Lines Matching +full:charging +full:- +full:current
5 Contact: linux-pm@vger.kernel.org
14 Contact: linux-pm@vger.kernel.org
23 Contact: linux-pm@vger.kernel.org
32 Contact: linux-pm@vger.kernel.org
43 Contact: linux-pm@vger.kernel.org
47 Reports an average IBAT current reading for the battery, over
54 Reports an average IBUS current reading over a fixed period.
61 used for discharging batteries, positive values for charging
62 batteries and for USB IBUS current.
66 Contact: linux-pm@vger.kernel.org
70 Reports the maximum IBAT current allowed into the battery.
74 Reports the maximum IBUS current the supply can support.
81 Contact: linux-pm@vger.kernel.org
86 Reports an instant, single IBAT current reading for the
93 Reports the IBUS current supplied now. This value is generally
94 read-only reporting, unless the 'online' state of the supply
101 used for discharging batteries, positive values for charging
102 batteries and for USB IBUS current.
106 Contact: linux-pm@vger.kernel.org
110 Reports the current TBAT battery temperature reading.
114 Reports the current supply temperature reading. This would
124 Contact: linux-pm@vger.kernel.org
128 Maximum TBAT temperature trip-wire value where the supply will
129 notify user-space of the event.
133 Maximum supply temperature trip-wire value where the supply
134 will notify user-space of the event.
136 This is normally used for the charging scenario where
137 user-space needs to know if the temperature has crossed an
139 user that the temperature is critically high, and charging has
148 Contact: linux-pm@vger.kernel.org
153 Minimum TBAT temperature trip-wire value where the supply will
154 notify user-space of the event.
158 Minimum supply temperature trip-wire value where the supply
159 will notify user-space of the event.
161 This is normally used for the charging scenario where user-space
164 temperature level is high, and charging current has been
173 Contact: linux-pm@vger.kernel.org
178 charging.
190 Contact: linux-pm@vger.kernel.org
195 charging.
207 Contact: linux-pm@vger.kernel.org
212 battery, during charging.
224 Contact: linux-pm@vger.kernel.org
241 Contact: linux-pm@vger.kernel.org
253 read-only reporting, unless the 'online' state of the supply
265 Contact: linux-pm@vger.kernel.org
271 Valid values: 0 - 100 (percent)
275 Contact: linux-pm@vger.kernel.org
277 Maximum battery capacity trip-wire value where the supply will
278 notify user-space of the event. This is normally used for the
279 battery discharging scenario where user-space needs to know the
286 Valid values: 0 - 100 (percent)
290 Contact: linux-pm@vger.kernel.org
292 Minimum battery capacity trip-wire value where the supply will
293 notify user-space of the event. This is normally used for the
294 battery discharging scenario where user-space needs to know the
301 Valid values: 0 - 100 (percent)
305 Contact: linux-pm@vger.kernel.org
310 Values close to 0% will be returned after (re-)calibration
317 Valid values: 0 - 100 (percent)
321 Contact: linux-pm@vger.kernel.org
333 Contact: linux-pm@vger.kernel.org
335 Maximum allowable charging current. Used for charge rate
344 Contact: linux-pm@vger.kernel.org
354 Contact: linux-pm@vger.kernel.org
356 Represents a battery percentage level, below which charging will
360 Valid values: 0 - 100 (percent)
364 Contact: linux-pm@vger.kernel.org
366 Represents a battery percentage level, above which charging will
374 Valid values: 0 - 100 (percent)
378 Contact: linux-pm@vger.kernel.org
380 Represents the type of charging currently being applied to the
382 charging speeds. "Adaptive" means that the charger uses some
387 charging rate in order to prolong the battery health. "Bypass"
388 means the charger bypasses the charging path around the
400 Contact: linux-pm@vger.kernel.org
402 Reports the charging current value which is used to determine
403 when the battery is considered full and charging should end.
411 Contact: linux-pm@vger.kernel.org
422 "Over current", "Calibration required", "Warm",
427 Contact: linux-pm@vger.kernel.org
429 Reports the charging current applied during pre-charging phase
438 Contact: linux-pm@vger.kernel.org
454 Contact: linux-pm@vger.kernel.org
456 Represents the charging status of the battery. Normally this
457 is read-only reporting although for some supplies this can be
458 used to enable/disable charging to the battery.
463 "Unknown", "Charging", "Discharging",
464 "Not charging", "Full"
468 Contact: linux-pm@vger.kernel.org
470 Represents the charging behaviour.
477 inhibit-charge: Do not charge while AC is attached
478 force-discharge: Force discharge while AC is attached
483 Contact: linux-pm@vger.kernel.org
490 "Unknown", "NiMH", "Li-ion", "Li-poly", "LiFe",
496 Contact: linux-pm@vger.kernel.org
508 Contact: linux-pm@vger.kernel.org
523 Contact: linux-pm@vger.kernel.org
525 Details the incoming IBUS current limit currently set in the
528 of 500mA so the input current limit is set to the same value).
538 Contact: linux-pm@vger.kernel.org
542 system-level knowledge or user input (e.g. This is part of the
556 Contact: linux-pm@vger.kernel.org
560 system-level knowledge or user input. Use preferably this
561 feature to limit the incoming power and use current/voltage
570 Contact: linux-pm@vger.kernel.org
574 between online states (e.g. Fixed -> Programmable for a PD_PPS
575 USB supply so voltage and current can be controlled).
583 1: Online Fixed - Fixed Voltage Supply
584 2: Online Programmable - Programmable Voltage Supply
589 Contact: linux-pm@vger.kernel.org
592 the supply, for example it can show if USB-PD capable source
595 Access: Read-Only
603 What: /sys/class/power/ds2760-battery.*/charge_now
608 This file is writeable and can be used to set the current
611 A userspace daemon can monitor the battery charging logic
615 What: /sys/class/power/ds2760-battery.*/charge_full
624 What: /sys/class/power_supply/max14577-charger/device/fast_charge_timer
630 charger operates in fast-charge mode. When the timer expires
631 the device will terminate fast-charge mode (charging current
636 - 5, 6 or 7 (hours),
637 - 0: disabled.
639 What: /sys/class/power_supply/max77693-charger/device/fast_charge_timer
645 charger operates in fast-charge mode. When the timer expires
646 the device will terminate fast-charge mode (charging current
651 - 4 - 16 (hours), step by 2 (rounded down)
652 - 0: disabled.
654 What: /sys/class/power_supply/max77693-charger/device/top_off_threshold_current
659 This entry shows and sets the charging current threshold for
660 entering top-off charging mode. When charging current in fast
662 interrupt and start top-off charging mode.
666 - 100000 - 200000 (microamps), step by 25000 (rounded down)
667 - 200000 - 350000 (microamps), step by 50000 (rounded down)
668 - 0: disabled.
670 What: /sys/class/power_supply/max77693-charger/device/top_off_timer
676 charger operates in top-off charge mode. When the timer expires
677 the device will terminate top-off charge mode (charging current
682 - 0 - 70 (minutes), step by 10 (rounded down)
684 What: /sys/class/power_supply/bq24257-charger/ovp_voltage
689 This entry configures the overvoltage protection feature of bq24257-
696 - 6000000, 6500000, 7000000, 8000000, 9000000, 9500000, 10000000,
699 What: /sys/class/power_supply/bq24257-charger/in_dpm_voltage
705 bq24257-type charger devices. Once the supply drops to the configured
706 voltage, the input current limit is reduced down to prevent the further
707 drop of the supply. When the IC enters this mode, the charge current is
712 - 4200000, 4280000, 4360000, 4440000, 4520000, 4600000, 4680000,
715 What: /sys/class/power_supply/bq24257-charger/high_impedance_enable
720 This entry allows enabling the high-impedance mode of bq24257-type
727 - 1: enabled
728 - 0: disabled
730 What: /sys/class/power_supply/bq24257-charger/sysoff_enable
735 This entry allows enabling the sysoff mode of bq24257-type charger
743 - 1: enabled
744 - 0: disabled
748 Contact: linux-pm@vger.kernel.org
759 Contact: linux-pm@vger.kernel.org
765 Valid values: 1-12
769 Contact: linux-pm@vger.kernel.org
774 Valid values: 1-31