net: ethernet: ti: am65-cpsw-nuss: fix irqs type

The K3 INTA driver, which is source TX/RX IRQs for CPSW NUSS, defines IRQs
triggering type as EDGE by default, but triggering type for CPSW NUSS TX/R

net: ethernet: ti: am65-cpsw-nuss: fix irqs type

The K3 INTA driver, which is source TX/RX IRQs for CPSW NUSS, defines IRQs
triggering type as EDGE by default, but triggering type for CPSW NUSS TX/RX
IRQs has to be LEVEL as the EDGE triggering type may cause unnecessary IRQs
triggering and NAPI scheduling for empty queues. It was discovered with
RT-kernel.

Fix it by explicitly specifying CPSW NUSS TX/RX IRQ type as
IRQF_TRIGGER_HIGH.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge branch 'net-ethernet-ti-k3-introduce-common-platform-time-sync-driver-cpts'

Grygorii Strashko says:

====================
net: ethernet: ti: k3: introduce common platform time sync driver - cp

Merge branch 'net-ethernet-ti-k3-introduce-common-platform-time-sync-driver-cpts'

Grygorii Strashko says:

====================
net: ethernet: ti: k3: introduce common platform time sync driver - cpts

This series introduced support for significantly upgraded TI A65x/J721E Common
platform time sync (CPTS) modules which are part of AM65xx Time Synchronization
Architecture [1].
The TI A65x/J721E now contain more than one CPTS instance:
- MCU CPSW CPTS (IEEE 1588 compliant)
- Main NAVSS CPTS (central)
- PCIe CPTS(s) (PTM compliant)
- J721E: Main CPSW9g CPTS (IEEE 1588 compliant)
which can work as separately as interact to each other through Time Sync Router
(TSR) and Compare Event Router (CER). In addition there are also ICSS-G IEP
blocks which can perform similar timsync functions, but require FW support.
More info also available in TRM [2][3]. Not all above modules are available
to the Linux by as of now as some of them are reserved for RTOS/FW purposes.

The scope of this submission is TI A65x/J721E CPSW CPTS and Main NAVSS CPTS,
and TSR was used for testing purposes.
+---------------------------+
| MCU CPSW |
+-------------------+ +------------------------+ | TS |
| Main Navss CPTS | | Time Sync Router (TSR) | | +-------------+ |
| | | | | | | |
| HW1_TS +<----------+ | | +--------v-----+ +--+--+
| | | | | | CPTS | |Port |
| ... | | | X+-->HW1_TS | | |
| HW8_TS <------------<---------+ | X|-->HW2_TS | +--^--+
| | | | +--------------->HW3_TS | | |
| | | | +--------------->HW4_TS | | |
| | | | | | | | | |
| | | | | | | | | |
| Genf0 +-----------> (A)---------+ +<--------------+Genf0 | | |
| | | | | | | | | |
| ... | | +-----------> <---------------+Genf1 ESTf+-------+ |
| | | | | | | |
| | | | | +--------------+ |
| Genf8 +---------->+ | | |
| | | SYNC0 ... SYNC3 | | |
+-------------------+ +------+------------+----+ +---------------------------+
+ +
X X
(A) shows possible routing path for MCU CPSW CPTS Genf0 signal as an example.

Main features of the new TI A65x/J721E CPTS modules are:
- 64-bit timestamp/counter mode support in ns by using add_val
- implemented in HW PPM and nudge adjustment.
- control of time sync events via interrupt or polling
- selection of multiple external reference clock sources
- hardware timestamp of ext. inputs events (HWx_TS_PUSH)
- periodic generator function outputs (TS_GENFx)
- (CPSW only) Ethernet Enhanced Scheduled Traffic Operations (CPTS_ESTFn),
which drives TSN schedule
- timestamping of all RX packets bypassing CPTS FIFO

Patch 1 - DT bindings
Patch 2 - the AM65x/J721E driver
Patch 3 - enables packet timestamping support in TI AM65x/J721E MCU CPSW driver.
Patches 4-7 - DT updates.

=== PTP Testing:

phc2sys -s CLOCK_REALTIME -c eth0 -m -O 0 -u30
phc2sys[627.331]: eth0 rms 409912446712787392 max 1587584079521858304 freq -6665 +/- 35040 delay 832 +/- 27
phc2sys[657.335]: eth0 rms 33 max 66 freq -0 +/- 28 delay 820 +/- 30
phc2sys[687.339]: eth0 rms 37 max 70 freq -1 +/- 32 delay 830 +/- 29
phc2sys[717.343]: eth0 rms 33 max 71 freq -0 +/- 29 delay 828 +/- 23
phc2sys[747.346]: eth0 rms 35 max 75 freq -0 +/- 31 delay 829 +/- 26
phc2sys[777.350]: eth0 rms 37 max 68 freq -1 +/- 32 delay 825 +/- 25
phc2sys[807.354]: eth0 rms 28 max 57 freq -1 +/- 25 delay 824 +/- 21
phc2sys[837.358]: eth0 rms 43 max 81 freq -1 +/- 37 delay 836 +/- 23
phc2sys[867.361]: eth0 rms 33 max 74 freq +0 +/- 29 delay 828 +/- 24
phc2sys[897.365]: eth0 rms 35 max 77 freq -2 +/- 30 delay 824 +/- 25
phc2sys[927.369]: eth0 rms 28 max 50 freq +0 +/- 25 delay 825 +/- 25

ptp4l -P -2 -H -i eth0 -l 6 -m -q -p /dev/ptp1 -f ptp.cfg -s
ptp4l[22095.754]: port 1: MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[22097.754]: port 1: UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[22159.757]: rms 317 max 1418 freq +79 +/- 186 delay 410 +/- 1
ptp4l[22223.760]: rms 9 max 24 freq +42 +/- 12 delay 409 +/- 1
ptp4l[22287.763]: rms 10 max 28 freq +41 +/- 11 delay 410 +/- 1
ptp4l[22351.767]: rms 10 max 26 freq +34 +/- 12 delay 410 +/- 1
ptp4l[22415.770]: rms 10 max 26 freq +49 +/- 14 delay 410 +/- 1

=== Ext. HW_TS and Genf testing:

For testing purposes Time Sync Router (TSR) can be modeled in DT as pin controller
+ timesync_router: timesync_router@A40000 {
+ compatible = "pinctrl-single";
+ reg = <0x0 0xA40000 0x0 0x800>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #pinctrl-cells = <1>;
+ pinctrl-single,register-width = <32>;
+ pinctrl-single,function-mask = <0x800007ff>;
+ };

then signals routing can be done in board file, for example:
+#define TS_OFFSET(pa, val) (0x4+(pa)*4) (0x80000000 | val)
+
+&timesync_router {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mcu_cpts>;
+
+ /* Example of the timesync routing */
+ mcu_cpts: mcu_cpts {
+ pinctrl-single,pins = <
+ /* [cpts genf1] in13 -> out25 [cpts hw4_push] */
+ TS_OFFSET(25, 13)
+ /* [cpts genf1] in13 -> out0 [main cpts hw1_push] */
+ TS_OFFSET(0, 13)
+ /* [main cpts genf0] in4 -> out1 [main cpts hw2_push] */
+ TS_OFFSET(1, 4)
+ /* [main cpts genf0] in4 -> out24 [cpts hw3_push] */
+ TS_OFFSET(24, 4)
+ >;
+ };
+};

will create link:
cpsw cpts Genf1 -> main cpts hw1_push
-> cpsw cpts hw4_push

main cpts Genf0 -> main cpts hw2_push
-> cpsw cpts hw3_push

testptp -d /dev/ptp0 -i 0 -p 1000000000
periodic output request okay
testptp -d /dev/ptp0 -i 1 -e 5
external time stamp request okay
event index 1 at 22583.000000025
event index 1 at 22584.000000025
event index 1 at 22585.000000025
event index 1 at 22586.000000025
event index 1 at 22587.000000025
testptp -d /dev/ptp1 -i 2 -e 5
external time stamp request okay
event index 2 at 1587606764.249304554
event index 2 at 1587606765.249304467
event index 2 at 1587606766.249304380
event index 2 at 1587606767.249304293
event index 2 at 1587606768.249304206

[1] https://www.ti.com/lit/pdf/spracp7
[2] https://www.ti.com/lit/pdf/sprz452
[3] https://www.ti.com/lit/pdf/spruil1
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

This enables

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

This enables corresponding support in TI AM65x/J721E MCU CPSW driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge tag 'v5.7-rc3' into spi-5.8

Linux 5.7-rc3

Merge 5.7-rc3 into staging-next

We need the staging fixes in here too, and this resolves a merge issue
with the vt6656 driver.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.7-rc3 into driver-core-next

We need the driver core fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.7-rc3 into tty-next

We need the tty/serial fixes in here too.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge 5.7-rc3 into usb-next

We need the USB fixes in here too.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core

Pull EFI changes for v5.8 from Ard Biesheuvel:

"- preliminary changes for RISC-V
- add support for setti

Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core

Pull EFI changes for v5.8 from Ard Biesheuvel:

"- preliminary changes for RISC-V
- add support for setting the resolution on the EFI framebuffer
- simplify kernel image loading for arm64
- Move .bss into .data via the linker script instead of relying on symbol
annotations.
- Get rid of __pure getters to access global variables
- Clean up the config table matching arrays"

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

Merge branch 'topic/nhlt' into for-next

Merge NHLT init cleanup.

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge tag 'tegra-for-5.7-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into asoc-5.7

ASoC: tegra: Fixes for v5.7-rc3

This contains a couple of fixes that are needed to properly

Merge tag 'tegra-for-5.7-asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into asoc-5.7

ASoC: tegra: Fixes for v5.7-rc3

This contains a couple of fixes that are needed to properly reconfigure
the audio clocks on older Tegra devices.

show more ...

Merge branch 'fixes-v5.7' into fixes

Merge tag 'kvm-s390-master-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master

KVM: s390: Fix for 5.7 and maintainer update

- Silence false positive lockdep warnin

Merge tag 'kvm-s390-master-5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-master

KVM: s390: Fix for 5.7 and maintainer update

- Silence false positive lockdep warning
- add Claudio as reviewer

show more ...

Merge branch 'ib-pdx86-properties'

Merge branch 'ib-pdx86-properties' of
git://git.infradead.org/linux-platform-drivers-x86.git
to avoid conflicts in PDx86.

Signed-off-by: Andy Shevchenko <andriy.s

Merge branch 'ib-pdx86-properties'

Merge branch 'ib-pdx86-properties' of
git://git.infradead.org/linux-platform-drivers-x86.git
to avoid conflicts in PDx86.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>

show more ...

Merge tag 'v5.7-rc2' into patchwork

Linux 5.7-rc2

* tag 'v5.7-rc2': (331 commits)
Linux 5.7-rc2
mm: Fix MREMAP_DONTUNMAP accounting on VMA merge
xattr.h: Replace zero-length array with flexib

Merge tag 'v5.7-rc2' into patchwork

Linux 5.7-rc2

* tag 'v5.7-rc2': (331 commits)
Linux 5.7-rc2
mm: Fix MREMAP_DONTUNMAP accounting on VMA merge
xattr.h: Replace zero-length array with flexible-array member
uapi: linux: fiemap.h: Replace zero-length array with flexible-array member
uapi: linux: dlm_device.h: Replace zero-length array with flexible-array member
tpm_eventlog.h: Replace zero-length array with flexible-array member
ti_wilink_st.h: Replace zero-length array with flexible-array member
swap.h: Replace zero-length array with flexible-array member
skbuff.h: Replace zero-length array with flexible-array member
sched: topology.h: Replace zero-length array with flexible-array member
rslib.h: Replace zero-length array with flexible-array member
rio.h: Replace zero-length array with flexible-array member
posix_acl.h: Replace zero-length array with flexible-array member
platform_data: wilco-ec.h: Replace zero-length array with flexible-array member
memcontrol.h: Replace zero-length array with flexible-array member
list_lru.h: Replace zero-length array with flexible-array member
lib: cpu_rmap: Replace zero-length array with flexible-array member
irq.h: Replace zero-length array with flexible-array member
ihex.h: Replace zero-length array with flexible-array member
igmp.h: Replace zero-length array with flexible-array member
...

show more ...

Merge drm/drm-next into drm-misc-next

Backmerging required to pull topic/phy-compliance.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.

2) nf_tables leaves dangling

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net

Pull networking fixes from David Miller:

1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.

2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.

3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.

4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.

5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.

6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.

7) Missing release firmware call in mlx5, from Eran Ben Elisha.

8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.

9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.

10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.

11) Fix double unlock in mptcp, from Florian Westphal.

12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.

13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.

14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...

show more ...

Merge drm/drm-next into drm-intel-next-queued

Backmerging in order to pull "topic/phy-compliance".

Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>

Merge v5.7-rc1 into drm-misc-fixes

Start the new drm-misc-fixes cycle.

Signed-off-by: Maxime Ripard <maxime@cerno.tech>

Merge tag 'v5.7-rc1' into locking/kcsan, to resolve conflicts and refresh

Resolve these conflicts:

arch/x86/Kconfig
arch/x86/kernel/Makefile

Do a minor "evil merge" to move the KCSAN entry up a

Merge tag 'v5.7-rc1' into locking/kcsan, to resolve conflicts and refresh

Resolve these conflicts:

arch/x86/Kconfig
arch/x86/kernel/Makefile

Do a minor "evil merge" to move the KCSAN entry up a bit by a few lines
in the Kconfig to reduce the probability of future conflicts.

Signed-off-by: Ingo Molnar <mingo@kernel.org>

show more ...

net: ethernet: ti: Add missing '\n' in log messages

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth su

net: ethernet: ti: Add missing '\n' in log messages

Message logged by 'dev_xxx()' or 'pr_xxx()' should end with a '\n'.

Fixes: 93a76530316a ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:
"Highlights:

1) Fix the iwlwifi regression, from Johannes Berg.

2) Support BSS

Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next

Pull networking updates from David Miller:
"Highlights:

1) Fix the iwlwifi regression, from Johannes Berg.

2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.

3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.

4) Add TTL decrement action to openvswitch, from Matteo Croce.

5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.

6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.

7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.

8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.

9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.

10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.

11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.

12) Support bcmgenet on ACPI, from Jeremy Linton.

13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.

14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.

15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.

16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.

17) Offload FIFO qdisc in mlxsw, from Petr Machata.

18) Support UDP sockets in sockmap, from Lorenz Bauer.

19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.

20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.

21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.

22) Add support for hw offload of MACSEC, from Antoine Tenart.

23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.

24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.

25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...

show more ...

net: ethernet: ti: fix spelling mistake "rundom" -> "random"

There is a spelling mistake in a dev_err error message. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by:

net: ethernet: ti: fix spelling mistake "rundom" -> "random"

There is a spelling mistake in a dev_err error message. Fix it.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Merge branch 'net-ethernet-ti-add-networking-support-for-k3-am65x-j721e-soc'

Grygorii Strashko says:

====================
net: ethernet: ti: add networking support for k3 am65x/j721e soc

This v6 s

Merge branch 'net-ethernet-ti-add-networking-support-for-k3-am65x-j721e-soc'

Grygorii Strashko says:

====================
net: ethernet: ti: add networking support for k3 am65x/j721e soc

This v6 series adds basic networking support support TI K3 AM654x/J721E SoC which
have integrated Gigabit Ethernet MAC (Media Access Controller) into device MCU
domain and named MCU_CPSW0 (CPSW2G NUSS).

Formally TRMs refer CPSW2G NUSS as two-port Gigabit Ethernet Switch subsystem
with port 0 being the CPPI DMA host port and port 1 being the external Ethernet
port, but for 1 external port device it's just Port 0 <-> ALE <-> Port 1 and it's
rather device with HW filtering capabilities then actually switching device.
It's expected to have similar devices, but with more external ports.

The new Host port 0 Communications Port Programming Interface (CPPI5) is
operating by TI AM654x/J721E NAVSS Unified DMA Peripheral Root Complex (UDMA-P)
controller [1].

The CPSW2G contains below modules for which existing code is re-used:
- MAC SL: cpsw_sl.c
- Address Lookup Engine (ALE): cpsw_ale.c, basically compatible with K2 66AK2E/G
- Management Data Input/Output interface (MDIO): davinci_mdio.c, fully
compatible with TI AM3/4/5 devices

Basic features supported by CPSW2G NUSS driver:
- VLAN support, 802.1Q compliant, Auto add port VLAN for untagged frames on
ingress, Auto VLAN removal on egress and auto pad to minimum frame size.
- multicast filtering
- promisc mode
- TX multiq support in Round Robin or Fixed priority modes
- RX checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets
- TX checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).

Features under development:
- Support for IEEE 1588 Clock Synchronization. The CPSW2G NUSS includes new
version of Common Platform Time Sync (CPTS)
- tc-mqprio: priority level Quality Of Service (QOS) support (802.1p)
- tc-cbs: Support for Audio/Video Bridging (P802.1Qav/D6.0) HW shapers
- tc-taprio: IEEE 802.1Qbv/D2.2 Enhancements for Scheduled Traffic
- frame preemption: IEEE P902.3br/D2.0 Interspersing Express Traffic, 802.1Qbu
- extended ALE features: classifier/policers, auto-aging

Patches 1-6 are intended for netdev, Patches 7-11 are intended for K3 Platform
tree and provided here for testing purposes.

Changes in v6:
- fixed comments from Rob Herring <robh@kernel.org> and added his Reviewed-by.
- added Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>

Changes in v5:
- renamed files k3-udma-desc-pool.* k3-udma-desc-pool to k3-cppi-desc-pool.*,
and API to k3_cppi_desc_pool_* as requested by Peter Ujfalusi <peter.ujfalusi@ti.com>
- fixed copy-paste err in am65_cpsw_nuss_ndo_slave_set_rx_mode() which blocked
recieving of mcast frames.
- added Tested-by: Murali Karicheri <m-karicheri2@ti.com>

Changes in v4:
- fixed minor comments from Jakub Kicinski <kuba@kernel.org>
- dependencies resolved: required phy-rmii-sel changes [2] queued for merge
except one [3] which is included in this series with Kishon's ask.

Changes in v3:
- add ARM64 defconfig changes for testing purposes
- fixed DT yaml definition
- fixed comments from Jakub Kicinski <kuba@kernel.org>

Changes in v2:
- fixed DT yaml definition
- fixed comments from David Miller

v5: https://patchwork.ozlabs.org/cover/1258295/
v4: https://patchwork.ozlabs.org/cover/1256092/
v3: https://patchwork.ozlabs.org/cover/1254568/
v2: https://patchwork.ozlabs.org/cover/1250674/
v1: https://lwn.net/Articles/813087/

TRMs:
AM654: http://www.ti.com/lit/ug/spruid7e/spruid7e.pdf
J721E: http://www.ti.com/lit/ug/spruil1a/spruil1a.pdf

Preliminary documentation can be found at:
http://software-dl.ti.com/processor-sdk-linux/esd/docs/latest/linux/Foundational_Components/Kernel/Kernel_Drivers/Network/K3_CPSW2g.html

[1] https://lwn.net/Articles/808030/
[2] https://lkml.org/lkml/2020/2/22/100
[3] https://lkml.org/lkml/2020/3/3/724
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectab

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
- Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
- Updated Address Lookup Engine (ALE) module;
- (TBD) New version of Common platform time sync (CPTS) module.

On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.

Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.

Introduced driver provides standard Linux net_device to user space and supports:
- ifconfig up/down
- MAC address configuration
- ethtool operation:
--driver
--change
--register-dump
--negotiate phy
--statistics
--set-eee phy
--show-ring
--show-channels
--set-channels
- net_device ioctl mii-control
- promisc mode

- rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
csum information for each packet in psdata[2] word:
- BIT(16) CHECKSUM_ERROR - indicates csum error
- BIT(17) FRAGMENT - indicates fragmented packet
- BIT(18) TCP_UDP_N - Indicates TCP packet was detected
- BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
- BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
during the checksum computation. This value is FFFFh for non fragmented
IPV4/6 UDP/TCP packets with no checksum error.

RX csum offload can be disabled:
ethtool -K <dev> rx-checksum on|off

- tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
TX csum HW offload can be enabled/disabled:
ethtool -K <dev> tx-checksum-ip-generic on|off

- multiq and switch between round robin/prio modes for cppi tx queues by
using Netdev private flag "p0-rx-ptype-rrobin" to switch between
Round Robin and Fixed priority modes:
# ethtool --show-priv-flags eth0
Private flags for eth0:
p0-rx-ptype-rrobin: on
# ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".

- GRO support: the napi_gro_receive() and napi_complete_done() are used.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...