1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * SCSI low-level driver for the MESH (Macintosh Enhanced SCSI Hardware)
4 * bus adaptor found on Power Macintosh computers.
5 * We assume the MESH is connected to a DBDMA (descriptor-based DMA)
6 * controller.
7 *
8 * Paul Mackerras, August 1996.
9 * Copyright (C) 1996 Paul Mackerras.
10 *
11 * Apr. 21 2002 - BenH Rework bus reset code for new error handler
12 * Add delay after initial bus reset
13 * Add module parameters
14 *
15 * Sep. 27 2003 - BenH Move to new driver model, fix some write posting
16 * issues
17 * To do:
18 * - handle aborts correctly
19 * - retry arbitration if lost (unless higher levels do this for us)
20 * - power down the chip when no device is detected
21 */
22 #include <linux/module.h>
23 #include <linux/kernel.h>
24 #include <linux/delay.h>
25 #include <linux/types.h>
26 #include <linux/string.h>
27 #include <linux/blkdev.h>
28 #include <linux/proc_fs.h>
29 #include <linux/stat.h>
30 #include <linux/interrupt.h>
31 #include <linux/reboot.h>
32 #include <linux/spinlock.h>
33 #include <linux/pci.h>
34 #include <linux/pgtable.h>
35 #include <asm/dbdma.h>
36 #include <asm/io.h>
37 #include <asm/prom.h>
38 #include <asm/irq.h>
39 #include <asm/hydra.h>
40 #include <asm/processor.h>
41 #include <asm/setup.h>
42 #include <asm/pmac_feature.h>
43 #include <asm/macio.h>
44
45 #include <scsi/scsi.h>
46 #include <scsi/scsi_cmnd.h>
47 #include <scsi/scsi_device.h>
48 #include <scsi/scsi_host.h>
49
50 #include "mesh.h"
51
52 #if 1
53 #undef KERN_DEBUG
54 #define KERN_DEBUG KERN_WARNING
55 #endif
56
57 MODULE_AUTHOR("Paul Mackerras (paulus@samba.org)");
58 MODULE_DESCRIPTION("PowerMac MESH SCSI driver");
59 MODULE_LICENSE("GPL");
60
61 static int sync_rate = CONFIG_SCSI_MESH_SYNC_RATE;
62 static int sync_targets = 0xff;
63 static int resel_targets = 0xff;
64 static int debug_targets = 0; /* print debug for these targets */
65 static int init_reset_delay = CONFIG_SCSI_MESH_RESET_DELAY_MS;
66
67 module_param(sync_rate, int, 0);
68 MODULE_PARM_DESC(sync_rate, "Synchronous rate (0..10, 0=async)");
69 module_param(sync_targets, int, 0);
70 MODULE_PARM_DESC(sync_targets, "Bitmask of targets allowed to set synchronous");
71 module_param(resel_targets, int, 0);
72 MODULE_PARM_DESC(resel_targets, "Bitmask of targets allowed to set disconnect");
73 module_param(debug_targets, int, 0644);
74 MODULE_PARM_DESC(debug_targets, "Bitmask of debugged targets");
75 module_param(init_reset_delay, int, 0);
76 MODULE_PARM_DESC(init_reset_delay, "Initial bus reset delay (0=no reset)");
77
78 static int mesh_sync_period = 100;
79 static int mesh_sync_offset = 0;
80 static unsigned char use_active_neg = 0; /* bit mask for SEQ_ACTIVE_NEG if used */
81
82 #define ALLOW_SYNC(tgt) ((sync_targets >> (tgt)) & 1)
83 #define ALLOW_RESEL(tgt) ((resel_targets >> (tgt)) & 1)
84 #define ALLOW_DEBUG(tgt) ((debug_targets >> (tgt)) & 1)
85 #define DEBUG_TARGET(cmd) ((cmd) && ALLOW_DEBUG((cmd)->device->id))
86
87 #undef MESH_DBG
88 #define N_DBG_LOG 50
89 #define N_DBG_SLOG 20
90 #define NUM_DBG_EVENTS 13
91 #undef DBG_USE_TB /* bombs on 601 */
92
93 struct dbglog {
94 char *fmt;
95 u32 tb;
96 u8 phase;
97 u8 bs0;
98 u8 bs1;
99 u8 tgt;
100 int d;
101 };
102
103 enum mesh_phase {
104 idle,
105 arbitrating,
106 selecting,
107 commanding,
108 dataing,
109 statusing,
110 busfreeing,
111 disconnecting,
112 reselecting,
113 sleeping
114 };
115
116 enum msg_phase {
117 msg_none,
118 msg_out,
119 msg_out_xxx,
120 msg_out_last,
121 msg_in,
122 msg_in_bad,
123 };
124
125 enum sdtr_phase {
126 do_sdtr,
127 sdtr_sent,
128 sdtr_done
129 };
130
131 struct mesh_target {
132 enum sdtr_phase sdtr_state;
133 int sync_params;
134 int data_goes_out; /* guess as to data direction */
135 struct scsi_cmnd *current_req;
136 u32 saved_ptr;
137 #ifdef MESH_DBG
138 int log_ix;
139 int n_log;
140 struct dbglog log[N_DBG_LOG];
141 #endif
142 };
143
144 struct mesh_state {
145 volatile struct mesh_regs __iomem *mesh;
146 int meshintr;
147 volatile struct dbdma_regs __iomem *dma;
148 int dmaintr;
149 struct Scsi_Host *host;
150 struct mesh_state *next;
151 struct scsi_cmnd *request_q;
152 struct scsi_cmnd *request_qtail;
153 enum mesh_phase phase; /* what we're currently trying to do */
154 enum msg_phase msgphase;
155 int conn_tgt; /* target we're connected to */
156 struct scsi_cmnd *current_req; /* req we're currently working on */
157 int data_ptr;
158 int dma_started;
159 int dma_count;
160 int stat;
161 int aborting;
162 int expect_reply;
163 int n_msgin;
164 u8 msgin[16];
165 int n_msgout;
166 int last_n_msgout;
167 u8 msgout[16];
168 struct dbdma_cmd *dma_cmds; /* space for dbdma commands, aligned */
169 dma_addr_t dma_cmd_bus;
170 void *dma_cmd_space;
171 int dma_cmd_size;
172 int clk_freq;
173 struct mesh_target tgts[8];
174 struct macio_dev *mdev;
175 struct pci_dev* pdev;
176 #ifdef MESH_DBG
177 int log_ix;
178 int n_log;
179 struct dbglog log[N_DBG_SLOG];
180 #endif
181 };
182
183 /*
184 * Driver is too messy, we need a few prototypes...
185 */
186 static void mesh_done(struct mesh_state *ms, int start_next);
187 static void mesh_interrupt(struct mesh_state *ms);
188 static void cmd_complete(struct mesh_state *ms);
189 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd);
190 static void halt_dma(struct mesh_state *ms);
191 static void phase_mismatch(struct mesh_state *ms);
192
193
194 /*
195 * Some debugging & logging routines
196 */
197
198 #ifdef MESH_DBG
199
readtb(void)200 static inline u32 readtb(void)
201 {
202 u32 tb;
203
204 #ifdef DBG_USE_TB
205 /* Beware: if you enable this, it will crash on 601s. */
206 asm ("mftb %0" : "=r" (tb) : );
207 #else
208 tb = 0;
209 #endif
210 return tb;
211 }
212
dlog(struct mesh_state * ms,char * fmt,int a)213 static void dlog(struct mesh_state *ms, char *fmt, int a)
214 {
215 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
216 struct dbglog *tlp, *slp;
217
218 tlp = &tp->log[tp->log_ix];
219 slp = &ms->log[ms->log_ix];
220 tlp->fmt = fmt;
221 tlp->tb = readtb();
222 tlp->phase = (ms->msgphase << 4) + ms->phase;
223 tlp->bs0 = ms->mesh->bus_status0;
224 tlp->bs1 = ms->mesh->bus_status1;
225 tlp->tgt = ms->conn_tgt;
226 tlp->d = a;
227 *slp = *tlp;
228 if (++tp->log_ix >= N_DBG_LOG)
229 tp->log_ix = 0;
230 if (tp->n_log < N_DBG_LOG)
231 ++tp->n_log;
232 if (++ms->log_ix >= N_DBG_SLOG)
233 ms->log_ix = 0;
234 if (ms->n_log < N_DBG_SLOG)
235 ++ms->n_log;
236 }
237
dumplog(struct mesh_state * ms,int t)238 static void dumplog(struct mesh_state *ms, int t)
239 {
240 struct mesh_target *tp = &ms->tgts[t];
241 struct dbglog *lp;
242 int i;
243
244 if (tp->n_log == 0)
245 return;
246 i = tp->log_ix - tp->n_log;
247 if (i < 0)
248 i += N_DBG_LOG;
249 tp->n_log = 0;
250 do {
251 lp = &tp->log[i];
252 printk(KERN_DEBUG "mesh log %d: bs=%.2x%.2x ph=%.2x ",
253 t, lp->bs1, lp->bs0, lp->phase);
254 #ifdef DBG_USE_TB
255 printk("tb=%10u ", lp->tb);
256 #endif
257 printk(lp->fmt, lp->d);
258 printk("\n");
259 if (++i >= N_DBG_LOG)
260 i = 0;
261 } while (i != tp->log_ix);
262 }
263
dumpslog(struct mesh_state * ms)264 static void dumpslog(struct mesh_state *ms)
265 {
266 struct dbglog *lp;
267 int i;
268
269 if (ms->n_log == 0)
270 return;
271 i = ms->log_ix - ms->n_log;
272 if (i < 0)
273 i += N_DBG_SLOG;
274 ms->n_log = 0;
275 do {
276 lp = &ms->log[i];
277 printk(KERN_DEBUG "mesh log: bs=%.2x%.2x ph=%.2x t%d ",
278 lp->bs1, lp->bs0, lp->phase, lp->tgt);
279 #ifdef DBG_USE_TB
280 printk("tb=%10u ", lp->tb);
281 #endif
282 printk(lp->fmt, lp->d);
283 printk("\n");
284 if (++i >= N_DBG_SLOG)
285 i = 0;
286 } while (i != ms->log_ix);
287 }
288
289 #else
290
dlog(struct mesh_state * ms,char * fmt,int a)291 static inline void dlog(struct mesh_state *ms, char *fmt, int a)
292 {}
dumplog(struct mesh_state * ms,int tgt)293 static inline void dumplog(struct mesh_state *ms, int tgt)
294 {}
dumpslog(struct mesh_state * ms)295 static inline void dumpslog(struct mesh_state *ms)
296 {}
297
298 #endif /* MESH_DBG */
299
300 #define MKWORD(a, b, c, d) (((a) << 24) + ((b) << 16) + ((c) << 8) + (d))
301
302 static void
mesh_dump_regs(struct mesh_state * ms)303 mesh_dump_regs(struct mesh_state *ms)
304 {
305 volatile struct mesh_regs __iomem *mr = ms->mesh;
306 volatile struct dbdma_regs __iomem *md = ms->dma;
307 int t;
308 struct mesh_target *tp;
309
310 printk(KERN_DEBUG "mesh: state at %p, regs at %p, dma at %p\n",
311 ms, mr, md);
312 printk(KERN_DEBUG " ct=%4x seq=%2x bs=%4x fc=%2x "
313 "exc=%2x err=%2x im=%2x int=%2x sp=%2x\n",
314 (mr->count_hi << 8) + mr->count_lo, mr->sequence,
315 (mr->bus_status1 << 8) + mr->bus_status0, mr->fifo_count,
316 mr->exception, mr->error, mr->intr_mask, mr->interrupt,
317 mr->sync_params);
318 while(in_8(&mr->fifo_count))
319 printk(KERN_DEBUG " fifo data=%.2x\n",in_8(&mr->fifo));
320 printk(KERN_DEBUG " dma stat=%x cmdptr=%x\n",
321 in_le32(&md->status), in_le32(&md->cmdptr));
322 printk(KERN_DEBUG " phase=%d msgphase=%d conn_tgt=%d data_ptr=%d\n",
323 ms->phase, ms->msgphase, ms->conn_tgt, ms->data_ptr);
324 printk(KERN_DEBUG " dma_st=%d dma_ct=%d n_msgout=%d\n",
325 ms->dma_started, ms->dma_count, ms->n_msgout);
326 for (t = 0; t < 8; ++t) {
327 tp = &ms->tgts[t];
328 if (tp->current_req == NULL)
329 continue;
330 printk(KERN_DEBUG " target %d: req=%p goes_out=%d saved_ptr=%d\n",
331 t, tp->current_req, tp->data_goes_out, tp->saved_ptr);
332 }
333 }
334
335
336 /*
337 * Flush write buffers on the bus path to the mesh
338 */
mesh_flush_io(volatile struct mesh_regs __iomem * mr)339 static inline void mesh_flush_io(volatile struct mesh_regs __iomem *mr)
340 {
341 (void)in_8(&mr->mesh_id);
342 }
343
344
345 /* Called with meshinterrupt disabled, initialize the chipset
346 * and eventually do the initial bus reset. The lock must not be
347 * held since we can schedule.
348 */
mesh_init(struct mesh_state * ms)349 static void mesh_init(struct mesh_state *ms)
350 {
351 volatile struct mesh_regs __iomem *mr = ms->mesh;
352 volatile struct dbdma_regs __iomem *md = ms->dma;
353
354 mesh_flush_io(mr);
355 udelay(100);
356
357 /* Reset controller */
358 out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16); /* stop dma */
359 out_8(&mr->exception, 0xff); /* clear all exception bits */
360 out_8(&mr->error, 0xff); /* clear all error bits */
361 out_8(&mr->sequence, SEQ_RESETMESH);
362 mesh_flush_io(mr);
363 udelay(10);
364 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
365 out_8(&mr->source_id, ms->host->this_id);
366 out_8(&mr->sel_timeout, 25); /* 250ms */
367 out_8(&mr->sync_params, ASYNC_PARAMS);
368
369 if (init_reset_delay) {
370 printk(KERN_INFO "mesh: performing initial bus reset...\n");
371
372 /* Reset bus */
373 out_8(&mr->bus_status1, BS1_RST); /* assert RST */
374 mesh_flush_io(mr);
375 udelay(30); /* leave it on for >= 25us */
376 out_8(&mr->bus_status1, 0); /* negate RST */
377 mesh_flush_io(mr);
378
379 /* Wait for bus to come back */
380 msleep(init_reset_delay);
381 }
382
383 /* Reconfigure controller */
384 out_8(&mr->interrupt, 0xff); /* clear all interrupt bits */
385 out_8(&mr->sequence, SEQ_FLUSHFIFO);
386 mesh_flush_io(mr);
387 udelay(1);
388 out_8(&mr->sync_params, ASYNC_PARAMS);
389 out_8(&mr->sequence, SEQ_ENBRESEL);
390
391 ms->phase = idle;
392 ms->msgphase = msg_none;
393 }
394
395
mesh_start_cmd(struct mesh_state * ms,struct scsi_cmnd * cmd)396 static void mesh_start_cmd(struct mesh_state *ms, struct scsi_cmnd *cmd)
397 {
398 volatile struct mesh_regs __iomem *mr = ms->mesh;
399 int t, id;
400
401 id = cmd->device->id;
402 ms->current_req = cmd;
403 ms->tgts[id].data_goes_out = cmd->sc_data_direction == DMA_TO_DEVICE;
404 ms->tgts[id].current_req = cmd;
405
406 #if 1
407 if (DEBUG_TARGET(cmd)) {
408 int i;
409 printk(KERN_DEBUG "mesh_start: %p tgt=%d cmd=", cmd, id);
410 for (i = 0; i < cmd->cmd_len; ++i)
411 printk(" %x", cmd->cmnd[i]);
412 printk(" use_sg=%d buffer=%p bufflen=%u\n",
413 scsi_sg_count(cmd), scsi_sglist(cmd), scsi_bufflen(cmd));
414 }
415 #endif
416 if (ms->dma_started)
417 panic("mesh: double DMA start !\n");
418
419 ms->phase = arbitrating;
420 ms->msgphase = msg_none;
421 ms->data_ptr = 0;
422 ms->dma_started = 0;
423 ms->n_msgout = 0;
424 ms->last_n_msgout = 0;
425 ms->expect_reply = 0;
426 ms->conn_tgt = id;
427 ms->tgts[id].saved_ptr = 0;
428 ms->stat = DID_OK;
429 ms->aborting = 0;
430 #ifdef MESH_DBG
431 ms->tgts[id].n_log = 0;
432 dlog(ms, "start cmd=%x", (int) cmd);
433 #endif
434
435 /* Off we go */
436 dlog(ms, "about to arb, intr/exc/err/fc=%.8x",
437 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
438 out_8(&mr->interrupt, INT_CMDDONE);
439 out_8(&mr->sequence, SEQ_ENBRESEL);
440 mesh_flush_io(mr);
441 udelay(1);
442
443 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
444 /*
445 * Some other device has the bus or is arbitrating for it -
446 * probably a target which is about to reselect us.
447 */
448 dlog(ms, "busy b4 arb, intr/exc/err/fc=%.8x",
449 MKWORD(mr->interrupt, mr->exception,
450 mr->error, mr->fifo_count));
451 for (t = 100; t > 0; --t) {
452 if ((in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) == 0)
453 break;
454 if (in_8(&mr->interrupt) != 0) {
455 dlog(ms, "intr b4 arb, intr/exc/err/fc=%.8x",
456 MKWORD(mr->interrupt, mr->exception,
457 mr->error, mr->fifo_count));
458 mesh_interrupt(ms);
459 if (ms->phase != arbitrating)
460 return;
461 }
462 udelay(1);
463 }
464 if (in_8(&mr->bus_status1) & (BS1_BSY | BS1_SEL)) {
465 /* XXX should try again in a little while */
466 ms->stat = DID_BUS_BUSY;
467 ms->phase = idle;
468 mesh_done(ms, 0);
469 return;
470 }
471 }
472
473 /*
474 * Apparently the mesh has a bug where it will assert both its
475 * own bit and the target's bit on the bus during arbitration.
476 */
477 out_8(&mr->dest_id, mr->source_id);
478
479 /*
480 * There appears to be a race with reselection sometimes,
481 * where a target reselects us just as we issue the
482 * arbitrate command. It seems that then the arbitrate
483 * command just hangs waiting for the bus to be free
484 * without giving us a reselection exception.
485 * The only way I have found to get it to respond correctly
486 * is this: disable reselection before issuing the arbitrate
487 * command, then after issuing it, if it looks like a target
488 * is trying to reselect us, reset the mesh and then enable
489 * reselection.
490 */
491 out_8(&mr->sequence, SEQ_DISRESEL);
492 if (in_8(&mr->interrupt) != 0) {
493 dlog(ms, "intr after disresel, intr/exc/err/fc=%.8x",
494 MKWORD(mr->interrupt, mr->exception,
495 mr->error, mr->fifo_count));
496 mesh_interrupt(ms);
497 if (ms->phase != arbitrating)
498 return;
499 dlog(ms, "after intr after disresel, intr/exc/err/fc=%.8x",
500 MKWORD(mr->interrupt, mr->exception,
501 mr->error, mr->fifo_count));
502 }
503
504 out_8(&mr->sequence, SEQ_ARBITRATE);
505
506 for (t = 230; t > 0; --t) {
507 if (in_8(&mr->interrupt) != 0)
508 break;
509 udelay(1);
510 }
511 dlog(ms, "after arb, intr/exc/err/fc=%.8x",
512 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
513 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
514 && (in_8(&mr->bus_status0) & BS0_IO)) {
515 /* looks like a reselection - try resetting the mesh */
516 dlog(ms, "resel? after arb, intr/exc/err/fc=%.8x",
517 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
518 out_8(&mr->sequence, SEQ_RESETMESH);
519 mesh_flush_io(mr);
520 udelay(10);
521 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
522 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
523 out_8(&mr->sequence, SEQ_ENBRESEL);
524 mesh_flush_io(mr);
525 for (t = 10; t > 0 && in_8(&mr->interrupt) == 0; --t)
526 udelay(1);
527 dlog(ms, "tried reset after arb, intr/exc/err/fc=%.8x",
528 MKWORD(mr->interrupt, mr->exception, mr->error, mr->fifo_count));
529 #ifndef MESH_MULTIPLE_HOSTS
530 if (in_8(&mr->interrupt) == 0 && (in_8(&mr->bus_status1) & BS1_SEL)
531 && (in_8(&mr->bus_status0) & BS0_IO)) {
532 printk(KERN_ERR "mesh: controller not responding"
533 " to reselection!\n");
534 /*
535 * If this is a target reselecting us, and the
536 * mesh isn't responding, the higher levels of
537 * the scsi code will eventually time out and
538 * reset the bus.
539 */
540 }
541 #endif
542 }
543 }
544
545 /*
546 * Start the next command for a MESH.
547 * Should be called with interrupts disabled.
548 */
mesh_start(struct mesh_state * ms)549 static void mesh_start(struct mesh_state *ms)
550 {
551 struct scsi_cmnd *cmd, *prev, *next;
552
553 if (ms->phase != idle || ms->current_req != NULL) {
554 printk(KERN_ERR "inappropriate mesh_start (phase=%d, ms=%p)",
555 ms->phase, ms);
556 return;
557 }
558
559 while (ms->phase == idle) {
560 prev = NULL;
561 for (cmd = ms->request_q; ; cmd = (struct scsi_cmnd *) cmd->host_scribble) {
562 if (cmd == NULL)
563 return;
564 if (ms->tgts[cmd->device->id].current_req == NULL)
565 break;
566 prev = cmd;
567 }
568 next = (struct scsi_cmnd *) cmd->host_scribble;
569 if (prev == NULL)
570 ms->request_q = next;
571 else
572 prev->host_scribble = (void *) next;
573 if (next == NULL)
574 ms->request_qtail = prev;
575
576 mesh_start_cmd(ms, cmd);
577 }
578 }
579
mesh_done(struct mesh_state * ms,int start_next)580 static void mesh_done(struct mesh_state *ms, int start_next)
581 {
582 struct scsi_cmnd *cmd;
583 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
584
585 cmd = ms->current_req;
586 ms->current_req = NULL;
587 tp->current_req = NULL;
588 if (cmd) {
589 struct mesh_cmd_priv *mcmd = mesh_priv(cmd);
590
591 set_host_byte(cmd, ms->stat);
592 set_status_byte(cmd, mcmd->status);
593 if (ms->stat == DID_OK)
594 scsi_msg_to_host_byte(cmd, mcmd->message);
595 if (DEBUG_TARGET(cmd)) {
596 printk(KERN_DEBUG "mesh_done: result = %x, data_ptr=%d, buflen=%d\n",
597 cmd->result, ms->data_ptr, scsi_bufflen(cmd));
598 #if 0
599 /* needs to use sg? */
600 if ((cmd->cmnd[0] == 0 || cmd->cmnd[0] == 0x12 || cmd->cmnd[0] == 3)
601 && cmd->request_buffer != 0) {
602 unsigned char *b = cmd->request_buffer;
603 printk(KERN_DEBUG "buffer = %x %x %x %x %x %x %x %x\n",
604 b[0], b[1], b[2], b[3], b[4], b[5], b[6], b[7]);
605 }
606 #endif
607 }
608 mcmd->this_residual -= ms->data_ptr;
609 scsi_done(cmd);
610 }
611 if (start_next) {
612 out_8(&ms->mesh->sequence, SEQ_ENBRESEL);
613 mesh_flush_io(ms->mesh);
614 udelay(1);
615 ms->phase = idle;
616 mesh_start(ms);
617 }
618 }
619
add_sdtr_msg(struct mesh_state * ms)620 static inline void add_sdtr_msg(struct mesh_state *ms)
621 {
622 int i = ms->n_msgout;
623
624 ms->msgout[i] = EXTENDED_MESSAGE;
625 ms->msgout[i+1] = 3;
626 ms->msgout[i+2] = EXTENDED_SDTR;
627 ms->msgout[i+3] = mesh_sync_period/4;
628 ms->msgout[i+4] = (ALLOW_SYNC(ms->conn_tgt)? mesh_sync_offset: 0);
629 ms->n_msgout = i + 5;
630 }
631
set_sdtr(struct mesh_state * ms,int period,int offset)632 static void set_sdtr(struct mesh_state *ms, int period, int offset)
633 {
634 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
635 volatile struct mesh_regs __iomem *mr = ms->mesh;
636 int v, tr;
637
638 tp->sdtr_state = sdtr_done;
639 if (offset == 0) {
640 /* asynchronous */
641 if (SYNC_OFF(tp->sync_params))
642 printk(KERN_INFO "mesh: target %d now asynchronous\n",
643 ms->conn_tgt);
644 tp->sync_params = ASYNC_PARAMS;
645 out_8(&mr->sync_params, ASYNC_PARAMS);
646 return;
647 }
648 /*
649 * We need to compute ceil(clk_freq * period / 500e6) - 2
650 * without incurring overflow.
651 */
652 v = (ms->clk_freq / 5000) * period;
653 if (v <= 250000) {
654 /* special case: sync_period == 5 * clk_period */
655 v = 0;
656 /* units of tr are 100kB/s */
657 tr = (ms->clk_freq + 250000) / 500000;
658 } else {
659 /* sync_period == (v + 2) * 2 * clk_period */
660 v = (v + 99999) / 100000 - 2;
661 if (v > 15)
662 v = 15; /* oops */
663 tr = ((ms->clk_freq / (v + 2)) + 199999) / 200000;
664 }
665 if (offset > 15)
666 offset = 15; /* can't happen */
667 tp->sync_params = SYNC_PARAMS(offset, v);
668 out_8(&mr->sync_params, tp->sync_params);
669 printk(KERN_INFO "mesh: target %d synchronous at %d.%d MB/s\n",
670 ms->conn_tgt, tr/10, tr%10);
671 }
672
start_phase(struct mesh_state * ms)673 static void start_phase(struct mesh_state *ms)
674 {
675 int i, seq, nb;
676 volatile struct mesh_regs __iomem *mr = ms->mesh;
677 volatile struct dbdma_regs __iomem *md = ms->dma;
678 struct scsi_cmnd *cmd = ms->current_req;
679 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
680
681 dlog(ms, "start_phase nmo/exc/fc/seq = %.8x",
682 MKWORD(ms->n_msgout, mr->exception, mr->fifo_count, mr->sequence));
683 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
684 seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
685 switch (ms->msgphase) {
686 case msg_none:
687 break;
688
689 case msg_in:
690 out_8(&mr->count_hi, 0);
691 out_8(&mr->count_lo, 1);
692 out_8(&mr->sequence, SEQ_MSGIN + seq);
693 ms->n_msgin = 0;
694 return;
695
696 case msg_out:
697 /*
698 * To make sure ATN drops before we assert ACK for
699 * the last byte of the message, we have to do the
700 * last byte specially.
701 */
702 if (ms->n_msgout <= 0) {
703 printk(KERN_ERR "mesh: msg_out but n_msgout=%d\n",
704 ms->n_msgout);
705 mesh_dump_regs(ms);
706 ms->msgphase = msg_none;
707 break;
708 }
709 if (ALLOW_DEBUG(ms->conn_tgt)) {
710 printk(KERN_DEBUG "mesh: sending %d msg bytes:",
711 ms->n_msgout);
712 for (i = 0; i < ms->n_msgout; ++i)
713 printk(" %x", ms->msgout[i]);
714 printk("\n");
715 }
716 dlog(ms, "msgout msg=%.8x", MKWORD(ms->n_msgout, ms->msgout[0],
717 ms->msgout[1], ms->msgout[2]));
718 out_8(&mr->count_hi, 0);
719 out_8(&mr->sequence, SEQ_FLUSHFIFO);
720 mesh_flush_io(mr);
721 udelay(1);
722 /*
723 * If ATN is not already asserted, we assert it, then
724 * issue a SEQ_MSGOUT to get the mesh to drop ACK.
725 */
726 if ((in_8(&mr->bus_status0) & BS0_ATN) == 0) {
727 dlog(ms, "bus0 was %.2x explicitly asserting ATN", mr->bus_status0);
728 out_8(&mr->bus_status0, BS0_ATN); /* explicit ATN */
729 mesh_flush_io(mr);
730 udelay(1);
731 out_8(&mr->count_lo, 1);
732 out_8(&mr->sequence, SEQ_MSGOUT + seq);
733 out_8(&mr->bus_status0, 0); /* release explicit ATN */
734 dlog(ms,"hace: after explicit ATN bus0=%.2x",mr->bus_status0);
735 }
736 if (ms->n_msgout == 1) {
737 /*
738 * We can't issue the SEQ_MSGOUT without ATN
739 * until the target has asserted REQ. The logic
740 * in cmd_complete handles both situations:
741 * REQ already asserted or not.
742 */
743 cmd_complete(ms);
744 } else {
745 out_8(&mr->count_lo, ms->n_msgout - 1);
746 out_8(&mr->sequence, SEQ_MSGOUT + seq);
747 for (i = 0; i < ms->n_msgout - 1; ++i)
748 out_8(&mr->fifo, ms->msgout[i]);
749 }
750 return;
751
752 default:
753 printk(KERN_ERR "mesh bug: start_phase msgphase=%d\n",
754 ms->msgphase);
755 }
756
757 switch (ms->phase) {
758 case selecting:
759 out_8(&mr->dest_id, ms->conn_tgt);
760 out_8(&mr->sequence, SEQ_SELECT + SEQ_ATN);
761 break;
762 case commanding:
763 out_8(&mr->sync_params, tp->sync_params);
764 out_8(&mr->count_hi, 0);
765 if (cmd) {
766 out_8(&mr->count_lo, cmd->cmd_len);
767 out_8(&mr->sequence, SEQ_COMMAND + seq);
768 for (i = 0; i < cmd->cmd_len; ++i)
769 out_8(&mr->fifo, cmd->cmnd[i]);
770 } else {
771 out_8(&mr->count_lo, 6);
772 out_8(&mr->sequence, SEQ_COMMAND + seq);
773 for (i = 0; i < 6; ++i)
774 out_8(&mr->fifo, 0);
775 }
776 break;
777 case dataing:
778 /* transfer data, if any */
779 if (!ms->dma_started) {
780 set_dma_cmds(ms, cmd);
781 out_le32(&md->cmdptr, virt_to_phys(ms->dma_cmds));
782 out_le32(&md->control, (RUN << 16) | RUN);
783 ms->dma_started = 1;
784 }
785 nb = ms->dma_count;
786 if (nb > 0xfff0)
787 nb = 0xfff0;
788 ms->dma_count -= nb;
789 ms->data_ptr += nb;
790 out_8(&mr->count_lo, nb);
791 out_8(&mr->count_hi, nb >> 8);
792 out_8(&mr->sequence, (tp->data_goes_out?
793 SEQ_DATAOUT: SEQ_DATAIN) + SEQ_DMA_MODE + seq);
794 break;
795 case statusing:
796 out_8(&mr->count_hi, 0);
797 out_8(&mr->count_lo, 1);
798 out_8(&mr->sequence, SEQ_STATUS + seq);
799 break;
800 case busfreeing:
801 case disconnecting:
802 out_8(&mr->sequence, SEQ_ENBRESEL);
803 mesh_flush_io(mr);
804 udelay(1);
805 dlog(ms, "enbresel intr/exc/err/fc=%.8x",
806 MKWORD(mr->interrupt, mr->exception, mr->error,
807 mr->fifo_count));
808 out_8(&mr->sequence, SEQ_BUSFREE);
809 break;
810 default:
811 printk(KERN_ERR "mesh: start_phase called with phase=%d\n",
812 ms->phase);
813 dumpslog(ms);
814 }
815
816 }
817
get_msgin(struct mesh_state * ms)818 static inline void get_msgin(struct mesh_state *ms)
819 {
820 volatile struct mesh_regs __iomem *mr = ms->mesh;
821 int i, n;
822
823 n = mr->fifo_count;
824 if (n != 0) {
825 i = ms->n_msgin;
826 ms->n_msgin = i + n;
827 for (; n > 0; --n)
828 ms->msgin[i++] = in_8(&mr->fifo);
829 }
830 }
831
msgin_length(struct mesh_state * ms)832 static inline int msgin_length(struct mesh_state *ms)
833 {
834 int b, n;
835
836 n = 1;
837 if (ms->n_msgin > 0) {
838 b = ms->msgin[0];
839 if (b == 1) {
840 /* extended message */
841 n = ms->n_msgin < 2? 2: ms->msgin[1] + 2;
842 } else if (0x20 <= b && b <= 0x2f) {
843 /* 2-byte message */
844 n = 2;
845 }
846 }
847 return n;
848 }
849
reselected(struct mesh_state * ms)850 static void reselected(struct mesh_state *ms)
851 {
852 volatile struct mesh_regs __iomem *mr = ms->mesh;
853 struct scsi_cmnd *cmd;
854 struct mesh_target *tp;
855 int b, t, prev;
856
857 switch (ms->phase) {
858 case idle:
859 break;
860 case arbitrating:
861 if ((cmd = ms->current_req) != NULL) {
862 /* put the command back on the queue */
863 cmd->host_scribble = (void *) ms->request_q;
864 if (ms->request_q == NULL)
865 ms->request_qtail = cmd;
866 ms->request_q = cmd;
867 tp = &ms->tgts[cmd->device->id];
868 tp->current_req = NULL;
869 }
870 break;
871 case busfreeing:
872 ms->phase = reselecting;
873 mesh_done(ms, 0);
874 break;
875 case disconnecting:
876 break;
877 default:
878 printk(KERN_ERR "mesh: reselected in phase %d/%d tgt %d\n",
879 ms->msgphase, ms->phase, ms->conn_tgt);
880 dumplog(ms, ms->conn_tgt);
881 dumpslog(ms);
882 }
883
884 if (ms->dma_started) {
885 printk(KERN_ERR "mesh: reselected with DMA started !\n");
886 halt_dma(ms);
887 }
888 ms->current_req = NULL;
889 ms->phase = dataing;
890 ms->msgphase = msg_in;
891 ms->n_msgout = 0;
892 ms->last_n_msgout = 0;
893 prev = ms->conn_tgt;
894
895 /*
896 * We seem to get abortive reselections sometimes.
897 */
898 while ((in_8(&mr->bus_status1) & BS1_BSY) == 0) {
899 static int mesh_aborted_resels;
900 mesh_aborted_resels++;
901 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
902 mesh_flush_io(mr);
903 udelay(1);
904 out_8(&mr->sequence, SEQ_ENBRESEL);
905 mesh_flush_io(mr);
906 udelay(5);
907 dlog(ms, "extra resel err/exc/fc = %.6x",
908 MKWORD(0, mr->error, mr->exception, mr->fifo_count));
909 }
910 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
911 mesh_flush_io(mr);
912 udelay(1);
913 out_8(&mr->sequence, SEQ_ENBRESEL);
914 mesh_flush_io(mr);
915 udelay(1);
916 out_8(&mr->sync_params, ASYNC_PARAMS);
917
918 /*
919 * Find out who reselected us.
920 */
921 if (in_8(&mr->fifo_count) == 0) {
922 printk(KERN_ERR "mesh: reselection but nothing in fifo?\n");
923 ms->conn_tgt = ms->host->this_id;
924 goto bogus;
925 }
926 /* get the last byte in the fifo */
927 do {
928 b = in_8(&mr->fifo);
929 dlog(ms, "reseldata %x", b);
930 } while (in_8(&mr->fifo_count));
931 for (t = 0; t < 8; ++t)
932 if ((b & (1 << t)) != 0 && t != ms->host->this_id)
933 break;
934 if (b != (1 << t) + (1 << ms->host->this_id)) {
935 printk(KERN_ERR "mesh: bad reselection data %x\n", b);
936 ms->conn_tgt = ms->host->this_id;
937 goto bogus;
938 }
939
940
941 /*
942 * Set up to continue with that target's transfer.
943 */
944 ms->conn_tgt = t;
945 tp = &ms->tgts[t];
946 out_8(&mr->sync_params, tp->sync_params);
947 if (ALLOW_DEBUG(t)) {
948 printk(KERN_DEBUG "mesh: reselected by target %d\n", t);
949 printk(KERN_DEBUG "mesh: saved_ptr=%x goes_out=%d cmd=%p\n",
950 tp->saved_ptr, tp->data_goes_out, tp->current_req);
951 }
952 ms->current_req = tp->current_req;
953 if (tp->current_req == NULL) {
954 printk(KERN_ERR "mesh: reselected by tgt %d but no cmd!\n", t);
955 goto bogus;
956 }
957 ms->data_ptr = tp->saved_ptr;
958 dlog(ms, "resel prev tgt=%d", prev);
959 dlog(ms, "resel err/exc=%.4x", MKWORD(0, 0, mr->error, mr->exception));
960 start_phase(ms);
961 return;
962
963 bogus:
964 dumplog(ms, ms->conn_tgt);
965 dumpslog(ms);
966 ms->data_ptr = 0;
967 ms->aborting = 1;
968 start_phase(ms);
969 }
970
do_abort(struct mesh_state * ms)971 static void do_abort(struct mesh_state *ms)
972 {
973 ms->msgout[0] = ABORT;
974 ms->n_msgout = 1;
975 ms->aborting = 1;
976 ms->stat = DID_ABORT;
977 dlog(ms, "abort", 0);
978 }
979
handle_reset(struct mesh_state * ms)980 static void handle_reset(struct mesh_state *ms)
981 {
982 int tgt;
983 struct mesh_target *tp;
984 struct scsi_cmnd *cmd;
985 volatile struct mesh_regs __iomem *mr = ms->mesh;
986
987 for (tgt = 0; tgt < 8; ++tgt) {
988 tp = &ms->tgts[tgt];
989 if ((cmd = tp->current_req) != NULL) {
990 set_host_byte(cmd, DID_RESET);
991 tp->current_req = NULL;
992 scsi_done(cmd);
993 }
994 ms->tgts[tgt].sdtr_state = do_sdtr;
995 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
996 }
997 ms->current_req = NULL;
998 while ((cmd = ms->request_q) != NULL) {
999 ms->request_q = (struct scsi_cmnd *) cmd->host_scribble;
1000 set_host_byte(cmd, DID_RESET);
1001 scsi_done(cmd);
1002 }
1003 ms->phase = idle;
1004 ms->msgphase = msg_none;
1005 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1006 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1007 mesh_flush_io(mr);
1008 udelay(1);
1009 out_8(&mr->sync_params, ASYNC_PARAMS);
1010 out_8(&mr->sequence, SEQ_ENBRESEL);
1011 }
1012
do_mesh_interrupt(int irq,void * dev_id)1013 static irqreturn_t do_mesh_interrupt(int irq, void *dev_id)
1014 {
1015 unsigned long flags;
1016 struct mesh_state *ms = dev_id;
1017 struct Scsi_Host *dev = ms->host;
1018
1019 spin_lock_irqsave(dev->host_lock, flags);
1020 mesh_interrupt(ms);
1021 spin_unlock_irqrestore(dev->host_lock, flags);
1022 return IRQ_HANDLED;
1023 }
1024
handle_error(struct mesh_state * ms)1025 static void handle_error(struct mesh_state *ms)
1026 {
1027 int err, exc, count;
1028 volatile struct mesh_regs __iomem *mr = ms->mesh;
1029
1030 err = in_8(&mr->error);
1031 exc = in_8(&mr->exception);
1032 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1033 dlog(ms, "error err/exc/fc/cl=%.8x",
1034 MKWORD(err, exc, mr->fifo_count, mr->count_lo));
1035 if (err & ERR_SCSIRESET) {
1036 /* SCSI bus was reset */
1037 printk(KERN_INFO "mesh: SCSI bus reset detected: "
1038 "waiting for end...");
1039 while ((in_8(&mr->bus_status1) & BS1_RST) != 0)
1040 udelay(1);
1041 printk("done\n");
1042 if (ms->dma_started)
1043 halt_dma(ms);
1044 handle_reset(ms);
1045 /* request_q is empty, no point in mesh_start() */
1046 return;
1047 }
1048 if (err & ERR_UNEXPDISC) {
1049 /* Unexpected disconnect */
1050 if (exc & EXC_RESELECTED) {
1051 reselected(ms);
1052 return;
1053 }
1054 if (!ms->aborting) {
1055 printk(KERN_WARNING "mesh: target %d aborted\n",
1056 ms->conn_tgt);
1057 dumplog(ms, ms->conn_tgt);
1058 dumpslog(ms);
1059 }
1060 out_8(&mr->interrupt, INT_CMDDONE);
1061 ms->stat = DID_ABORT;
1062 mesh_done(ms, 1);
1063 return;
1064 }
1065 if (err & ERR_PARITY) {
1066 if (ms->msgphase == msg_in) {
1067 printk(KERN_ERR "mesh: msg parity error, target %d\n",
1068 ms->conn_tgt);
1069 ms->msgout[0] = MSG_PARITY_ERROR;
1070 ms->n_msgout = 1;
1071 ms->msgphase = msg_in_bad;
1072 cmd_complete(ms);
1073 return;
1074 }
1075 if (ms->stat == DID_OK) {
1076 printk(KERN_ERR "mesh: parity error, target %d\n",
1077 ms->conn_tgt);
1078 ms->stat = DID_PARITY;
1079 }
1080 count = (mr->count_hi << 8) + mr->count_lo;
1081 if (count == 0) {
1082 cmd_complete(ms);
1083 } else {
1084 /* reissue the data transfer command */
1085 out_8(&mr->sequence, mr->sequence);
1086 }
1087 return;
1088 }
1089 if (err & ERR_SEQERR) {
1090 if (exc & EXC_RESELECTED) {
1091 /* This can happen if we issue a command to
1092 get the bus just after the target reselects us. */
1093 static int mesh_resel_seqerr;
1094 mesh_resel_seqerr++;
1095 reselected(ms);
1096 return;
1097 }
1098 if (exc == EXC_PHASEMM) {
1099 static int mesh_phasemm_seqerr;
1100 mesh_phasemm_seqerr++;
1101 phase_mismatch(ms);
1102 return;
1103 }
1104 printk(KERN_ERR "mesh: sequence error (err=%x exc=%x)\n",
1105 err, exc);
1106 } else {
1107 printk(KERN_ERR "mesh: unknown error %x (exc=%x)\n", err, exc);
1108 }
1109 mesh_dump_regs(ms);
1110 dumplog(ms, ms->conn_tgt);
1111 if (ms->phase > selecting && (in_8(&mr->bus_status1) & BS1_BSY)) {
1112 /* try to do what the target wants */
1113 do_abort(ms);
1114 phase_mismatch(ms);
1115 return;
1116 }
1117 ms->stat = DID_ERROR;
1118 mesh_done(ms, 1);
1119 }
1120
handle_exception(struct mesh_state * ms)1121 static void handle_exception(struct mesh_state *ms)
1122 {
1123 int exc;
1124 volatile struct mesh_regs __iomem *mr = ms->mesh;
1125
1126 exc = in_8(&mr->exception);
1127 out_8(&mr->interrupt, INT_EXCEPTION | INT_CMDDONE);
1128 if (exc & EXC_RESELECTED) {
1129 static int mesh_resel_exc;
1130 mesh_resel_exc++;
1131 reselected(ms);
1132 } else if (exc == EXC_ARBLOST) {
1133 printk(KERN_DEBUG "mesh: lost arbitration\n");
1134 ms->stat = DID_BUS_BUSY;
1135 mesh_done(ms, 1);
1136 } else if (exc == EXC_SELTO) {
1137 /* selection timed out */
1138 ms->stat = DID_BAD_TARGET;
1139 mesh_done(ms, 1);
1140 } else if (exc == EXC_PHASEMM) {
1141 /* target wants to do something different:
1142 find out what it wants and do it. */
1143 phase_mismatch(ms);
1144 } else {
1145 printk(KERN_ERR "mesh: can't cope with exception %x\n", exc);
1146 mesh_dump_regs(ms);
1147 dumplog(ms, ms->conn_tgt);
1148 do_abort(ms);
1149 phase_mismatch(ms);
1150 }
1151 }
1152
handle_msgin(struct mesh_state * ms)1153 static void handle_msgin(struct mesh_state *ms)
1154 {
1155 int i, code;
1156 struct scsi_cmnd *cmd = ms->current_req;
1157 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1158
1159 if (ms->n_msgin == 0)
1160 return;
1161 code = ms->msgin[0];
1162 if (ALLOW_DEBUG(ms->conn_tgt)) {
1163 printk(KERN_DEBUG "got %d message bytes:", ms->n_msgin);
1164 for (i = 0; i < ms->n_msgin; ++i)
1165 printk(" %x", ms->msgin[i]);
1166 printk("\n");
1167 }
1168 dlog(ms, "msgin msg=%.8x",
1169 MKWORD(ms->n_msgin, code, ms->msgin[1], ms->msgin[2]));
1170
1171 ms->expect_reply = 0;
1172 ms->n_msgout = 0;
1173 if (ms->n_msgin < msgin_length(ms))
1174 goto reject;
1175 if (cmd)
1176 mesh_priv(cmd)->message = code;
1177 switch (code) {
1178 case COMMAND_COMPLETE:
1179 break;
1180 case EXTENDED_MESSAGE:
1181 switch (ms->msgin[2]) {
1182 case EXTENDED_MODIFY_DATA_POINTER:
1183 ms->data_ptr += (ms->msgin[3] << 24) + ms->msgin[6]
1184 + (ms->msgin[4] << 16) + (ms->msgin[5] << 8);
1185 break;
1186 case EXTENDED_SDTR:
1187 if (tp->sdtr_state != sdtr_sent) {
1188 /* reply with an SDTR */
1189 add_sdtr_msg(ms);
1190 /* limit period to at least his value,
1191 offset to no more than his */
1192 if (ms->msgout[3] < ms->msgin[3])
1193 ms->msgout[3] = ms->msgin[3];
1194 if (ms->msgout[4] > ms->msgin[4])
1195 ms->msgout[4] = ms->msgin[4];
1196 set_sdtr(ms, ms->msgout[3], ms->msgout[4]);
1197 ms->msgphase = msg_out;
1198 } else {
1199 set_sdtr(ms, ms->msgin[3], ms->msgin[4]);
1200 }
1201 break;
1202 default:
1203 goto reject;
1204 }
1205 break;
1206 case SAVE_POINTERS:
1207 tp->saved_ptr = ms->data_ptr;
1208 break;
1209 case RESTORE_POINTERS:
1210 ms->data_ptr = tp->saved_ptr;
1211 break;
1212 case DISCONNECT:
1213 ms->phase = disconnecting;
1214 break;
1215 case ABORT:
1216 break;
1217 case MESSAGE_REJECT:
1218 if (tp->sdtr_state == sdtr_sent)
1219 set_sdtr(ms, 0, 0);
1220 break;
1221 case NOP:
1222 break;
1223 default:
1224 if (IDENTIFY_BASE <= code && code <= IDENTIFY_BASE + 7) {
1225 if (cmd == NULL) {
1226 do_abort(ms);
1227 ms->msgphase = msg_out;
1228 } else if (code != cmd->device->lun + IDENTIFY_BASE) {
1229 printk(KERN_WARNING "mesh: lun mismatch "
1230 "(%d != %llu) on reselection from "
1231 "target %d\n", code - IDENTIFY_BASE,
1232 cmd->device->lun, ms->conn_tgt);
1233 }
1234 break;
1235 }
1236 goto reject;
1237 }
1238 return;
1239
1240 reject:
1241 printk(KERN_WARNING "mesh: rejecting message from target %d:",
1242 ms->conn_tgt);
1243 for (i = 0; i < ms->n_msgin; ++i)
1244 printk(" %x", ms->msgin[i]);
1245 printk("\n");
1246 ms->msgout[0] = MESSAGE_REJECT;
1247 ms->n_msgout = 1;
1248 ms->msgphase = msg_out;
1249 }
1250
1251 /*
1252 * Set up DMA commands for transferring data.
1253 */
set_dma_cmds(struct mesh_state * ms,struct scsi_cmnd * cmd)1254 static void set_dma_cmds(struct mesh_state *ms, struct scsi_cmnd *cmd)
1255 {
1256 int i, dma_cmd, total, off, dtot;
1257 struct scatterlist *scl;
1258 struct dbdma_cmd *dcmds;
1259
1260 dma_cmd = ms->tgts[ms->conn_tgt].data_goes_out?
1261 OUTPUT_MORE: INPUT_MORE;
1262 dcmds = ms->dma_cmds;
1263 dtot = 0;
1264 if (cmd) {
1265 int nseg;
1266
1267 mesh_priv(cmd)->this_residual = scsi_bufflen(cmd);
1268
1269 nseg = scsi_dma_map(cmd);
1270 BUG_ON(nseg < 0);
1271
1272 if (nseg) {
1273 total = 0;
1274 off = ms->data_ptr;
1275
1276 scsi_for_each_sg(cmd, scl, nseg, i) {
1277 u32 dma_addr = sg_dma_address(scl);
1278 u32 dma_len = sg_dma_len(scl);
1279
1280 total += scl->length;
1281 if (off >= dma_len) {
1282 off -= dma_len;
1283 continue;
1284 }
1285 if (dma_len > 0xffff)
1286 panic("mesh: scatterlist element >= 64k");
1287 dcmds->req_count = cpu_to_le16(dma_len - off);
1288 dcmds->command = cpu_to_le16(dma_cmd);
1289 dcmds->phy_addr = cpu_to_le32(dma_addr + off);
1290 dcmds->xfer_status = 0;
1291 ++dcmds;
1292 dtot += dma_len - off;
1293 off = 0;
1294 }
1295 }
1296 }
1297 if (dtot == 0) {
1298 /* Either the target has overrun our buffer,
1299 or the caller didn't provide a buffer. */
1300 static char mesh_extra_buf[64];
1301
1302 dtot = sizeof(mesh_extra_buf);
1303 dcmds->req_count = cpu_to_le16(dtot);
1304 dcmds->phy_addr = cpu_to_le32(virt_to_phys(mesh_extra_buf));
1305 dcmds->xfer_status = 0;
1306 ++dcmds;
1307 }
1308 dma_cmd += OUTPUT_LAST - OUTPUT_MORE;
1309 dcmds[-1].command = cpu_to_le16(dma_cmd);
1310 memset(dcmds, 0, sizeof(*dcmds));
1311 dcmds->command = cpu_to_le16(DBDMA_STOP);
1312 ms->dma_count = dtot;
1313 }
1314
halt_dma(struct mesh_state * ms)1315 static void halt_dma(struct mesh_state *ms)
1316 {
1317 volatile struct dbdma_regs __iomem *md = ms->dma;
1318 volatile struct mesh_regs __iomem *mr = ms->mesh;
1319 struct scsi_cmnd *cmd = ms->current_req;
1320 int t, nb;
1321
1322 if (!ms->tgts[ms->conn_tgt].data_goes_out) {
1323 /* wait a little while until the fifo drains */
1324 t = 50;
1325 while (t > 0 && in_8(&mr->fifo_count) != 0
1326 && (in_le32(&md->status) & ACTIVE) != 0) {
1327 --t;
1328 udelay(1);
1329 }
1330 }
1331 out_le32(&md->control, RUN << 16); /* turn off RUN bit */
1332 nb = (mr->count_hi << 8) + mr->count_lo;
1333 dlog(ms, "halt_dma fc/count=%.6x",
1334 MKWORD(0, mr->fifo_count, 0, nb));
1335 if (ms->tgts[ms->conn_tgt].data_goes_out)
1336 nb += mr->fifo_count;
1337 /* nb is the number of bytes not yet transferred
1338 to/from the target. */
1339 ms->data_ptr -= nb;
1340 dlog(ms, "data_ptr %x", ms->data_ptr);
1341 if (ms->data_ptr < 0) {
1342 printk(KERN_ERR "mesh: halt_dma: data_ptr=%d (nb=%d, ms=%p)\n",
1343 ms->data_ptr, nb, ms);
1344 ms->data_ptr = 0;
1345 #ifdef MESH_DBG
1346 dumplog(ms, ms->conn_tgt);
1347 dumpslog(ms);
1348 #endif /* MESH_DBG */
1349 } else if (cmd && scsi_bufflen(cmd) &&
1350 ms->data_ptr > scsi_bufflen(cmd)) {
1351 printk(KERN_DEBUG "mesh: target %d overrun, "
1352 "data_ptr=%x total=%x goes_out=%d\n",
1353 ms->conn_tgt, ms->data_ptr, scsi_bufflen(cmd),
1354 ms->tgts[ms->conn_tgt].data_goes_out);
1355 }
1356 if (cmd)
1357 scsi_dma_unmap(cmd);
1358 ms->dma_started = 0;
1359 }
1360
phase_mismatch(struct mesh_state * ms)1361 static void phase_mismatch(struct mesh_state *ms)
1362 {
1363 volatile struct mesh_regs __iomem *mr = ms->mesh;
1364 int phase;
1365
1366 dlog(ms, "phasemm ch/cl/seq/fc=%.8x",
1367 MKWORD(mr->count_hi, mr->count_lo, mr->sequence, mr->fifo_count));
1368 phase = in_8(&mr->bus_status0) & BS0_PHASE;
1369 if (ms->msgphase == msg_out_xxx && phase == BP_MSGOUT) {
1370 /* output the last byte of the message, without ATN */
1371 out_8(&mr->count_lo, 1);
1372 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1373 mesh_flush_io(mr);
1374 udelay(1);
1375 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1376 ms->msgphase = msg_out_last;
1377 return;
1378 }
1379
1380 if (ms->msgphase == msg_in) {
1381 get_msgin(ms);
1382 if (ms->n_msgin)
1383 handle_msgin(ms);
1384 }
1385
1386 if (ms->dma_started)
1387 halt_dma(ms);
1388 if (mr->fifo_count) {
1389 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1390 mesh_flush_io(mr);
1391 udelay(1);
1392 }
1393
1394 ms->msgphase = msg_none;
1395 switch (phase) {
1396 case BP_DATAIN:
1397 ms->tgts[ms->conn_tgt].data_goes_out = 0;
1398 ms->phase = dataing;
1399 break;
1400 case BP_DATAOUT:
1401 ms->tgts[ms->conn_tgt].data_goes_out = 1;
1402 ms->phase = dataing;
1403 break;
1404 case BP_COMMAND:
1405 ms->phase = commanding;
1406 break;
1407 case BP_STATUS:
1408 ms->phase = statusing;
1409 break;
1410 case BP_MSGIN:
1411 ms->msgphase = msg_in;
1412 ms->n_msgin = 0;
1413 break;
1414 case BP_MSGOUT:
1415 ms->msgphase = msg_out;
1416 if (ms->n_msgout == 0) {
1417 if (ms->aborting) {
1418 do_abort(ms);
1419 } else {
1420 if (ms->last_n_msgout == 0) {
1421 printk(KERN_DEBUG
1422 "mesh: no msg to repeat\n");
1423 ms->msgout[0] = NOP;
1424 ms->last_n_msgout = 1;
1425 }
1426 ms->n_msgout = ms->last_n_msgout;
1427 }
1428 }
1429 break;
1430 default:
1431 printk(KERN_DEBUG "mesh: unknown scsi phase %x\n", phase);
1432 ms->stat = DID_ERROR;
1433 mesh_done(ms, 1);
1434 return;
1435 }
1436
1437 start_phase(ms);
1438 }
1439
cmd_complete(struct mesh_state * ms)1440 static void cmd_complete(struct mesh_state *ms)
1441 {
1442 volatile struct mesh_regs __iomem *mr = ms->mesh;
1443 struct scsi_cmnd *cmd = ms->current_req;
1444 struct mesh_target *tp = &ms->tgts[ms->conn_tgt];
1445 int seq, n, t;
1446
1447 dlog(ms, "cmd_complete fc=%x", mr->fifo_count);
1448 seq = use_active_neg + (ms->n_msgout? SEQ_ATN: 0);
1449 switch (ms->msgphase) {
1450 case msg_out_xxx:
1451 /* huh? we expected a phase mismatch */
1452 ms->n_msgin = 0;
1453 ms->msgphase = msg_in;
1454 fallthrough;
1455
1456 case msg_in:
1457 /* should have some message bytes in fifo */
1458 get_msgin(ms);
1459 n = msgin_length(ms);
1460 if (ms->n_msgin < n) {
1461 out_8(&mr->count_lo, n - ms->n_msgin);
1462 out_8(&mr->sequence, SEQ_MSGIN + seq);
1463 } else {
1464 ms->msgphase = msg_none;
1465 handle_msgin(ms);
1466 start_phase(ms);
1467 }
1468 break;
1469
1470 case msg_in_bad:
1471 out_8(&mr->sequence, SEQ_FLUSHFIFO);
1472 mesh_flush_io(mr);
1473 udelay(1);
1474 out_8(&mr->count_lo, 1);
1475 out_8(&mr->sequence, SEQ_MSGIN + SEQ_ATN + use_active_neg);
1476 break;
1477
1478 case msg_out:
1479 /*
1480 * To get the right timing on ATN wrt ACK, we have
1481 * to get the MESH to drop ACK, wait until REQ gets
1482 * asserted, then drop ATN. To do this we first
1483 * issue a SEQ_MSGOUT with ATN and wait for REQ,
1484 * then change the command to a SEQ_MSGOUT w/o ATN.
1485 * If we don't see REQ in a reasonable time, we
1486 * change the command to SEQ_MSGIN with ATN,
1487 * wait for the phase mismatch interrupt, then
1488 * issue the SEQ_MSGOUT without ATN.
1489 */
1490 out_8(&mr->count_lo, 1);
1491 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg + SEQ_ATN);
1492 t = 30; /* wait up to 30us */
1493 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0 && --t >= 0)
1494 udelay(1);
1495 dlog(ms, "last_mbyte err/exc/fc/cl=%.8x",
1496 MKWORD(mr->error, mr->exception,
1497 mr->fifo_count, mr->count_lo));
1498 if (in_8(&mr->interrupt) & (INT_ERROR | INT_EXCEPTION)) {
1499 /* whoops, target didn't do what we expected */
1500 ms->last_n_msgout = ms->n_msgout;
1501 ms->n_msgout = 0;
1502 if (in_8(&mr->interrupt) & INT_ERROR) {
1503 printk(KERN_ERR "mesh: error %x in msg_out\n",
1504 in_8(&mr->error));
1505 handle_error(ms);
1506 return;
1507 }
1508 if (in_8(&mr->exception) != EXC_PHASEMM)
1509 printk(KERN_ERR "mesh: exc %x in msg_out\n",
1510 in_8(&mr->exception));
1511 else
1512 printk(KERN_DEBUG "mesh: bs0=%x in msg_out\n",
1513 in_8(&mr->bus_status0));
1514 handle_exception(ms);
1515 return;
1516 }
1517 if (in_8(&mr->bus_status0) & BS0_REQ) {
1518 out_8(&mr->sequence, SEQ_MSGOUT + use_active_neg);
1519 mesh_flush_io(mr);
1520 udelay(1);
1521 out_8(&mr->fifo, ms->msgout[ms->n_msgout-1]);
1522 ms->msgphase = msg_out_last;
1523 } else {
1524 out_8(&mr->sequence, SEQ_MSGIN + use_active_neg + SEQ_ATN);
1525 ms->msgphase = msg_out_xxx;
1526 }
1527 break;
1528
1529 case msg_out_last:
1530 ms->last_n_msgout = ms->n_msgout;
1531 ms->n_msgout = 0;
1532 ms->msgphase = ms->expect_reply? msg_in: msg_none;
1533 start_phase(ms);
1534 break;
1535
1536 case msg_none:
1537 switch (ms->phase) {
1538 case idle:
1539 printk(KERN_ERR "mesh: interrupt in idle phase?\n");
1540 dumpslog(ms);
1541 return;
1542 case selecting:
1543 dlog(ms, "Selecting phase at command completion",0);
1544 ms->msgout[0] = IDENTIFY(ALLOW_RESEL(ms->conn_tgt),
1545 (cmd? cmd->device->lun: 0));
1546 ms->n_msgout = 1;
1547 ms->expect_reply = 0;
1548 if (ms->aborting) {
1549 ms->msgout[0] = ABORT;
1550 ms->n_msgout++;
1551 } else if (tp->sdtr_state == do_sdtr) {
1552 /* add SDTR message */
1553 add_sdtr_msg(ms);
1554 ms->expect_reply = 1;
1555 tp->sdtr_state = sdtr_sent;
1556 }
1557 ms->msgphase = msg_out;
1558 /*
1559 * We need to wait for REQ before dropping ATN.
1560 * We wait for at most 30us, then fall back to
1561 * a scheme where we issue a SEQ_COMMAND with ATN,
1562 * which will give us a phase mismatch interrupt
1563 * when REQ does come, and then we send the message.
1564 */
1565 t = 230; /* wait up to 230us */
1566 while ((in_8(&mr->bus_status0) & BS0_REQ) == 0) {
1567 if (--t < 0) {
1568 dlog(ms, "impatient for req", ms->n_msgout);
1569 ms->msgphase = msg_none;
1570 break;
1571 }
1572 udelay(1);
1573 }
1574 break;
1575 case dataing:
1576 if (ms->dma_count != 0) {
1577 start_phase(ms);
1578 return;
1579 }
1580 /*
1581 * We can get a phase mismatch here if the target
1582 * changes to the status phase, even though we have
1583 * had a command complete interrupt. Then, if we
1584 * issue the SEQ_STATUS command, we'll get a sequence
1585 * error interrupt. Which isn't so bad except that
1586 * occasionally the mesh actually executes the
1587 * SEQ_STATUS *as well as* giving us the sequence
1588 * error and phase mismatch exception.
1589 */
1590 out_8(&mr->sequence, 0);
1591 out_8(&mr->interrupt,
1592 INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1593 halt_dma(ms);
1594 break;
1595 case statusing:
1596 if (cmd) {
1597 struct mesh_cmd_priv *mcmd = mesh_priv(cmd);
1598
1599 mcmd->status = mr->fifo;
1600 if (DEBUG_TARGET(cmd))
1601 printk(KERN_DEBUG "mesh: status is %x\n",
1602 mcmd->status);
1603 }
1604 ms->msgphase = msg_in;
1605 break;
1606 case busfreeing:
1607 mesh_done(ms, 1);
1608 return;
1609 case disconnecting:
1610 ms->current_req = NULL;
1611 ms->phase = idle;
1612 mesh_start(ms);
1613 return;
1614 default:
1615 break;
1616 }
1617 ++ms->phase;
1618 start_phase(ms);
1619 break;
1620 }
1621 }
1622
1623
1624 /*
1625 * Called by midlayer with host locked to queue a new
1626 * request
1627 */
mesh_queue_lck(struct scsi_cmnd * cmd)1628 static int mesh_queue_lck(struct scsi_cmnd *cmd)
1629 {
1630 struct mesh_state *ms;
1631
1632 cmd->host_scribble = NULL;
1633
1634 ms = (struct mesh_state *) cmd->device->host->hostdata;
1635
1636 if (ms->request_q == NULL)
1637 ms->request_q = cmd;
1638 else
1639 ms->request_qtail->host_scribble = (void *) cmd;
1640 ms->request_qtail = cmd;
1641
1642 if (ms->phase == idle)
1643 mesh_start(ms);
1644
1645 return 0;
1646 }
1647
DEF_SCSI_QCMD(mesh_queue)1648 static DEF_SCSI_QCMD(mesh_queue)
1649
1650 /*
1651 * Called to handle interrupts, either call by the interrupt
1652 * handler (do_mesh_interrupt) or by other functions in
1653 * exceptional circumstances
1654 */
1655 static void mesh_interrupt(struct mesh_state *ms)
1656 {
1657 volatile struct mesh_regs __iomem *mr = ms->mesh;
1658 int intr;
1659
1660 #if 0
1661 if (ALLOW_DEBUG(ms->conn_tgt))
1662 printk(KERN_DEBUG "mesh_intr, bs0=%x int=%x exc=%x err=%x "
1663 "phase=%d msgphase=%d\n", mr->bus_status0,
1664 mr->interrupt, mr->exception, mr->error,
1665 ms->phase, ms->msgphase);
1666 #endif
1667 while ((intr = in_8(&mr->interrupt)) != 0) {
1668 dlog(ms, "interrupt intr/err/exc/seq=%.8x",
1669 MKWORD(intr, mr->error, mr->exception, mr->sequence));
1670 if (intr & INT_ERROR) {
1671 handle_error(ms);
1672 } else if (intr & INT_EXCEPTION) {
1673 handle_exception(ms);
1674 } else if (intr & INT_CMDDONE) {
1675 out_8(&mr->interrupt, INT_CMDDONE);
1676 cmd_complete(ms);
1677 }
1678 }
1679 }
1680
1681 /* Todo: here we can at least try to remove the command from the
1682 * queue if it isn't connected yet, and for pending command, assert
1683 * ATN until the bus gets freed.
1684 */
mesh_abort(struct scsi_cmnd * cmd)1685 static int mesh_abort(struct scsi_cmnd *cmd)
1686 {
1687 struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1688
1689 printk(KERN_DEBUG "mesh_abort(%p)\n", cmd);
1690 mesh_dump_regs(ms);
1691 dumplog(ms, cmd->device->id);
1692 dumpslog(ms);
1693 return FAILED;
1694 }
1695
1696 /*
1697 * Called by the midlayer with the lock held to reset the
1698 * SCSI host and bus.
1699 * The midlayer will wait for devices to come back, we don't need
1700 * to do that ourselves
1701 */
mesh_host_reset(struct scsi_cmnd * cmd)1702 static int mesh_host_reset(struct scsi_cmnd *cmd)
1703 {
1704 struct mesh_state *ms = (struct mesh_state *) cmd->device->host->hostdata;
1705 volatile struct mesh_regs __iomem *mr = ms->mesh;
1706 volatile struct dbdma_regs __iomem *md = ms->dma;
1707 unsigned long flags;
1708
1709 printk(KERN_DEBUG "mesh_host_reset\n");
1710
1711 spin_lock_irqsave(ms->host->host_lock, flags);
1712
1713 if (ms->dma_started)
1714 halt_dma(ms);
1715
1716 /* Reset the controller & dbdma channel */
1717 out_le32(&md->control, (RUN|PAUSE|FLUSH|WAKE) << 16); /* stop dma */
1718 out_8(&mr->exception, 0xff); /* clear all exception bits */
1719 out_8(&mr->error, 0xff); /* clear all error bits */
1720 out_8(&mr->sequence, SEQ_RESETMESH);
1721 mesh_flush_io(mr);
1722 udelay(1);
1723 out_8(&mr->intr_mask, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1724 out_8(&mr->source_id, ms->host->this_id);
1725 out_8(&mr->sel_timeout, 25); /* 250ms */
1726 out_8(&mr->sync_params, ASYNC_PARAMS);
1727
1728 /* Reset the bus */
1729 out_8(&mr->bus_status1, BS1_RST); /* assert RST */
1730 mesh_flush_io(mr);
1731 udelay(30); /* leave it on for >= 25us */
1732 out_8(&mr->bus_status1, 0); /* negate RST */
1733
1734 /* Complete pending commands */
1735 handle_reset(ms);
1736
1737 spin_unlock_irqrestore(ms->host->host_lock, flags);
1738 return SUCCESS;
1739 }
1740
set_mesh_power(struct mesh_state * ms,int state)1741 static void set_mesh_power(struct mesh_state *ms, int state)
1742 {
1743 if (!machine_is(powermac))
1744 return;
1745 if (state) {
1746 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 1);
1747 msleep(200);
1748 } else {
1749 pmac_call_feature(PMAC_FTR_MESH_ENABLE, macio_get_of_node(ms->mdev), 0, 0);
1750 msleep(10);
1751 }
1752 }
1753
1754
1755 #ifdef CONFIG_PM
mesh_suspend(struct macio_dev * mdev,pm_message_t mesg)1756 static int mesh_suspend(struct macio_dev *mdev, pm_message_t mesg)
1757 {
1758 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1759 unsigned long flags;
1760
1761 switch (mesg.event) {
1762 case PM_EVENT_SUSPEND:
1763 case PM_EVENT_HIBERNATE:
1764 case PM_EVENT_FREEZE:
1765 break;
1766 default:
1767 return 0;
1768 }
1769 if (ms->phase == sleeping)
1770 return 0;
1771
1772 scsi_block_requests(ms->host);
1773 spin_lock_irqsave(ms->host->host_lock, flags);
1774 while(ms->phase != idle) {
1775 spin_unlock_irqrestore(ms->host->host_lock, flags);
1776 msleep(10);
1777 spin_lock_irqsave(ms->host->host_lock, flags);
1778 }
1779 ms->phase = sleeping;
1780 spin_unlock_irqrestore(ms->host->host_lock, flags);
1781 disable_irq(ms->meshintr);
1782 set_mesh_power(ms, 0);
1783
1784 return 0;
1785 }
1786
mesh_resume(struct macio_dev * mdev)1787 static int mesh_resume(struct macio_dev *mdev)
1788 {
1789 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1790 unsigned long flags;
1791
1792 if (ms->phase != sleeping)
1793 return 0;
1794
1795 set_mesh_power(ms, 1);
1796 mesh_init(ms);
1797 spin_lock_irqsave(ms->host->host_lock, flags);
1798 mesh_start(ms);
1799 spin_unlock_irqrestore(ms->host->host_lock, flags);
1800 enable_irq(ms->meshintr);
1801 scsi_unblock_requests(ms->host);
1802
1803 return 0;
1804 }
1805
1806 #endif /* CONFIG_PM */
1807
1808 /*
1809 * If we leave drives set for synchronous transfers (especially
1810 * CDROMs), and reboot to MacOS, it gets confused, poor thing.
1811 * So, on reboot we reset the SCSI bus.
1812 */
mesh_shutdown(struct macio_dev * mdev)1813 static int mesh_shutdown(struct macio_dev *mdev)
1814 {
1815 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1816 volatile struct mesh_regs __iomem *mr;
1817 unsigned long flags;
1818
1819 printk(KERN_INFO "resetting MESH scsi bus(es)\n");
1820 spin_lock_irqsave(ms->host->host_lock, flags);
1821 mr = ms->mesh;
1822 out_8(&mr->intr_mask, 0);
1823 out_8(&mr->interrupt, INT_ERROR | INT_EXCEPTION | INT_CMDDONE);
1824 out_8(&mr->bus_status1, BS1_RST);
1825 mesh_flush_io(mr);
1826 udelay(30);
1827 out_8(&mr->bus_status1, 0);
1828 spin_unlock_irqrestore(ms->host->host_lock, flags);
1829
1830 return 0;
1831 }
1832
1833 static const struct scsi_host_template mesh_template = {
1834 .proc_name = "mesh",
1835 .name = "MESH",
1836 .queuecommand = mesh_queue,
1837 .eh_abort_handler = mesh_abort,
1838 .eh_host_reset_handler = mesh_host_reset,
1839 .can_queue = 20,
1840 .this_id = 7,
1841 .sg_tablesize = SG_ALL,
1842 .cmd_per_lun = 2,
1843 .max_segment_size = 65535,
1844 .cmd_size = sizeof(struct mesh_cmd_priv),
1845 };
1846
mesh_probe(struct macio_dev * mdev,const struct of_device_id * match)1847 static int mesh_probe(struct macio_dev *mdev, const struct of_device_id *match)
1848 {
1849 struct device_node *mesh = macio_get_of_node(mdev);
1850 struct pci_dev* pdev = macio_get_pci_dev(mdev);
1851 int tgt, minper;
1852 const int *cfp;
1853 struct mesh_state *ms;
1854 struct Scsi_Host *mesh_host;
1855 void *dma_cmd_space;
1856 dma_addr_t dma_cmd_bus;
1857
1858 switch (mdev->bus->chip->type) {
1859 case macio_heathrow:
1860 case macio_gatwick:
1861 case macio_paddington:
1862 use_active_neg = 0;
1863 break;
1864 default:
1865 use_active_neg = SEQ_ACTIVE_NEG;
1866 }
1867
1868 if (macio_resource_count(mdev) != 2 || macio_irq_count(mdev) != 2) {
1869 printk(KERN_ERR "mesh: expected 2 addrs and 2 intrs"
1870 " (got %d,%d)\n", macio_resource_count(mdev),
1871 macio_irq_count(mdev));
1872 return -ENODEV;
1873 }
1874
1875 if (macio_request_resources(mdev, "mesh") != 0) {
1876 printk(KERN_ERR "mesh: unable to request memory resources");
1877 return -EBUSY;
1878 }
1879 mesh_host = scsi_host_alloc(&mesh_template, sizeof(struct mesh_state));
1880 if (mesh_host == NULL) {
1881 printk(KERN_ERR "mesh: couldn't register host");
1882 goto out_release;
1883 }
1884
1885 mesh_host->base = macio_resource_start(mdev, 0);
1886 mesh_host->irq = macio_irq(mdev, 0);
1887 ms = (struct mesh_state *) mesh_host->hostdata;
1888 macio_set_drvdata(mdev, ms);
1889 ms->host = mesh_host;
1890 ms->mdev = mdev;
1891 ms->pdev = pdev;
1892
1893 ms->mesh = ioremap(macio_resource_start(mdev, 0), 0x1000);
1894 if (ms->mesh == NULL) {
1895 printk(KERN_ERR "mesh: can't map registers\n");
1896 goto out_free;
1897 }
1898 ms->dma = ioremap(macio_resource_start(mdev, 1), 0x1000);
1899 if (ms->dma == NULL) {
1900 printk(KERN_ERR "mesh: can't map registers\n");
1901 iounmap(ms->mesh);
1902 goto out_free;
1903 }
1904
1905 ms->meshintr = macio_irq(mdev, 0);
1906 ms->dmaintr = macio_irq(mdev, 1);
1907
1908 /* Space for dma command list: +1 for stop command,
1909 * +1 to allow for aligning.
1910 */
1911 ms->dma_cmd_size = (mesh_host->sg_tablesize + 2) * sizeof(struct dbdma_cmd);
1912
1913 /* We use the PCI APIs for now until the generic one gets fixed
1914 * enough or until we get some macio-specific versions
1915 */
1916 dma_cmd_space = dma_alloc_coherent(&macio_get_pci_dev(mdev)->dev,
1917 ms->dma_cmd_size, &dma_cmd_bus,
1918 GFP_KERNEL);
1919 if (dma_cmd_space == NULL) {
1920 printk(KERN_ERR "mesh: can't allocate DMA table\n");
1921 goto out_unmap;
1922 }
1923
1924 ms->dma_cmds = (struct dbdma_cmd *) DBDMA_ALIGN(dma_cmd_space);
1925 ms->dma_cmd_space = dma_cmd_space;
1926 ms->dma_cmd_bus = dma_cmd_bus + ((unsigned long)ms->dma_cmds)
1927 - (unsigned long)dma_cmd_space;
1928 ms->current_req = NULL;
1929 for (tgt = 0; tgt < 8; ++tgt) {
1930 ms->tgts[tgt].sdtr_state = do_sdtr;
1931 ms->tgts[tgt].sync_params = ASYNC_PARAMS;
1932 ms->tgts[tgt].current_req = NULL;
1933 }
1934
1935 if ((cfp = of_get_property(mesh, "clock-frequency", NULL)))
1936 ms->clk_freq = *cfp;
1937 else {
1938 printk(KERN_INFO "mesh: assuming 50MHz clock frequency\n");
1939 ms->clk_freq = 50000000;
1940 }
1941
1942 /* The maximum sync rate is clock / 5; increase
1943 * mesh_sync_period if necessary.
1944 */
1945 minper = 1000000000 / (ms->clk_freq / 5); /* ns */
1946 if (mesh_sync_period < minper)
1947 mesh_sync_period = minper;
1948
1949 /* Power up the chip */
1950 set_mesh_power(ms, 1);
1951
1952 /* Set it up */
1953 mesh_init(ms);
1954
1955 /* Request interrupt */
1956 if (request_irq(ms->meshintr, do_mesh_interrupt, 0, "MESH", ms)) {
1957 printk(KERN_ERR "MESH: can't get irq %d\n", ms->meshintr);
1958 goto out_shutdown;
1959 }
1960
1961 /* Add scsi host & scan */
1962 if (scsi_add_host(mesh_host, &mdev->ofdev.dev))
1963 goto out_release_irq;
1964 scsi_scan_host(mesh_host);
1965
1966 return 0;
1967
1968 out_release_irq:
1969 free_irq(ms->meshintr, ms);
1970 out_shutdown:
1971 /* shutdown & reset bus in case of error or macos can be confused
1972 * at reboot if the bus was set to synchronous mode already
1973 */
1974 mesh_shutdown(mdev);
1975 set_mesh_power(ms, 0);
1976 dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size,
1977 ms->dma_cmd_space, ms->dma_cmd_bus);
1978 out_unmap:
1979 iounmap(ms->dma);
1980 iounmap(ms->mesh);
1981 out_free:
1982 scsi_host_put(mesh_host);
1983 out_release:
1984 macio_release_resources(mdev);
1985
1986 return -ENODEV;
1987 }
1988
mesh_remove(struct macio_dev * mdev)1989 static int mesh_remove(struct macio_dev *mdev)
1990 {
1991 struct mesh_state *ms = (struct mesh_state *)macio_get_drvdata(mdev);
1992 struct Scsi_Host *mesh_host = ms->host;
1993
1994 scsi_remove_host(mesh_host);
1995
1996 free_irq(ms->meshintr, ms);
1997
1998 /* Reset scsi bus */
1999 mesh_shutdown(mdev);
2000
2001 /* Shut down chip & termination */
2002 set_mesh_power(ms, 0);
2003
2004 /* Unmap registers & dma controller */
2005 iounmap(ms->mesh);
2006 iounmap(ms->dma);
2007
2008 /* Free DMA commands memory */
2009 dma_free_coherent(&macio_get_pci_dev(mdev)->dev, ms->dma_cmd_size,
2010 ms->dma_cmd_space, ms->dma_cmd_bus);
2011
2012 /* Release memory resources */
2013 macio_release_resources(mdev);
2014
2015 scsi_host_put(mesh_host);
2016
2017 return 0;
2018 }
2019
2020
2021 static struct of_device_id mesh_match[] =
2022 {
2023 {
2024 .name = "mesh",
2025 },
2026 {
2027 .type = "scsi",
2028 .compatible = "chrp,mesh0"
2029 },
2030 {},
2031 };
2032 MODULE_DEVICE_TABLE (of, mesh_match);
2033
2034 static struct macio_driver mesh_driver =
2035 {
2036 .driver = {
2037 .name = "mesh",
2038 .owner = THIS_MODULE,
2039 .of_match_table = mesh_match,
2040 },
2041 .probe = mesh_probe,
2042 .remove = mesh_remove,
2043 .shutdown = mesh_shutdown,
2044 #ifdef CONFIG_PM
2045 .suspend = mesh_suspend,
2046 .resume = mesh_resume,
2047 #endif
2048 };
2049
2050
init_mesh(void)2051 static int __init init_mesh(void)
2052 {
2053
2054 /* Calculate sync rate from module parameters */
2055 if (sync_rate > 10)
2056 sync_rate = 10;
2057 if (sync_rate > 0) {
2058 printk(KERN_INFO "mesh: configured for synchronous %d MB/s\n", sync_rate);
2059 mesh_sync_period = 1000 / sync_rate; /* ns */
2060 mesh_sync_offset = 15;
2061 } else
2062 printk(KERN_INFO "mesh: configured for asynchronous\n");
2063
2064 return macio_register_driver(&mesh_driver);
2065 }
2066
exit_mesh(void)2067 static void __exit exit_mesh(void)
2068 {
2069 return macio_unregister_driver(&mesh_driver);
2070 }
2071
2072 module_init(init_mesh);
2073 module_exit(exit_mesh);
2074