Merge tag 'staging-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging and IIO driver updates from Greg KH:
"Here is the big Staging and IIO driver update for 4.8-

Merge tag 'staging-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging

Pull staging and IIO driver updates from Greg KH:
"Here is the big Staging and IIO driver update for 4.8-rc1.

We ended up adding more code than removing, again, but it's not all
that bad. Lots of cleanups all over the staging tree, and new IIO
drivers, full details in the shortlog.

All of these have been in linux-next for a while with no reported
issues"

* tag 'staging-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (417 commits)
drivers:iio:accel:mma8452: removed unwanted return statements
drivers:iio:accel:mma8452: added cleanup provision in case of failure.
iio: Add iio.git tree to MAINTAINERS
iio:st_pressure: clean useless static channel initializers
iio:st_pressure:lps22hb: temperature support
iio:st_pressure:lps22hb: open drain support
iio:st_pressure: temperature triggered buffering
iio:st_pressure: document sampling gains
iio:st_pressure: align storagebits on power of 2
iio:st_sensors: align on storagebits boundaries
staging:iio:lis3l02dq drop separate driver
iio: accel: st_accel: Add lis3l02dq support
iio: adc: add missing of_node references to iio_dev
iio: adc: ti-ads1015: add indio_dev->dev.of_node reference
iio: potentiometer: Fix typo in Kconfig
iio: potentiometer: mcp4531: Add device tree binding
iio: potentiometer: mcp4531: Add device tree binding documentation
iio: potentiometer: mcp4531: Add support for MCP454x, MCP456x, MCP464x and MCP466x
iio:imu:mpu6050: icm20608 initial support
iio: adc: max1363: Add device tree binding
...

show more ...

Merge tag 'iio-for-4.8c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Third set of IIO new device support, features and cleanups for the 4.8 cycle.

Merge tag 'iio-for-4.8c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

Third set of IIO new device support, features and cleanups for the 4.8 cycle.

New core features
- Selection of the clock source for IIO timestamps. This is done per device
as it makes little sense to have events in one timebase and data timestamped
on another. Biggest reason for this is that we currently use a clock
source which is non monotonic which can result in 'interesting' data sets.
(Includes export for get_monotonic_corse64 which Thomas Gleixner didn't mind
in an earlier version.)
- MAINTAINERS add the git tree to the list for IIO.

New device support + a kind of indirect staging graduation.
* Broadcom iproc-static-adc
- new driver
* mcp4531
- support for MCP454x, MCP456x, MCP464x and MCP466x potentiometers
* mpu6050
- support the IC20608 6 axis motion tracking device
* st-sensors
- support the lis3l02dq + drop the lis3l02dq driver from staging.
The general purpose driver is missing event support, but good to get
rid of this driver which was rather long in the tooth.

New driver features
* ak8975
- Add vid regulator support and refactor handling in general.
- Allow a delay after enabling regulators.
- Runtime and system PM.
* bmg160
- filter frequency control support.
* bmp280
- SPI device support.
- EOC interrupt support for the BMP085
- power management support.
- supply regulator support.
- reset gpio support
- dt bindings for reset gpio and regulators.
- of table to support device tree registration
* max1363
- Device tree bindings.
* mcp4531
- Device tree bindings.
* st-pressure
- temperature channels as part of triggered buffer (previously not due
probably to alignment issues - see below).
- lps22hb open drain interrupt support.
- lps22hb temperature channel support

Cleanups and reworkings.
* numerous ADC drivers
- ensure the iio_dev->dev.of_node is set to the parent dev.of_node so
as to allow client bindings to find the device.
* ak8975
- Fix incorrect handling of missing regulator
- make sure power is down and remove.
* bmp280
- read the calibration data only once as it doesn't change.
* isl29125
- Use a few macros to make code a touch more readable.
* mma8452
- fix a memory leak on error.
- drop an unecessary bit of return value handling.
* potentiometer kconfig
- typo fix.
* st-pressure
- drop some uninformative default assignments of elements of the channel
array structure (aids readability).
* st-sensors
- Harden interrupt handling considerably. These are actually all using
level interrupts, but at least two known boards have them wired to
edge only interrupt chips. Hence a slightly interesting bit of handling
is needed in which we first allow for the easy option (level triggered) and
secondly check the status registers before reenabling edge interrupts and
fall back to a tight loop in the thread until we successfully clear the
interrupt. No harm is done if we never succeed in doing so. It's an odd
patch that has been through a lot of revisions to reach a consensus on how
to handle what is basically broken hardware (which the previous defaults
allowed to kind of work).
- Fix alignment to defined storagebytes boundaries.
- Ensure alignment of power of 2 byte boundaries. This has always in theory
been part of the ABI of IIO, but we missed a few that snuck in that need
fixing. The effect was minor as they were only followed by timestamp
channels which were correctly aligned,
- Add some docs to explain the gain calculations.

show more ...

iio: pressure: bmp280: split off an I2C Kconfig entry

This creates a separate BMP280_I2C Kconfig entry that gets selected
by BMP280 for I2C transport. As we currently only support I2C
transport ther

iio: pressure: bmp280: split off an I2C Kconfig entry

This creates a separate BMP280_I2C Kconfig entry that gets selected
by BMP280 for I2C transport. As we currently only support I2C
transport there is not much practical change other than getting
a separate object file (or module) for the I2C driver part. The
old Kconfig symbol BMP280 will still select the stuff we need so
that oldconfig and old defconfigs works fine.

Tested-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...

iio: pressure: bmp280: split driver in logical parts

This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,

iio: pressure: bmp280: split driver in logical parts

This splits the BMP280 driver in three logical parts: the core driver
bmp280-core that only operated on a struct device * and a struct regmap *,
the regmap driver bmp280-regmap that can be shared between I2C and other
transports and the I2C module driver bmp280-i2c.

Cleverly bake all functionality into a single object bmp280.o so that
we still get the same module binary built for the device in the end,
without any fuzz exporting symbols to the left and right.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

show more ...