Merge branch '5.12/scsi-fixes' into 5.13/scsi-staging

Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.

Merge branch '5.12/scsi-fixes' into 5.13/scsi-staging

Pull 5.12/scsi-fixes into the 5.13 SCSI tree to provide a baseline for
some UFS changes that would otherwise cause conflicts during the
merge.

Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

show more ...

Merge 5.12-rc6 into tty-next

We need the serial/tty fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.12-rc6 into char-misc-next

We need the char/misc fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge series "Support ROHM BD71815 PMIC" from Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>:

Patch series introducing support for ROHM BD71815 PMIC

ROHM BD71815 is a power management IC used

Merge series "Support ROHM BD71815 PMIC" from Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>:

Patch series introducing support for ROHM BD71815 PMIC

ROHM BD71815 is a power management IC used in some battery powered
systems. It contains regulators, GPO(s), charger + coulomb counter, RTC
and a clock gate.

All regulators can be controlled via I2C. LDO4 can additionally be set to
be enabled/disabled by a GPIO. LDO3 voltage could be selected from two
voltages written into separate VSEL reisters using GPIO but this mode is
not supported by driver. On top of that the PMIC has the typical HW
state machine which is present also on many other ROHM PMICs.

IC contains two GPOs - but one of the GPOs is marked as GND in
data-sheet. Thus the driver by default only exposes one GPO. The second
GPO can be enabled by special DT property.

RTC is almost similar to what is on BD71828. For currently used features
only the register address offset to RTC block differs.

The charger driver is not included in this series. ROHM has a charger
driver with some fuel-gauging logig written in but this is not included
here. I am working on separating the logic from HW specific driver and
supporting both BD71815 and BD71828 chargers in separate patch series.

Changelog v5:
Regulator:
- Added regmap helper for regulator ramp-delay and taken it in use
(patches 13, 14, 16 - they can be just dropped if ramp-delay helper is not
a good idea. Patch 15 implements old-fashioned ramp-delay)
GPIO:
- styling changes to GPIO (Mostly suggested by Andy)
- implemented init_valid_mask (but can't count on it yet)
Changelog v4:
- Sorted ROHM chip ID enum
- Statcized DVS structures in regulator driver
- Minor styling for regulator driver
- rebased on v5.12-rc4
Changelog v3:
- GPIO clean-up as suggested by Bartosz
- MFD clean-up as suggested by Lee
- clk-mode dt-binding handling in MFD driver corrected to reflect new
property values.
- Dropped already applied patches
- Rebased on v5.12-rc2
Changelog v2:
- Rebased on top of v5.11-rc3
- Added another "preliminary patch" which fixes HW-dvs voltage
handling (patch 1)
- split regulator patch to two.
- changed dt-binding patch ordering.
regulators:
- staticized probe
- removed some unnecessary defines
- updated comments
- split rohm-regulator patch adding SNVS and supporting simple
linear mapping into two - one adding support for mapping, other
adding SNVS.
GPIO:
- removed unnecessary headers
- clarified dev/parent->dev usage
- removed forgotten #define DEBUG
dt-bindings:
- changed patch order to meet ref-dependencies
- added missing regulator nodes
- changed string property for clk mode to tristated
MFD:
- header cleanups.
CLK:
- fixed commit message

--

Matti Vaittinen (19):
rtc: bd70528: Do not require parent data
mfd: bd718x7: simplify by cleaning unnecessary device data
dt_bindings: bd71828: Add clock output mode
dt_bindings: regulator: Add ROHM BD71815 PMIC regulators
dt_bindings: mfd: Add ROHM BD71815 PMIC
mfd: Add ROHM BD71815 ID
mfd: Sort ROHM chip ID list for better readability
mfd: Support for ROHM BD71815 PMIC core
gpio: support ROHM BD71815 GPOs
regulator: helpers: Export helper voltage listing
regulator: rohm-regulator: linear voltage support
regulator: rohm-regulator: Support SNVS HW state.
regulator: Add regmap helper for ramp-delay setting
regulator: bd718x7, bd71828: Use ramp-delay helper
regulator: Support ROHM BD71815 regulators
regulator: bd71815: use ramp-delay helper
clk: bd718x7: Add support for clk gate on ROHM BD71815 PMIC
rtc: bd70528: Support RTC on ROHM BD71815
MAINTAINERS: Add ROHM BD71815AGW

.../bindings/mfd/rohm,bd71815-pmic.yaml | 201 ++++++
.../bindings/mfd/rohm,bd71828-pmic.yaml | 6 +
.../regulator/rohm,bd71815-regulator.yaml | 116 ++++
MAINTAINERS | 3 +
drivers/clk/clk-bd718x7.c | 9 +-
drivers/gpio/Kconfig | 10 +
drivers/gpio/Makefile | 1 +
drivers/gpio/gpio-bd71815.c | 193 ++++++
drivers/mfd/Kconfig | 15 +-
drivers/mfd/rohm-bd71828.c | 486 +++++++++----
drivers/mfd/rohm-bd718x7.c | 43 +-
drivers/regulator/Kconfig | 11 +
drivers/regulator/Makefile | 1 +
drivers/regulator/bd71815-regulator.c | 651 ++++++++++++++++++
drivers/regulator/bd71828-regulator.c | 51 +-
drivers/regulator/bd718x7-regulator.c | 60 +-
drivers/regulator/helpers.c | 101 ++-
drivers/regulator/rohm-regulator.c | 23 +-
drivers/rtc/Kconfig | 6 +-
drivers/rtc/rtc-bd70528.c | 104 +--
include/linux/mfd/rohm-bd71815.h | 562 +++++++++++++++
include/linux/mfd/rohm-bd71828.h | 3 +
include/linux/mfd/rohm-bd718x7.h | 13 -
include/linux/mfd/rohm-generic.h | 15 +-
include/linux/regulator/driver.h | 7 +
25 files changed, 2393 insertions(+), 298 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml
create mode 100644 Documentation/devicetree/bindings/regulator/rohm,bd71815-regulator.yaml
create mode 100644 drivers/gpio/gpio-bd71815.c
create mode 100644 drivers/regulator/bd71815-regulator.c
create mode 100644 include/linux/mfd/rohm-bd71815.h

base-commit: 0d02ec6b3136c73c09e7859f0d0e4e2c4c07b49b
--
2.25.4

--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND

~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]

show more ...

Merge tag 'v5.12-rc5' into WIP.x86/core, to pick up recent NOP related changes

In particular we want to have this upstream commit:

b90829704780: ("bpf: Use NOP_ATOMIC5 instead of emit_nops(&prog,

Merge tag 'v5.12-rc5' into WIP.x86/core, to pick up recent NOP related changes

In particular we want to have this upstream commit:

b90829704780: ("bpf: Use NOP_ATOMIC5 instead of emit_nops(&prog, 5) for BPF_TRAMP_F_CALL_ORIG")

... before merging in x86/cpu changes and the removal of the NOP optimizations, and
applying PeterZ's !retpoline objtool series.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

Merge tag 'mute-led-rework' of https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-5.13

ALSA: control - add generic LED API

This patchset tries to resolve the diversity in the aud

Merge tag 'mute-led-rework' of https://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into asoc-5.13

ALSA: control - add generic LED API

This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.

A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).

The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.

The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).

snd_ctl_led 24576 0

The sound driver implementation is really easy:

1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED

Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>

show more ...

Merge tag 'tags/mute-led-rework' into for-next

ALSA: control - add generic LED API

This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer

Merge tag 'tags/mute-led-rework' into for-next

ALSA: control - add generic LED API

This patchset tries to resolve the diversity in the audio LED
control among the ALSA drivers. A new control layer registration
is introduced which allows to run additional operations on
top of the elementary ALSA sound controls.

A new control access group (three bits in the access flags)
was introduced to carry the LED group information for
the sound controls. The low-level sound drivers can just
mark those controls using this access group. This information
is not exported to the user space, but user space can
manage the LED sound control associations through sysfs
(last patch) per Mark's request. It makes things fully
configurable in the kernel and user space (UCM).

The actual state ('route') evaluation is really easy
(the minimal value check for all channels / controls / cards).
If there's more complicated logic for a given hardware,
the card driver may eventually export a new read-only
sound control for the LED group and do the logic itself.

The new LED trigger control code is completely separated
and possibly optional (there's no symbol dependency).
The full code separation allows eventually to move this
LED trigger control to the user space in future.
Actually it replaces the already present functionality
in the kernel space (HDA drivers) and allows a quick adoption
for the recent hardware (ASoC codecs including SoundWire).

snd_ctl_led 24576 0

The sound driver implementation is really easy:

1) call snd_ctl_led_request() when control LED layer should be
automatically activated
/ it calls module_request("snd-ctl-led") on demand /
2) mark all related kcontrols with
SNDRV_CTL_ELEM_ACCESS_SPK_LED or
SNDRV_CTL_ELEM_ACCESS_MIC_LED

Link: https://lore.kernel.org/r/20210317172945.842280-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>

show more ...

Merge tag 'platform-drivers-x86-surface-aggregator-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into for-5.13/surface-system-aggregator-intergration

Pull immu

Merge tag 'platform-drivers-x86-surface-aggregator-v5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into for-5.13/surface-system-aggregator-intergration

Pull immutable integration branch from Hans de Goede to have a stable base for
SSAM (Surface System Aggregator Module) HID transport subsystem merge.

=====
Signed tag for the immutable platform-surface-aggregator-registry
branch for merging into other sub-systems.

Note this is based on v5.12-rc2.
=====

show more ...

Merge tag 'v5.12-rc5' into locking/core, to pick up fixes

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up fixes sent via perf/urgent and in the BPF tools/ directories.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'v5.12-rc4' into next

Sync up with the mainline to bring in newest APIs.

Merge 5.12-rc4 into usb-next

We need the usb/thunderbolt fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge v5.12-rc4 into staging-next

We want the staging/iio fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge branch 'linus' into x86/cleanups, to resolve conflict

Conflicts:
arch/x86/kernel/kprobes/ftrace.c

Signed-off-by: Ingo Molnar <mingo@kernel.org>

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Eight fixes, all in drivers, all fairly minor either being fixes in
error

Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi

Pull SCSI fixes from James Bottomley:
"Eight fixes, all in drivers, all fairly minor either being fixes in
error legs, memory leaks on teardown, context errors or semantic
problems"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mpt3sas: Do not use GFP_KERNEL in atomic context
scsi: ufs: ufs-mediatek: Correct operator & -> &&
scsi: sd_zbc: Update write pointer offset cache
scsi: lpfc: Fix some error codes in debugfs
scsi: qla2xxx: Fix broken #endif placement
scsi: st: Fix a use after free in st_open()
scsi: myrs: Fix a double free in myrs_cleanup()
scsi: ibmvfc: Free channel_setup_buf during device tear down

show more ...

scsi: mpt3sas: Fix a few kernel-doc issues

Fixes the following W=1 kernel build warning(s):

drivers/scsi/mpt3sas/mpt3sas_scsih.c:763: warning: Function parameter or member 'sas_address' not descri

scsi: mpt3sas: Fix a few kernel-doc issues

Fixes the following W=1 kernel build warning(s):

drivers/scsi/mpt3sas/mpt3sas_scsih.c:763: warning: Function parameter or member 'sas_address' not described in '__mpt3sas_get_sdev_by_addr'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:763: warning: expecting prototype for mpt3sas_get_sdev_by_addr(). Prototype was for __mpt3sas_get_sdev_by_addr() instead
drivers/scsi/mpt3sas/mpt3sas_scsih.c:4535: warning: expecting prototype for _scsih_check_for_pending_internal_cmds(). Prototype was for mpt3sas_check_for_pending_internal_cmds() instead
drivers/scsi/mpt3sas/mpt3sas_scsih.c:6188: warning: Function parameter or member 'port_entry' not described in '_scsih_look_and_get_matched_port_entry'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:6188: warning: Function parameter or member 'matched_port_entry' not described in '_scsih_look_and_get_matched_port_entry'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:6188: warning: Function parameter or member 'count' not described in '_scsih_look_and_get_matched_port_entry'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:6959: warning: Function parameter or member 'port' not described in 'mpt3sas_expander_remove'
drivers/scsi/mpt3sas/mpt3sas_scsih.c:10494: warning: expecting prototype for mpt3sas_scsih_reset_handler(). Prototype was for mpt3sas_scsih_pre_reset_handler() instead
drivers/scsi/mpt3sas/mpt3sas_scsih.c:10536: warning: expecting prototype for mpt3sas_scsih_reset_handler(). Prototype was for mpt3sas_scsih_reset_done_handler() instead
drivers/scsi/mpt3sas/mpt3sas_scsih.c:12303: warning: expecting prototype for scsih__ncq_prio_supp(). Prototype was for scsih_ncq_prio_supp() instead

Link: https://lore.kernel.org/r/20210317091230.2912389-15-lee.jones@linaro.org
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: MPT-FusionLinux.pdl@avagotech.com
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

show more ...

scsi: mpt3sas: Do not use GFP_KERNEL in atomic context

mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.

Issue spotted by

scsi: mpt3sas: Do not use GFP_KERNEL in atomic context

mpt3sas_get_port_by_id() can be called when a spinlock is held. Use
GFP_ATOMIC instead of GFP_KERNEL when allocating memory.

Issue spotted by call_kern.cocci:
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7125 inside lock on line 7123 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6842 inside lock on line 6839 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 6854 inside lock on line 6851 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 7706 inside lock on line 7702 but uses GFP_KERNEL
./drivers/scsi/mpt3sas/mpt3sas_scsih.c:416:42-52: ERROR: function mpt3sas_get_port_by_id called on line 10260 inside lock on line 10256 but uses GFP_KERNEL

Link: https://lore.kernel.org/r/20210220093951.905362-1-christophe.jaillet@wanadoo.fr
Fixes: 324c122fc0a4 ("scsi: mpt3sas: Add module parameter multipath_on_hba")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

show more ...

Merge drm/drm-next into drm-misc-next

Noralf needs some patches in 5.12-rc3, and we've been delaying the 5.12
merge due to the swap issue so it looks like a good time.

Signed-off-by: Maxime Ripard

Merge drm/drm-next into drm-misc-next

Noralf needs some patches in 5.12-rc3, and we've been delaying the 5.12
merge due to the swap issue so it looks like a good time.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

show more ...

scsi: mpt3sas: Move a little data from the stack onto the heap

Fixes the following W=1 kernel build warning(s):

drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function ‘_scsih_scan_for_devices_after_res

scsi: mpt3sas: Move a little data from the stack onto the heap

Fixes the following W=1 kernel build warning(s):

drivers/scsi/mpt3sas/mpt3sas_scsih.c: In function ‘_scsih_scan_for_devices_after_reset’:
drivers/scsi/mpt3sas/mpt3sas_scsih.c:10473:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]

Link: https://lore.kernel.org/r/20210303144631.3175331-31-lee.jones@linaro.org
Cc: Sathya Prakash <sathya.prakash@broadcom.com>
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: MPT-FusionLinux.pdl@avagotech.com
Cc: MPT-FusionLinux.pdl@broadcom.com
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

show more ...

Merge tag 'irqchip-fixes-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes from Marc Zyngier:

- More compatible strings for the Ingenic

Merge tag 'irqchip-fixes-5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/urgent

Pull irqchip fixes from Marc Zyngier:

- More compatible strings for the Ingenic irqchip (introducing the
JZ4760B SoC)
- Select GENERIC_IRQ_MULTI_HANDLER on the ARM ep93xx platform
- Drop all GENERIC_IRQ_MULTI_HANDLER selections from the irqchip
Kconfig, now relying on the architecture to get it right
- Drop the debugfs_file field from struct irq_domain, now that
debugfs can track things on its own

show more ...

Merge drm/drm-next into drm-intel-next

Sync up with upstream.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up the fixes sent for v5.12 and continue development based on
v5.12-rc2, i.e. without the swap on file bug.

This also gets a sl

Merge remote-tracking branch 'torvalds/master' into perf/core

To pick up the fixes sent for v5.12 and continue development based on
v5.12-rc2, i.e. without the swap on file bug.

This also gets a slightly newer and better tools/perf/arch/arm/util/cs-etm.c
patch version, using the BIT() macro, that had already been slated to
v5.13 but ended up going to v5.12-rc1 on an older version.

Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

show more ...

Merge branch 'fixes-rc2' into fixes

scsi: core: Add scsi_device_busy() wrapper

Add scsi_device_busy() helper to prepare drivers for tracking device queue
depth via sbitmap_queue.

Link: https://lore.kernel.org/r/20210122023317.687987-

scsi: core: Add scsi_device_busy() wrapper

Add scsi_device_busy() helper to prepare drivers for tracking device queue
depth via sbitmap_queue.

Link: https://lore.kernel.org/r/20210122023317.687987-12-ming.lei@redhat.com
Cc: Omar Sandoval <osandov@fb.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Sumanesh Samanta <sumanesh.samanta@broadcom.com>
Cc: Ewan D. Milne <emilne@redhat.com>
Tested-by: Sumanesh Samanta <sumanesh.samanta@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

show more ...