xref: /openbmc/linux/sound/mips/hal2.h (revision 75bf465f0bc33e9b776a46d6a1b9b990f5fb7c37)
1  /* SPDX-License-Identifier: GPL-2.0-only */
2  #ifndef __HAL2_H
3  #define __HAL2_H
4  
5  /*
6   *  Driver for HAL2 sound processors
7   *  Copyright (c) 1999 Ulf Carlsson <ulfc@bun.falkenberg.se>
8   *  Copyright (c) 2001, 2002, 2003 Ladislav Michl <ladis@linux-mips.org>
9   */
10  
11  #include <linux/types.h>
12  
13  /* Indirect status register */
14  
15  #define H2_ISR_TSTATUS		0x01	/* RO: transaction status 1=busy */
16  #define H2_ISR_USTATUS		0x02	/* RO: utime status bit 1=armed */
17  #define H2_ISR_QUAD_MODE	0x04	/* codec mode 0=indigo 1=quad */
18  #define H2_ISR_GLOBAL_RESET_N	0x08	/* chip global reset 0=reset */
19  #define H2_ISR_CODEC_RESET_N	0x10	/* codec/synth reset 0=reset  */
20  
21  /* Revision register */
22  
23  #define H2_REV_AUDIO_PRESENT	0x8000	/* RO: audio present 0=present */
24  #define H2_REV_BOARD_M		0x7000	/* RO: bits 14:12, board revision */
25  #define H2_REV_MAJOR_CHIP_M	0x00F0	/* RO: bits 7:4, major chip revision */
26  #define H2_REV_MINOR_CHIP_M	0x000F	/* RO: bits 3:0, minor chip revision */
27  
28  /* Indirect address register */
29  
30  /*
31   * Address of indirect internal register to be accessed. A write to this
32   * register initiates read or write access to the indirect registers in the
33   * HAL2. Note that there af four indirect data registers for write access to
34   * registers larger than 16 byte.
35   */
36  
37  #define H2_IAR_TYPE_M		0xF000	/* bits 15:12, type of functional */
38  					/* block the register resides in */
39  					/* 1=DMA Port */
40  					/* 9=Global DMA Control */
41  					/* 2=Bresenham */
42  					/* 3=Unix Timer */
43  #define H2_IAR_NUM_M		0x0F00	/* bits 11:8 instance of the */
44  					/* blockin which the indirect */
45  					/* register resides */
46  					/* If IAR_TYPE_M=DMA Port: */
47  					/* 1=Synth In */
48  					/* 2=AES In */
49  					/* 3=AES Out */
50  					/* 4=DAC Out */
51  					/* 5=ADC Out */
52  					/* 6=Synth Control */
53  					/* If IAR_TYPE_M=Global DMA Control: */
54  					/* 1=Control */
55  					/* If IAR_TYPE_M=Bresenham: */
56  					/* 1=Bresenham Clock Gen 1 */
57  					/* 2=Bresenham Clock Gen 2 */
58  					/* 3=Bresenham Clock Gen 3 */
59  					/* If IAR_TYPE_M=Unix Timer: */
60  					/* 1=Unix Timer */
61  #define H2_IAR_ACCESS_SELECT	0x0080	/* 1=read 0=write */
62  #define H2_IAR_PARAM		0x000C	/* Parameter Select */
63  #define H2_IAR_RB_INDEX_M	0x0003	/* Read Back Index */
64  					/* 00:word0 */
65  					/* 01:word1 */
66  					/* 10:word2 */
67  					/* 11:word3 */
68  /*
69   * HAL2 internal addressing
70   *
71   * The HAL2 has "indirect registers" (idr) which are accessed by writing to the
72   * Indirect Data registers. Write the address to the Indirect Address register
73   * to transfer the data.
74   *
75   * We define the H2IR_* to the read address and H2IW_* to the write address and
76   * H2I_* to be fields in whatever register is referred to.
77   *
78   * When we write to indirect registers which are larger than one word (16 bit)
79   * we have to fill more than one indirect register before writing. When we read
80   * back however we have to read several times, each time with different Read
81   * Back Indexes (there are defs for doing this easily).
82   */
83  
84  /*
85   * Relay Control
86   */
87  #define H2I_RELAY_C		0x9100
88  #define H2I_RELAY_C_STATE	0x01		/* state of RELAY pin signal */
89  
90  /* DMA port enable */
91  
92  #define H2I_DMA_PORT_EN		0x9104
93  #define H2I_DMA_PORT_EN_SY_IN	0x01		/* Synth_in DMA port */
94  #define H2I_DMA_PORT_EN_AESRX	0x02		/* AES receiver DMA port */
95  #define H2I_DMA_PORT_EN_AESTX	0x04		/* AES transmitter DMA port */
96  #define H2I_DMA_PORT_EN_CODECTX	0x08		/* CODEC transmit DMA port */
97  #define H2I_DMA_PORT_EN_CODECR	0x10		/* CODEC receive DMA port */
98  
99  #define H2I_DMA_END		0x9108 		/* global dma endian select */
100  #define H2I_DMA_END_SY_IN	0x01		/* Synth_in DMA port */
101  #define H2I_DMA_END_AESRX	0x02		/* AES receiver DMA port */
102  #define H2I_DMA_END_AESTX	0x04		/* AES transmitter DMA port */
103  #define H2I_DMA_END_CODECTX	0x08		/* CODEC transmit DMA port */
104  #define H2I_DMA_END_CODECR	0x10		/* CODEC receive DMA port */
105  						/* 0=b_end 1=l_end */
106  
107  #define H2I_DMA_DRV		0x910C  	/* global PBUS DMA enable */
108  
109  #define H2I_SYNTH_C		0x1104		/* Synth DMA control */
110  
111  #define H2I_AESRX_C		0x1204	 	/* AES RX dma control */
112  
113  #define H2I_C_TS_EN		0x20		/* Timestamp enable */
114  #define H2I_C_TS_FRMT		0x40		/* Timestamp format */
115  #define H2I_C_NAUDIO		0x80		/* Sign extend */
116  
117  /* AESRX CTL, 16 bit */
118  
119  #define H2I_AESTX_C		0x1304		/* AES TX DMA control */
120  #define H2I_AESTX_C_CLKID_SHIFT	3		/* Bresenham Clock Gen 1-3 */
121  #define H2I_AESTX_C_CLKID_M	0x18
122  #define H2I_AESTX_C_DATAT_SHIFT	8		/* 1=mono 2=stereo (3=quad) */
123  #define H2I_AESTX_C_DATAT_M	0x300
124  
125  /* CODEC registers */
126  
127  #define H2I_DAC_C1		0x1404 		/* DAC DMA control, 16 bit */
128  #define H2I_DAC_C2		0x1408		/* DAC DMA control, 32 bit */
129  #define H2I_ADC_C1		0x1504 		/* ADC DMA control, 16 bit */
130  #define H2I_ADC_C2		0x1508		/* ADC DMA control, 32 bit */
131  
132  /* Bits in CTL1 register */
133  
134  #define H2I_C1_DMA_SHIFT	0		/* DMA channel */
135  #define H2I_C1_DMA_M		0x7
136  #define H2I_C1_CLKID_SHIFT	3		/* Bresenham Clock Gen 1-3 */
137  #define H2I_C1_CLKID_M		0x18
138  #define H2I_C1_DATAT_SHIFT	8		/* 1=mono 2=stereo (3=quad) */
139  #define H2I_C1_DATAT_M		0x300
140  
141  /* Bits in CTL2 register */
142  
143  #define H2I_C2_R_GAIN_SHIFT	0		/* right a/d input gain */
144  #define H2I_C2_R_GAIN_M		0xf
145  #define H2I_C2_L_GAIN_SHIFT	4		/* left a/d input gain */
146  #define H2I_C2_L_GAIN_M		0xf0
147  #define H2I_C2_R_SEL		0x100		/* right input select */
148  #define H2I_C2_L_SEL		0x200		/* left input select */
149  #define H2I_C2_MUTE		0x400		/* mute */
150  #define H2I_C2_DO1		0x00010000	/* digital output port bit 0 */
151  #define H2I_C2_DO2		0x00020000	/* digital output port bit 1 */
152  #define H2I_C2_R_ATT_SHIFT	18		/* right d/a output - */
153  #define H2I_C2_R_ATT_M		0x007c0000	/* attenuation */
154  #define H2I_C2_L_ATT_SHIFT	23		/* left d/a output - */
155  #define H2I_C2_L_ATT_M		0x0f800000	/* attenuation */
156  
157  #define H2I_SYNTH_MAP_C		0x1104		/* synth dma handshake ctrl */
158  
159  /* Clock generator CTL 1, 16 bit */
160  
161  #define H2I_BRES1_C1		0x2104
162  #define H2I_BRES2_C1		0x2204
163  #define H2I_BRES3_C1		0x2304
164  
165  #define H2I_BRES_C1_SHIFT	0		/* 0=48.0 1=44.1 2=aes_rx */
166  #define H2I_BRES_C1_M		0x03
167  
168  /* Clock generator CTL 2, 32 bit */
169  
170  #define H2I_BRES1_C2		0x2108
171  #define H2I_BRES2_C2		0x2208
172  #define H2I_BRES3_C2		0x2308
173  
174  #define H2I_BRES_C2_INC_SHIFT	0		/* increment value */
175  #define H2I_BRES_C2_INC_M	0xffff
176  #define H2I_BRES_C2_MOD_SHIFT	16		/* modcontrol value */
177  #define H2I_BRES_C2_MOD_M	0xffff0000	/* modctrl=0xffff&(modinc-1) */
178  
179  /* Unix timer, 64 bit */
180  
181  #define H2I_UTIME		0x3104
182  #define H2I_UTIME_0_LD		0xffff		/* microseconds, LSB's */
183  #define H2I_UTIME_1_LD0		0x0f		/* microseconds, MSB's */
184  #define H2I_UTIME_1_LD1		0xf0		/* tenths of microseconds */
185  #define H2I_UTIME_2_LD		0xffff		/* seconds, LSB's */
186  #define H2I_UTIME_3_LD		0xffff		/* seconds, MSB's */
187  
188  struct hal2_ctl_regs {
189  	u32 _unused0[4];
190  	u32 isr;		/* 0x10 Status Register */
191  	u32 _unused1[3];
192  	u32 rev;		/* 0x20 Revision Register */
193  	u32 _unused2[3];
194  	u32 iar;		/* 0x30 Indirect Address Register */
195  	u32 _unused3[3];
196  	u32 idr0;		/* 0x40 Indirect Data Register 0 */
197  	u32 _unused4[3];
198  	u32 idr1;		/* 0x50 Indirect Data Register 1 */
199  	u32 _unused5[3];
200  	u32 idr2;		/* 0x60 Indirect Data Register 2 */
201  	u32 _unused6[3];
202  	u32 idr3;		/* 0x70 Indirect Data Register 3 */
203  };
204  
205  struct hal2_aes_regs {
206  	u32 rx_stat[2];	/* Status registers */
207  	u32 rx_cr[2];		/* Control registers */
208  	u32 rx_ud[4];		/* User data window */
209  	u32 rx_st[24];		/* Channel status data */
210  
211  	u32 tx_stat[1];	/* Status register */
212  	u32 tx_cr[3];		/* Control registers */
213  	u32 tx_ud[4];		/* User data window */
214  	u32 tx_st[24];		/* Channel status data */
215  };
216  
217  struct hal2_vol_regs {
218  	u32 right;		/* Right volume */
219  	u32 left;		/* Left volume */
220  };
221  
222  struct hal2_syn_regs {
223  	u32 _unused0[2];
224  	u32 page;		/* DOC Page register */
225  	u32 regsel;		/* DOC Register selection */
226  	u32 dlow;		/* DOC Data low */
227  	u32 dhigh;		/* DOC Data high */
228  	u32 irq;		/* IRQ Status */
229  	u32 dram;		/* DRAM Access */
230  };
231  
232  #endif	/* __HAL2_H */
233