| /openbmc/u-boot/board/warp7/ |
| H A D | README | 29 Connect a USB cable between the OTG warp7 port and the host PC
|
| /openbmc/linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | bq24190.yaml | 34 either USB host mode or for charging on the OTG port
|
| /openbmc/linux/Documentation/devicetree/bindings/usb/ |
| H A D | mediatek,musb.yaml | 8 title: MediaTek MUSB DRD/OTG Controller
|
| H A D | fsl,imx8qm-cdns3.yaml | 90 reg = <0x5b120000 0x10000>, /* memory area for OTG/DRD registers */
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | sun8i-h2-plus-bananapi-m2-zero.dts | 116 * OTG. The Vbus of these two connectors are connected together, so
|
| /openbmc/u-boot/board/technexion/pico-imx7d/ |
| H A D | README | 27 Connect a USB cable between the OTG pico port and the host PC.
|
| /openbmc/u-boot/board/freescale/mpc837xerdb/ |
| H A D | README | 20 J) 1-port OTG USB
|
| /openbmc/u-boot/board/freescale/ls1043aqds/ |
| H A D | README | 32 - The other two USB 3.0 ports configured as OTG with micro-AB connector
|
| /openbmc/linux/drivers/usb/common/ |
| H A D | Kconfig | 32 ULPI PHYs provide often functions such as ADP sensing/probing (OTG
|
| /openbmc/linux/drivers/gpu/drm/amd/display/dc/dcn31/ |
| H A D | dcn31_resource.c | 688 SRII(PIXEL_RATE_CNTL, OTG, 0), \
689 SRII(PIXEL_RATE_CNTL, OTG, 1),\
690 SRII(PIXEL_RATE_CNTL, OTG, 2),\
691 SRII(PIXEL_RATE_CNTL, OTG, 3),\
692 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 0),\
693 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 1),\
694 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 2),\
695 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 3),\
|
| /openbmc/u-boot/drivers/phy/ |
| H A D | Kconfig | 127 PHY connected to EHCI USB module and controls USB OTG operation.
139 between an HS USB OTG controller and an HS USB Host controller,
|
| /openbmc/linux/arch/arm64/boot/dts/renesas/ |
| H A D | ulcb-kf.dtsi | 266 line-name = "OTG EXTLPn";
273 line-name = "OTG OFFVBUSn";
|
| /openbmc/u-boot/board/freescale/ls1046aqds/ |
| H A D | README | 32 - The other two USB 3.0 ports configured as OTG with micro-AB connector
|
| /openbmc/u-boot/board/theobroma-systems/lion_rk3368/ |
| H A D | README | 44 rkdeveloptool allows to flash the on-board eMMC via the USB OTG interface with
|
| /openbmc/linux/Documentation/driver-api/usb/ |
| H A D | writing_musb_glue_layer.rst | 15 Instead, these embedded UDC rely on the USB On-the-Go (OTG)
34 Resources) which provides an introduction of USB OTG operation at the
239 between OTG and non-OTG modes, for instance.
525 /* Silicon does not implement USB OTG. */
544 Defining the OTG capability of the controller hardware, the multipoint
546 is not OTG compatible. Then ``num_eps`` (line 5) defines the number of USB
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | x-powers,axp152.yaml | 133 external regulator to drive the OTG VBus, rather then as an input pin
134 which signals whether the board is driving OTG VBus or not.
|
| /openbmc/linux/Documentation/devicetree/bindings/phy/ |
| H A D | nvidia,tegra194-xusb-padctl.yaml | 248 supports OTG or peripheral mode. If present, the port
286 supports OTG or peripheral mode. If present, the port
324 supports OTG or peripheral mode. If present, the port
362 supports OTG or peripheral mode. If present, the port
|
| H A D | renesas,usb2-phy.yaml | 60 - 3 = UCOM_INT (OTG and BC)
|
| /openbmc/linux/arch/arm/boot/dts/qcom/ |
| H A D | qcom-apq8064-cm-qs600.dts | 216 /* OTG */
|
| /openbmc/linux/arch/arm64/boot/dts/freescale/ |
| H A D | imx8mp-venice-gw71xx.dtsi | 127 /* dual role is implemented but not a full featured OTG */
|
| H A D | imx8mn-var-som-symphony.dts | 83 /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
|
| /openbmc/u-boot/board/sunxi/ |
| H A D | README.sunxi64 | 90 4) Initialize the USB OTG controller and will wait for a host to connect to
96 FEL boot (USB OTG)
100 by using the USB-OTG interface and a host port on another computer.
|
| /openbmc/linux/drivers/usb/host/ |
| H A D | Kconfig | 11 The Cypress C67x00 (EZ-Host/EZ-OTG) chips are dual-role
12 host/peripheral/OTG USB controllers.
311 USB SPH and OTG controller. SPH is a single port host, and it can
312 only be EHCI host. OTG is controller that can switch to host mode.
356 The OXU210HP is an USB host/OTG/device controller. Enable this
360 implement OTG nor USB device controllers.
|
| /openbmc/u-boot/board/amlogic/odroid-c2/ |
| H A D | README.nanopi-k2 | 13 - 4 x USB 2.0 Host, 1 x USB OTG
|
| /openbmc/linux/Documentation/gpu/amdgpu/display/ |
| H A D | dc-glossary.rst | 200 OTG
|