1// SPDX-License-Identifier: BSD-3-Clause 2/* 3 * SDX55 SoC device tree source 4 * 5 * Copyright (c) 2018, The Linux Foundation. All rights reserved. 6 * Copyright (c) 2020, Linaro Ltd. 7 */ 8 9#include <dt-bindings/clock/qcom,gcc-sdx55.h> 10#include <dt-bindings/clock/qcom,rpmh.h> 11#include <dt-bindings/gpio/gpio.h> 12#include <dt-bindings/interconnect/qcom,sdx55.h> 13#include <dt-bindings/interrupt-controller/arm-gic.h> 14#include <dt-bindings/power/qcom-rpmpd.h> 15#include <dt-bindings/soc/qcom,rpmh-rsc.h> 16 17/ { 18 #address-cells = <1>; 19 #size-cells = <1>; 20 qcom,msm-id = <357 0x10000>, <368 0x10000>, <418 0x10000>; 21 interrupt-parent = <&intc>; 22 23 memory { 24 device_type = "memory"; 25 reg = <0 0>; 26 }; 27 28 clocks { 29 xo_board: xo-board { 30 compatible = "fixed-clock"; 31 #clock-cells = <0>; 32 clock-frequency = <38400000>; 33 clock-output-names = "xo_board"; 34 }; 35 36 sleep_clk: sleep-clk { 37 compatible = "fixed-clock"; 38 #clock-cells = <0>; 39 clock-frequency = <32000>; 40 }; 41 42 nand_clk_dummy: nand-clk-dummy { 43 compatible = "fixed-clock"; 44 #clock-cells = <0>; 45 clock-frequency = <32000>; 46 }; 47 }; 48 49 cpus { 50 #address-cells = <1>; 51 #size-cells = <0>; 52 53 cpu0: cpu@0 { 54 device_type = "cpu"; 55 compatible = "arm,cortex-a7"; 56 reg = <0x0>; 57 enable-method = "psci"; 58 clocks = <&apcs>; 59 power-domains = <&rpmhpd SDX55_CX>; 60 power-domain-names = "rpmhpd"; 61 operating-points-v2 = <&cpu_opp_table>; 62 }; 63 }; 64 65 firmware { 66 scm { 67 compatible = "qcom,scm-sdx55", "qcom,scm"; 68 }; 69 }; 70 71 cpu_opp_table: opp-table-cpu { 72 compatible = "operating-points-v2"; 73 opp-shared; 74 75 opp-345600000 { 76 opp-hz = /bits/ 64 <345600000>; 77 required-opps = <&rpmhpd_opp_low_svs>; 78 }; 79 80 opp-576000000 { 81 opp-hz = /bits/ 64 <576000000>; 82 required-opps = <&rpmhpd_opp_svs>; 83 }; 84 85 opp-1094400000 { 86 opp-hz = /bits/ 64 <1094400000>; 87 required-opps = <&rpmhpd_opp_nom>; 88 }; 89 90 opp-1555200000 { 91 opp-hz = /bits/ 64 <1555200000>; 92 required-opps = <&rpmhpd_opp_turbo>; 93 }; 94 }; 95 96 psci { 97 compatible = "arm,psci-1.0"; 98 method = "smc"; 99 }; 100 101 reserved-memory { 102 #address-cells = <1>; 103 #size-cells = <1>; 104 ranges; 105 106 hyp_mem: memory@8fc00000 { 107 no-map; 108 reg = <0x8fc00000 0x80000>; 109 }; 110 111 ac_db_mem: memory@8fc80000 { 112 no-map; 113 reg = <0x8fc80000 0x40000>; 114 }; 115 116 secdata_mem: memory@8fcfd000 { 117 no-map; 118 reg = <0x8fcfd000 0x1000>; 119 }; 120 121 sbl_mem: memory@8fd00000 { 122 no-map; 123 reg = <0x8fd00000 0x100000>; 124 }; 125 126 aop_image: memory@8fe00000 { 127 no-map; 128 reg = <0x8fe00000 0x20000>; 129 }; 130 131 aop_cmd_db: memory@8fe20000 { 132 compatible = "qcom,cmd-db"; 133 reg = <0x8fe20000 0x20000>; 134 no-map; 135 }; 136 137 smem_mem: memory@8fe40000 { 138 no-map; 139 reg = <0x8fe40000 0xc0000>; 140 }; 141 142 tz_mem: memory@8ff00000 { 143 no-map; 144 reg = <0x8ff00000 0x100000>; 145 }; 146 147 tz_apps_mem: memory@90000000 { 148 no-map; 149 reg = <0x90000000 0x500000>; 150 }; 151 }; 152 153 smem { 154 compatible = "qcom,smem"; 155 memory-region = <&smem_mem>; 156 hwlocks = <&tcsr_mutex 3>; 157 }; 158 159 smp2p-mpss { 160 compatible = "qcom,smp2p"; 161 qcom,smem = <435>, <428>; 162 interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>; 163 mboxes = <&apcs 14>; 164 qcom,local-pid = <0>; 165 qcom,remote-pid = <1>; 166 167 modem_smp2p_out: master-kernel { 168 qcom,entry-name = "master-kernel"; 169 #qcom,smem-state-cells = <1>; 170 }; 171 172 modem_smp2p_in: slave-kernel { 173 qcom,entry-name = "slave-kernel"; 174 interrupt-controller; 175 #interrupt-cells = <2>; 176 }; 177 178 ipa_smp2p_out: ipa-ap-to-modem { 179 qcom,entry-name = "ipa"; 180 #qcom,smem-state-cells = <1>; 181 }; 182 183 ipa_smp2p_in: ipa-modem-to-ap { 184 qcom,entry-name = "ipa"; 185 interrupt-controller; 186 #interrupt-cells = <2>; 187 }; 188 }; 189 190 soc: soc { 191 #address-cells = <1>; 192 #size-cells = <1>; 193 ranges; 194 compatible = "simple-bus"; 195 196 gcc: clock-controller@100000 { 197 compatible = "qcom,gcc-sdx55"; 198 reg = <0x100000 0x1f0000>; 199 #clock-cells = <1>; 200 #reset-cells = <1>; 201 #power-domain-cells = <1>; 202 clock-names = "bi_tcxo", "sleep_clk"; 203 clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>; 204 }; 205 206 blsp1_uart3: serial@831000 { 207 compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; 208 reg = <0x00831000 0x200>; 209 interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; 210 clocks = <&gcc 30>, 211 <&gcc 9>; 212 clock-names = "core", "iface"; 213 status = "disabled"; 214 }; 215 216 usb_hsphy: phy@ff4000 { 217 compatible = "qcom,sdx55-usb-hs-phy", 218 "qcom,usb-snps-hs-7nm-phy"; 219 reg = <0x00ff4000 0x114>; 220 status = "disabled"; 221 #phy-cells = <0>; 222 223 clocks = <&rpmhcc RPMH_CXO_CLK>; 224 clock-names = "ref"; 225 226 resets = <&gcc GCC_QUSB2PHY_BCR>; 227 }; 228 229 usb_qmpphy: phy@ff6000 { 230 compatible = "qcom,sdx55-qmp-usb3-uni-phy"; 231 reg = <0x00ff6000 0x1c0>; 232 status = "disabled"; 233 #address-cells = <1>; 234 #size-cells = <1>; 235 ranges; 236 237 clocks = <&gcc GCC_USB3_PHY_AUX_CLK>, 238 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, 239 <&gcc GCC_USB3_PRIM_CLKREF_CLK>; 240 clock-names = "aux", "cfg_ahb", "ref"; 241 242 resets = <&gcc GCC_USB3PHY_PHY_BCR>, 243 <&gcc GCC_USB3_PHY_BCR>; 244 reset-names = "phy", "common"; 245 246 usb_ssphy: phy@ff6200 { 247 reg = <0x00ff6200 0x170>, 248 <0x00ff6400 0x200>, 249 <0x00ff6800 0x800>; 250 #phy-cells = <0>; 251 #clock-cells = <0>; 252 clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>; 253 clock-names = "pipe0"; 254 clock-output-names = "usb3_uni_phy_pipe_clk_src"; 255 }; 256 }; 257 258 mc_virt: interconnect@1100000 { 259 compatible = "qcom,sdx55-mc-virt"; 260 reg = <0x01100000 0x400000>; 261 #interconnect-cells = <1>; 262 qcom,bcm-voters = <&apps_bcm_voter>; 263 }; 264 265 mem_noc: interconnect@9680000 { 266 compatible = "qcom,sdx55-mem-noc"; 267 reg = <0x09680000 0x40000>; 268 #interconnect-cells = <1>; 269 qcom,bcm-voters = <&apps_bcm_voter>; 270 }; 271 272 system_noc: interconnect@162c000 { 273 compatible = "qcom,sdx55-system-noc"; 274 reg = <0x0162c000 0x31200>; 275 #interconnect-cells = <1>; 276 qcom,bcm-voters = <&apps_bcm_voter>; 277 }; 278 279 qpic_bam: dma-controller@1b04000 { 280 compatible = "qcom,bam-v1.7.0"; 281 reg = <0x01b04000 0x1c000>; 282 interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>; 283 clocks = <&rpmhcc RPMH_QPIC_CLK>; 284 clock-names = "bam_clk"; 285 #dma-cells = <1>; 286 qcom,ee = <0>; 287 qcom,controlled-remotely; 288 status = "disabled"; 289 }; 290 291 qpic_nand: nand-controller@1b30000 { 292 compatible = "qcom,sdx55-nand"; 293 reg = <0x01b30000 0x10000>; 294 #address-cells = <1>; 295 #size-cells = <0>; 296 clocks = <&rpmhcc RPMH_QPIC_CLK>, 297 <&nand_clk_dummy>; 298 clock-names = "core", "aon"; 299 300 dmas = <&qpic_bam 0>, 301 <&qpic_bam 1>, 302 <&qpic_bam 2>; 303 dma-names = "tx", "rx", "cmd"; 304 status = "disabled"; 305 }; 306 307 pcie_rc: pcie@1c00000 { 308 compatible = "qcom,pcie-sdx55"; 309 reg = <0x01c00000 0x3000>, 310 <0x40000000 0xf1d>, 311 <0x40000f20 0xc8>, 312 <0x40001000 0x1000>, 313 <0x40100000 0x100000>; 314 reg-names = "parf", 315 "dbi", 316 "elbi", 317 "atu", 318 "config"; 319 device_type = "pci"; 320 linux,pci-domain = <0>; 321 bus-range = <0x00 0xff>; 322 num-lanes = <1>; 323 324 #address-cells = <3>; 325 #size-cells = <2>; 326 327 ranges = <0x01000000 0x0 0x00000000 0x40200000 0x0 0x100000>, 328 <0x02000000 0x0 0x40300000 0x40300000 0x0 0x3fd00000>; 329 330 interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, 331 <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, 332 <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, 333 <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, 334 <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, 335 <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, 336 <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, 337 <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; 338 interrupt-names = "msi", 339 "msi2", 340 "msi3", 341 "msi4", 342 "msi5", 343 "msi6", 344 "msi7", 345 "msi8"; 346 #interrupt-cells = <1>; 347 interrupt-map-mask = <0 0 0 0x7>; 348 interrupt-map = <0 0 0 1 &intc 0 141 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ 349 <0 0 0 2 &intc 0 142 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ 350 <0 0 0 3 &intc 0 143 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ 351 <0 0 0 4 &intc 0 144 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ 352 353 clocks = <&gcc GCC_PCIE_PIPE_CLK>, 354 <&gcc GCC_PCIE_AUX_CLK>, 355 <&gcc GCC_PCIE_CFG_AHB_CLK>, 356 <&gcc GCC_PCIE_MSTR_AXI_CLK>, 357 <&gcc GCC_PCIE_SLV_AXI_CLK>, 358 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>, 359 <&gcc GCC_PCIE_SLEEP_CLK>; 360 clock-names = "pipe", 361 "aux", 362 "cfg", 363 "bus_master", 364 "bus_slave", 365 "slave_q2a", 366 "sleep"; 367 368 assigned-clocks = <&gcc GCC_PCIE_AUX_CLK>; 369 assigned-clock-rates = <19200000>; 370 371 iommu-map = <0x0 &apps_smmu 0x0200 0x1>, 372 <0x100 &apps_smmu 0x0201 0x1>, 373 <0x200 &apps_smmu 0x0202 0x1>, 374 <0x300 &apps_smmu 0x0203 0x1>, 375 <0x400 &apps_smmu 0x0204 0x1>; 376 377 resets = <&gcc GCC_PCIE_BCR>; 378 reset-names = "pci"; 379 380 power-domains = <&gcc PCIE_GDSC>; 381 382 phys = <&pcie_lane>; 383 phy-names = "pciephy"; 384 385 status = "disabled"; 386 }; 387 388 pcie_ep: pcie-ep@1c00000 { 389 compatible = "qcom,sdx55-pcie-ep"; 390 reg = <0x01c00000 0x3000>, 391 <0x40000000 0xf1d>, 392 <0x40000f20 0xc8>, 393 <0x40001000 0x1000>, 394 <0x40200000 0x100000>, 395 <0x01c03000 0x3000>; 396 reg-names = "parf", 397 "dbi", 398 "elbi", 399 "atu", 400 "addr_space", 401 "mmio"; 402 403 qcom,perst-regs = <&tcsr 0xb258 0xb270>; 404 405 clocks = <&gcc GCC_PCIE_AUX_CLK>, 406 <&gcc GCC_PCIE_CFG_AHB_CLK>, 407 <&gcc GCC_PCIE_MSTR_AXI_CLK>, 408 <&gcc GCC_PCIE_SLV_AXI_CLK>, 409 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>, 410 <&gcc GCC_PCIE_SLEEP_CLK>, 411 <&gcc GCC_PCIE_0_CLKREF_CLK>; 412 clock-names = "aux", 413 "cfg", 414 "bus_master", 415 "bus_slave", 416 "slave_q2a", 417 "sleep", 418 "ref"; 419 420 interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, 421 <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>; 422 interrupt-names = "global", 423 "doorbell"; 424 425 interconnects = <&system_noc MASTER_PCIE &mc_virt SLAVE_EBI_CH0>; 426 interconnect-names = "pcie-mem"; 427 428 resets = <&gcc GCC_PCIE_BCR>; 429 reset-names = "core"; 430 power-domains = <&gcc PCIE_GDSC>; 431 phys = <&pcie_lane>; 432 phy-names = "pciephy"; 433 max-link-speed = <3>; 434 num-lanes = <2>; 435 436 status = "disabled"; 437 }; 438 439 pcie_phy: phy@1c07000 { 440 compatible = "qcom,sdx55-qmp-pcie-phy"; 441 reg = <0x01c07000 0x1c4>; 442 #address-cells = <1>; 443 #size-cells = <1>; 444 ranges; 445 clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>, 446 <&gcc GCC_PCIE_CFG_AHB_CLK>, 447 <&gcc GCC_PCIE_0_CLKREF_CLK>, 448 <&gcc GCC_PCIE_RCHNG_PHY_CLK>; 449 clock-names = "aux", 450 "cfg_ahb", 451 "ref", 452 "refgen"; 453 454 resets = <&gcc GCC_PCIE_PHY_BCR>; 455 reset-names = "phy"; 456 457 assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>; 458 assigned-clock-rates = <100000000>; 459 460 status = "disabled"; 461 462 pcie_lane: lanes@1c06000 { 463 reg = <0x01c06000 0x104>, /* tx0 */ 464 <0x01c06200 0x328>, /* rx0 */ 465 <0x01c07200 0x1e8>, /* pcs */ 466 <0x01c06800 0x104>, /* tx1 */ 467 <0x01c06a00 0x328>, /* rx1 */ 468 <0x01c07600 0x800>; /* pcs_misc */ 469 clocks = <&gcc GCC_PCIE_PIPE_CLK>; 470 clock-names = "pipe0"; 471 472 #phy-cells = <0>; 473 clock-output-names = "pcie_pipe_clk"; 474 }; 475 }; 476 477 ipa: ipa@1e40000 { 478 compatible = "qcom,sdx55-ipa"; 479 480 iommus = <&apps_smmu 0x5e0 0x0>, 481 <&apps_smmu 0x5e2 0x0>; 482 reg = <0x1e40000 0x7000>, 483 <0x1e50000 0x4b20>, 484 <0x1e04000 0x2c000>; 485 reg-names = "ipa-reg", 486 "ipa-shared", 487 "gsi"; 488 489 interrupts-extended = <&intc GIC_SPI 241 IRQ_TYPE_EDGE_RISING>, 490 <&intc GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, 491 <&ipa_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, 492 <&ipa_smp2p_in 1 IRQ_TYPE_EDGE_RISING>; 493 interrupt-names = "ipa", 494 "gsi", 495 "ipa-clock-query", 496 "ipa-setup-ready"; 497 498 clocks = <&rpmhcc RPMH_IPA_CLK>; 499 clock-names = "core"; 500 501 interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>, 502 <&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>, 503 <&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>; 504 interconnect-names = "memory", 505 "imem", 506 "config"; 507 508 qcom,smem-states = <&ipa_smp2p_out 0>, 509 <&ipa_smp2p_out 1>; 510 qcom,smem-state-names = "ipa-clock-enabled-valid", 511 "ipa-clock-enabled"; 512 513 status = "disabled"; 514 }; 515 516 tcsr_mutex: hwlock@1f40000 { 517 compatible = "qcom,tcsr-mutex"; 518 reg = <0x01f40000 0x40000>; 519 #hwlock-cells = <1>; 520 }; 521 522 tcsr: syscon@1fc0000 { 523 compatible = "qcom,sdx55-tcsr", "syscon"; 524 reg = <0x01fc0000 0x1000>; 525 }; 526 527 sdhc_1: mmc@8804000 { 528 compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5"; 529 reg = <0x08804000 0x1000>; 530 interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>, 531 <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; 532 interrupt-names = "hc_irq", "pwr_irq"; 533 clocks = <&gcc GCC_SDCC1_AHB_CLK>, 534 <&gcc GCC_SDCC1_APPS_CLK>; 535 clock-names = "iface", "core"; 536 status = "disabled"; 537 }; 538 539 remoteproc_mpss: remoteproc@4080000 { 540 compatible = "qcom,sdx55-mpss-pas"; 541 reg = <0x04080000 0x4040>; 542 543 interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>, 544 <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, 545 <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, 546 <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, 547 <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>, 548 <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>; 549 interrupt-names = "wdog", "fatal", "ready", "handover", 550 "stop-ack", "shutdown-ack"; 551 552 clocks = <&rpmhcc RPMH_CXO_CLK>; 553 clock-names = "xo"; 554 555 power-domains = <&rpmhpd SDX55_CX>, 556 <&rpmhpd SDX55_MSS>; 557 power-domain-names = "cx", "mss"; 558 559 qcom,smem-states = <&modem_smp2p_out 0>; 560 qcom,smem-state-names = "stop"; 561 562 status = "disabled"; 563 564 glink-edge { 565 interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>; 566 label = "mpss"; 567 qcom,remote-pid = <1>; 568 mboxes = <&apcs 15>; 569 }; 570 }; 571 572 usb: usb@a6f8800 { 573 compatible = "qcom,sdx55-dwc3", "qcom,dwc3"; 574 reg = <0x0a6f8800 0x400>; 575 status = "disabled"; 576 #address-cells = <1>; 577 #size-cells = <1>; 578 ranges; 579 580 clocks = <&gcc GCC_USB30_SLV_AHB_CLK>, 581 <&gcc GCC_USB30_MASTER_CLK>, 582 <&gcc GCC_USB30_MSTR_AXI_CLK>, 583 <&gcc GCC_USB30_SLEEP_CLK>, 584 <&gcc GCC_USB30_MOCK_UTMI_CLK>; 585 clock-names = "cfg_noc", 586 "core", 587 "iface", 588 "sleep", 589 "mock_utmi"; 590 591 assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>, 592 <&gcc GCC_USB30_MASTER_CLK>; 593 assigned-clock-rates = <19200000>, <200000000>; 594 595 interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, 596 <&pdc 51 IRQ_TYPE_LEVEL_HIGH>, 597 <&pdc 11 IRQ_TYPE_EDGE_BOTH>, 598 <&pdc 10 IRQ_TYPE_EDGE_BOTH>; 599 interrupt-names = "hs_phy_irq", "ss_phy_irq", 600 "dm_hs_phy_irq", "dp_hs_phy_irq"; 601 602 power-domains = <&gcc USB30_GDSC>; 603 604 resets = <&gcc GCC_USB30_BCR>; 605 606 usb_dwc3: usb@a600000 { 607 compatible = "snps,dwc3"; 608 reg = <0x0a600000 0xcd00>; 609 interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; 610 iommus = <&apps_smmu 0x1a0 0x0>; 611 snps,dis_u2_susphy_quirk; 612 snps,dis_enblslpm_quirk; 613 phys = <&usb_hsphy>, <&usb_ssphy>; 614 phy-names = "usb2-phy", "usb3-phy"; 615 }; 616 }; 617 618 pdc: interrupt-controller@b210000 { 619 compatible = "qcom,sdx55-pdc", "qcom,pdc"; 620 reg = <0x0b210000 0x30000>; 621 qcom,pdc-ranges = <0 179 52>; 622 #interrupt-cells = <2>; 623 interrupt-parent = <&intc>; 624 interrupt-controller; 625 }; 626 627 restart@c264000 { 628 compatible = "qcom,pshold"; 629 reg = <0x0c264000 0x1000>; 630 }; 631 632 spmi_bus: spmi@c440000 { 633 compatible = "qcom,spmi-pmic-arb"; 634 reg = <0x0c440000 0x0000d00>, 635 <0x0c600000 0x2000000>, 636 <0x0e600000 0x0100000>, 637 <0x0e700000 0x00a0000>, 638 <0x0c40a000 0x0000700>; 639 reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; 640 interrupt-names = "periph_irq"; 641 interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; 642 qcom,ee = <0>; 643 qcom,channel = <0>; 644 #address-cells = <2>; 645 #size-cells = <0>; 646 interrupt-controller; 647 #interrupt-cells = <4>; 648 cell-index = <0>; 649 }; 650 651 tlmm: pinctrl@f100000 { 652 compatible = "qcom,sdx55-pinctrl"; 653 reg = <0xf100000 0x300000>; 654 interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>; 655 gpio-controller; 656 #gpio-cells = <2>; 657 interrupt-controller; 658 #interrupt-cells = <2>; 659 gpio-ranges = <&tlmm 0 0 108>; 660 }; 661 662 sram@1468f000 { 663 compatible = "qcom,sdx55-imem", "syscon", "simple-mfd"; 664 reg = <0x1468f000 0x1000>; 665 666 #address-cells = <1>; 667 #size-cells = <1>; 668 669 ranges = <0x0 0x1468f000 0x1000>; 670 671 pil-reloc@94c { 672 compatible = "qcom,pil-reloc-info"; 673 reg = <0x94c 0x200>; 674 }; 675 }; 676 677 apps_smmu: iommu@15000000 { 678 compatible = "qcom,sdx55-smmu-500", "qcom,smmu-500", "arm,mmu-500"; 679 reg = <0x15000000 0x20000>; 680 #iommu-cells = <2>; 681 #global-interrupts = <1>; 682 interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, 683 <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, 684 <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>, 685 <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, 686 <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>, 687 <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, 688 <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, 689 <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, 690 <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, 691 <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, 692 <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, 693 <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, 694 <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, 695 <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, 696 <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, 697 <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, 698 <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; 699 }; 700 701 intc: interrupt-controller@17800000 { 702 compatible = "qcom,msm-qgic2"; 703 interrupt-controller; 704 interrupt-parent = <&intc>; 705 #interrupt-cells = <3>; 706 reg = <0x17800000 0x1000>, 707 <0x17802000 0x1000>; 708 }; 709 710 a7pll: clock@17808000 { 711 compatible = "qcom,sdx55-a7pll"; 712 reg = <0x17808000 0x1000>; 713 clocks = <&rpmhcc RPMH_CXO_CLK>; 714 clock-names = "bi_tcxo"; 715 #clock-cells = <0>; 716 }; 717 718 apcs: mailbox@17810000 { 719 compatible = "qcom,sdx55-apcs-gcc", "syscon"; 720 reg = <0x17810000 0x2000>; 721 #mbox-cells = <1>; 722 clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>; 723 clock-names = "ref", "pll", "aux"; 724 #clock-cells = <0>; 725 }; 726 727 watchdog@17817000 { 728 compatible = "qcom,apss-wdt-sdx55", "qcom,kpss-wdt"; 729 reg = <0x17817000 0x1000>; 730 clocks = <&sleep_clk>; 731 }; 732 733 timer@17820000 { 734 #address-cells = <1>; 735 #size-cells = <1>; 736 ranges; 737 compatible = "arm,armv7-timer-mem"; 738 reg = <0x17820000 0x1000>; 739 clock-frequency = <19200000>; 740 741 frame@17821000 { 742 frame-number = <0>; 743 interrupts = <GIC_SPI 7 0x4>, 744 <GIC_SPI 6 0x4>; 745 reg = <0x17821000 0x1000>, 746 <0x17822000 0x1000>; 747 }; 748 749 frame@17823000 { 750 frame-number = <1>; 751 interrupts = <GIC_SPI 8 0x4>; 752 reg = <0x17823000 0x1000>; 753 status = "disabled"; 754 }; 755 756 frame@17824000 { 757 frame-number = <2>; 758 interrupts = <GIC_SPI 9 0x4>; 759 reg = <0x17824000 0x1000>; 760 status = "disabled"; 761 }; 762 763 frame@17825000 { 764 frame-number = <3>; 765 interrupts = <GIC_SPI 10 0x4>; 766 reg = <0x17825000 0x1000>; 767 status = "disabled"; 768 }; 769 770 frame@17826000 { 771 frame-number = <4>; 772 interrupts = <GIC_SPI 11 0x4>; 773 reg = <0x17826000 0x1000>; 774 status = "disabled"; 775 }; 776 777 frame@17827000 { 778 frame-number = <5>; 779 interrupts = <GIC_SPI 12 0x4>; 780 reg = <0x17827000 0x1000>; 781 status = "disabled"; 782 }; 783 784 frame@17828000 { 785 frame-number = <6>; 786 interrupts = <GIC_SPI 13 0x4>; 787 reg = <0x17828000 0x1000>; 788 status = "disabled"; 789 }; 790 791 frame@17829000 { 792 frame-number = <7>; 793 interrupts = <GIC_SPI 14 0x4>; 794 reg = <0x17829000 0x1000>; 795 status = "disabled"; 796 }; 797 }; 798 799 apps_rsc: rsc@17830000 { 800 compatible = "qcom,rpmh-rsc"; 801 reg = <0x17830000 0x10000>, <0x17840000 0x10000>; 802 reg-names = "drv-0", "drv-1"; 803 interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>, 804 <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; 805 qcom,tcs-offset = <0xd00>; 806 qcom,drv-id = <1>; 807 qcom,tcs-config = <ACTIVE_TCS 2>, <SLEEP_TCS 2>, 808 <WAKE_TCS 2>, <CONTROL_TCS 1>; 809 810 rpmhcc: clock-controller { 811 compatible = "qcom,sdx55-rpmh-clk"; 812 #clock-cells = <1>; 813 clock-names = "xo"; 814 clocks = <&xo_board>; 815 }; 816 817 rpmhpd: power-controller { 818 compatible = "qcom,sdx55-rpmhpd"; 819 #power-domain-cells = <1>; 820 operating-points-v2 = <&rpmhpd_opp_table>; 821 822 rpmhpd_opp_table: opp-table { 823 compatible = "operating-points-v2"; 824 825 rpmhpd_opp_ret: opp1 { 826 opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>; 827 }; 828 829 rpmhpd_opp_min_svs: opp2 { 830 opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>; 831 }; 832 833 rpmhpd_opp_low_svs: opp3 { 834 opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>; 835 }; 836 837 rpmhpd_opp_svs: opp4 { 838 opp-level = <RPMH_REGULATOR_LEVEL_SVS>; 839 }; 840 841 rpmhpd_opp_svs_l1: opp5 { 842 opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>; 843 }; 844 845 rpmhpd_opp_nom: opp6 { 846 opp-level = <RPMH_REGULATOR_LEVEL_NOM>; 847 }; 848 849 rpmhpd_opp_nom_l1: opp7 { 850 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>; 851 }; 852 853 rpmhpd_opp_nom_l2: opp8 { 854 opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>; 855 }; 856 857 rpmhpd_opp_turbo: opp9 { 858 opp-level = <RPMH_REGULATOR_LEVEL_TURBO>; 859 }; 860 861 rpmhpd_opp_turbo_l1: opp10 { 862 opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>; 863 }; 864 }; 865 }; 866 867 apps_bcm_voter: bcm-voter { 868 compatible = "qcom,bcm-voter"; 869 }; 870 }; 871 }; 872 873 timer { 874 compatible = "arm,armv7-timer"; 875 interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 876 <GIC_PPI 12 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 877 <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, 878 <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; 879 clock-frequency = <19200000>; 880 }; 881}; 882