Lines Matching +full:pwm +full:- +full:leds
1 # SPDX-License-Identifier: GPL-2.0-only
13 LEDs from both userspace and optionally, by kernel events (triggers).
20 This option enables the LED sysfs class in /sys/class/leds. You'll
21 need this to do anything useful with LEDs. If unsure, say Y.
27 This option enables the flash LED sysfs class in /sys/class/leds.
28 It wraps LED Class and adds flash LEDs specific sysfs attributes
37 This option enables the multicolor LED sysfs class in /sys/class/leds.
40 for multicolor LEDs that are grouped together. This class is not
41 intended for single color LEDs. It can be built as a module.
48 for LED sysfs class devices under /sys/class/leds.
50 See Documentation/ABI/testing/sysfs-class-led for details.
59 This option enables support for on-chip LED drivers found on Marvell
66 This option enables support for the AN30259A 3-channel
70 will be called leds-an30259a.
77 This driver makes the PC Engines APU1 front panel LEDs
80 If you're looking for APU2/3, use the pcengines-apu2 driver.
84 module will be called leds-apu.
92 LEDs on Dell Wyse 3020 (Ariel) board via the KB3930 Embedded
104 an I2C interface, up to 36/54/72 LEDs or 12/18/24 RGBs,
108 will be called leds-aw200xx.
115 This option enables support for the AW2013 3-channel
119 will be called leds-aw2013.
127 This option enables support for LEDs connected to the BCM6328
136 This option enables support for LEDs connected to the BCM6358
144 This option enables support for charger and general purpose LEDs
148 will be called leds-cht-wcove.
156 This option enables support for LEDs offered by Motorola's
170 will be called leds-cr0014114.
183 will be called leds-el15203000.
192 This option enables basic support for the LEDs found on the front
193 side of CZ.NIC's Turris Omnia router. There are 12 RGB LEDs on the
203 controlled manually or using PWM input or using ambient
214 controlled manually or using PWM input or using ambient
222 This option enables support for the LEDs on National Semiconductor /
225 The LEDs can be controlled directly, through PWM input, or by the
226 ambient-light-sensor interface. The chip supports
227 hardware-accelerated blinking with maximum on and off periods of 9.8
235 This option enables support for LEDs connected to LM3642.
236 The LM3642 is a 4MHz fixed-frequency synchronous boost
237 converter plus 1.5A constant current driver for a high-current
253 This option enables support for the LEDs on Sharp Locomo.
254 Zaurus models SL-5500 and SL-5600.
269 This option enables support for on-chip LED drivers found on
281 tristate "LED Support for the WRAP series LEDs"
285 This option enables support for the PCEngines WRAP programmable LEDs.
299 This option enables support for the Cobalt Raq series LEDs.
308 LEDs on the I/O and CPU boards of SunFire UltraSPARC servers.
346 tristate "LED Support for GPIO connected LEDs"
350 This option enables support for the LEDs connected to GPIO
351 outputs. To be useful the particular board must have LEDs
352 and they must be connected to the GPIO lines. The LEDs must be
361 This option enables support for LEDs connected to the National
366 module will be called leds-lp3944.
375 This option enables support for LEDs connected to the Texas
379 module will be called leds-lp3952.
390 module will be called leds-lp50xx.
452 This option enables support for the Keyboard LEDs on the LP8788 PMIC.
461 This option enables support for the display cluster LEDs
471 programs through the LEDs subsystem. This LED has three
474 The driver supports two kinds of interface: using ledtrig-timer
475 or through /sys/class/leds/clevo::mail/brightness. As this LED
494 module will be called leds-clevo-mail.
501 This option enables support for LEDs connected to PCA955x
521 This option enables support for LEDs connected to the PCA963x
530 This option enables support for LEDs connected to PCA995x
535 tristate "LED support for status LEDs on WM831x PMICs"
539 This option enables support for the status LEDs of the WM831x
547 This option enables support for LEDs driven by the Wolfson
555 This option enables support for on-chip LED drivers found
559 tristate "Dialog DA9052/DA9053 LEDS"
563 This option enables support for on-chip LED drivers found
564 on Dialog Semiconductor DA9052-BC and DA9053-AA/Bx PMICs.
572 which can be used to control up to four LEDs.
575 tristate "PWM driven LED Support"
577 depends on PWM
579 This option enables support for pwm driven LEDs
586 This option enables support for regulator driven LEDs.
600 be called leds-bd2606mvv.
618 drive or power LEDs on the front panel. Using this driver
626 This option enables support for LEDs driven by a Linear Technology
627 LT3593 controller. This controller uses a special one-wire pulse
635 This option enables support for on-chip LED drivers found
639 be called leds-adp5520.
646 This option enables support for on-chip LED drivers found
650 tristate "LED support for Network Space v2 GPIO LEDs"
655 This option enables support for the dual-GPIO LEDs found on the
661 n090401 (Seagate NAS 4-Bay)
664 tristate "LED support for Big Network series LEDs"
670 This option enables support for LEDs found on the LaCie 2Big
671 and 5Big Network v2 boards. The LEDs are wired to a CPLD and are
678 This option enables support for LEDs connected to TC6507
680 Driver support brightness control and hardware-assisted blinking.
694 LEDs driver for MAX77650 family of PMICs from Maxim Integrated.
700 This option enables support for on-chip LED drivers on
708 This option enables support for LEDs connected to LM3554
715 This option enables support for the LEDs on the Bachmann OT200.
716 Say Y to enable LEDs on the Bachmann OT200.
722 Say Y here to include support for the MEN 14F021P00 BMC LEDs.
725 will be called leds-menf21bmc.
732 This option enables support for LEDs connected to ISSI IS31FL319x
734 Driver supports individual PWM brightness control for each channel.
737 called leds-is31fl319x.
743 Say Y here to include support for ISSI IS31FL32XX and Si-En SN32xx
744 LED controllers. They are I2C devices with multiple constant-current
745 channels, each with independent 256-level PWM control.
753 LEDs.
756 called leds-sc27xx-bltc.
774 This option enables support for the system LEDs present on
777 will be called leds-powernv.
780 bool "LED support for LEDs on system controllers"
785 This option enables support for the LEDs on syscon type
802 This option enables support for the LEDs on the Mellanox
809 This option enables support for the LEDs on the Mellanox Ethernet and
812 module, choose 'M' here: the module will be called leds-mlxreg.
818 This option enables support for userspace LEDs. Say 'y' to enable this
827 This option enables support for the User1 and User2 LEDs on NI
831 will be called leds-nic78bx.
874 It is a single boost converter primarily for white LEDs and
882 This option enables support for the Red and White LEDs of
886 will be called leds-ip30.
895 source "drivers/leds/blink/Kconfig"
898 source "drivers/leds/flash/Kconfig"
901 source "drivers/leds/rgb/Kconfig"
904 source "drivers/leds/trigger/Kconfig"
907 source "drivers/leds/simple/Kconfig"