1400000>;
205 	regulator-name = "vdd-cpu";
209 	regulator-always-on;
210 	regulator-min-microvolt = <1000000>;
211 	regulator-max-microvolt = <1400000>;
212 	regulator-name = "vdd-int-pll";
216 	regulator-name = "vdd-rtc";
220 	regulator-always-on;
221 	regulator-min-microvolt = <3000000>;
222 	regulator-max-microvolt = <3000000>;
223 	regulator-name = "avcc";
235 	pinctrl-names = "default";
236 	pinctrl-0 = <&uart0_pins_a>;
246 	pinctrl-names = "default";
247 	pinctrl-0 = <&usb0_id_detect_pin>;
248 	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
249 	usb1_vbus-supply = <&reg_usb1_vbus>;
250 	usb2_vbus-supply = <&reg_usb2_vbus>;