arm: mvebu: Make ECC support configurable on Armada XP

Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boar

arm: mvebu: Make ECC support configurable on Armada XP

Currently, ECC support is enabled for all Armada XP boards. So the
DDR3 driver tries to configure the controller with ECC support, even
on boards without ECC. This patch makes this ECC optional which now
can be configured on a board-per-board basis.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Phil Sutter <phil@nwl.cc>

show more ...

arm: mvebu: Move some defines to common include file

This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.

Signed-off-b

arm: mvebu: Move some defines to common include file

This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>

show more ...

net: mvneta: Convert to driver model

Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed complet

net: mvneta: Convert to driver model

Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.

With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:

PHY-mode ("phy-mode") and PHY-address ("reg").

The base addresses for the ethernet controllers can be removed from
the header files as well.

Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>

show more ...

arm: mvebu: Add DM and OF_CONTROL support to SPL

This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.

This patch also adds the necessa

arm: mvebu: Add DM and OF_CONTROL support to SPL

This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.

This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.

Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:

arch/arm/cpu/u-boot-spl.lds

This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>

show more ...

sf: Move SPI flash drivers to defconfig

There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signe

sf: Move SPI flash drivers to defconfig

There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported

arm, powerpc: select SYS_GENERIC_BOARD

We have finished Generic Board conversion for ARM and PowerPC, i.e.
all the boards have been converted except OpenRISC, SuperH, SPARC,
which have not supported Generic Board framework yet.

Select SYS_GENERIC_BOARD in arch/Kconfig and delete all the macro
defines in include/configs/*.h.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPL

When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowle

arm: mvebu: Only set CONFIG_SKIP_LOWLEVEL_INIT for SPL

When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Move CONFIG_SYS_TEXT_BASE to an address < 16 MiB

This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
th

arm: mvebu: Move CONFIG_SYS_TEXT_BASE to an address < 16 MiB

This patch moves CONFIG_SYS_TEXT_BASE to 0x00800000 for all Armada
XP / 38x boards in mainline U-Boot. This is done in preparation for
the ECC SDRAM scrubbing that needs to be done in the main U-Boot.
The SPL (previously bin_hdr) has already scrubbed the area:
0x0000.0000 - 0x0100.0000

In this area this main U-Boot needs to get loaded. The main U-Boot
then can scrub the remaining SDRAM area while running from this
location.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>

show more ...

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: drivers/ddr: Move Armada XP DDR init code into new directory

With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to

arm: mvebu: drivers/ddr: Move Armada XP DDR init code into new directory

With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.

This will be the new structure:

drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)

drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)

Signed-off-by: Stefan Roese <sr@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-spi

defconfig: Move CONFIG_SPI_FLASH_BAR from configs

This commit moves:
- CONFIG_SPI_FLASH_BAR

from include/configs/*.h into configs/*_defconfigs

Signed-off-by: Jagan Teki <jteki@openedev.com>

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Move defaults from config_cmd_default.h to Kconfig

This sets the default commands Kconfig to match
include/config_cmd_default.h commands in the common/Kconfig and removes
them from include/configs.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-marvell

arm: mvebu: Change network init code to allow a more flexible setup

With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times

arm: mvebu: Change network init code to allow a more flexible setup

With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.

Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

arm: mvebu: Move CONFIG_SPL_LDSCRIPT to common header

This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.

Signed-off-by: Stefan Roese <sr@denx.de>
Teste

arm: mvebu: Move CONFIG_SPL_LDSCRIPT to common header

This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>

show more ...

arm: mvebu: Move mvebu-common into mach-mvebu

Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.

Signed-off-by: Stefan

arm: mvebu: Move mvebu-common into mach-mvebu

Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>

show more ...

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'master' of http://git.denx.de/u-boot-sunxi