xref: /openbmc/u-boot/drivers/net/zynq_gem.c (revision d01806a8)
1 // SPDX-License-Identifier: GPL-2.0+
2 /*
3  * (C) Copyright 2011 Michal Simek
4  *
5  * Michal SIMEK <monstr@monstr.eu>
6  *
7  * Based on Xilinx gmac driver:
8  * (C) Copyright 2011 Xilinx
9  */
10 
11 #include <clk.h>
12 #include <common.h>
13 #include <dm.h>
14 #include <net.h>
15 #include <netdev.h>
16 #include <config.h>
17 #include <console.h>
18 #include <malloc.h>
19 #include <asm/io.h>
20 #include <phy.h>
21 #include <miiphy.h>
22 #include <wait_bit.h>
23 #include <watchdog.h>
24 #include <asm/system.h>
25 #include <asm/arch/hardware.h>
26 #include <asm/arch/sys_proto.h>
27 #include <linux/errno.h>
28 
29 DECLARE_GLOBAL_DATA_PTR;
30 
31 /* Bit/mask specification */
32 #define ZYNQ_GEM_PHYMNTNC_OP_MASK	0x40020000 /* operation mask bits */
33 #define ZYNQ_GEM_PHYMNTNC_OP_R_MASK	0x20000000 /* read operation */
34 #define ZYNQ_GEM_PHYMNTNC_OP_W_MASK	0x10000000 /* write operation */
35 #define ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK	23 /* Shift bits for PHYAD */
36 #define ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK	18 /* Shift bits for PHREG */
37 
38 #define ZYNQ_GEM_RXBUF_EOF_MASK		0x00008000 /* End of frame. */
39 #define ZYNQ_GEM_RXBUF_SOF_MASK		0x00004000 /* Start of frame. */
40 #define ZYNQ_GEM_RXBUF_LEN_MASK		0x00003FFF /* Mask for length field */
41 
42 #define ZYNQ_GEM_RXBUF_WRAP_MASK	0x00000002 /* Wrap bit, last BD */
43 #define ZYNQ_GEM_RXBUF_NEW_MASK		0x00000001 /* Used bit.. */
44 #define ZYNQ_GEM_RXBUF_ADD_MASK		0xFFFFFFFC /* Mask for address */
45 
46 /* Wrap bit, last descriptor */
47 #define ZYNQ_GEM_TXBUF_WRAP_MASK	0x40000000
48 #define ZYNQ_GEM_TXBUF_LAST_MASK	0x00008000 /* Last buffer */
49 #define ZYNQ_GEM_TXBUF_USED_MASK	0x80000000 /* Used by Hw */
50 
51 #define ZYNQ_GEM_NWCTRL_TXEN_MASK	0x00000008 /* Enable transmit */
52 #define ZYNQ_GEM_NWCTRL_RXEN_MASK	0x00000004 /* Enable receive */
53 #define ZYNQ_GEM_NWCTRL_MDEN_MASK	0x00000010 /* Enable MDIO port */
54 #define ZYNQ_GEM_NWCTRL_STARTTX_MASK	0x00000200 /* Start tx (tx_go) */
55 
56 #define ZYNQ_GEM_NWCFG_SPEED100		0x00000001 /* 100 Mbps operation */
57 #define ZYNQ_GEM_NWCFG_SPEED1000	0x00000400 /* 1Gbps operation */
58 #define ZYNQ_GEM_NWCFG_FDEN		0x00000002 /* Full Duplex mode */
59 #define ZYNQ_GEM_NWCFG_FSREM		0x00020000 /* FCS removal */
60 #define ZYNQ_GEM_NWCFG_SGMII_ENBL	0x08000000 /* SGMII Enable */
61 #define ZYNQ_GEM_NWCFG_PCS_SEL		0x00000800 /* PCS select */
62 #ifdef CONFIG_ARM64
63 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x00100000 /* Div pclk by 64, max 160MHz */
64 #else
65 #define ZYNQ_GEM_NWCFG_MDCCLKDIV	0x000c0000 /* Div pclk by 48, max 120MHz */
66 #endif
67 
68 #ifdef CONFIG_ARM64
69 # define ZYNQ_GEM_DBUS_WIDTH	(1 << 21) /* 64 bit bus */
70 #else
71 # define ZYNQ_GEM_DBUS_WIDTH	(0 << 21) /* 32 bit bus */
72 #endif
73 
74 #define ZYNQ_GEM_NWCFG_INIT		(ZYNQ_GEM_DBUS_WIDTH | \
75 					ZYNQ_GEM_NWCFG_FDEN | \
76 					ZYNQ_GEM_NWCFG_FSREM | \
77 					ZYNQ_GEM_NWCFG_MDCCLKDIV)
78 
79 #define ZYNQ_GEM_NWSR_MDIOIDLE_MASK	0x00000004 /* PHY management idle */
80 
81 #define ZYNQ_GEM_DMACR_BLENGTH		0x00000004 /* INCR4 AHB bursts */
82 /* Use full configured addressable space (8 Kb) */
83 #define ZYNQ_GEM_DMACR_RXSIZE		0x00000300
84 /* Use full configured addressable space (4 Kb) */
85 #define ZYNQ_GEM_DMACR_TXSIZE		0x00000400
86 /* Set with binary 00011000 to use 1536 byte(1*max length frame/buffer) */
87 #define ZYNQ_GEM_DMACR_RXBUF		0x00180000
88 
89 #if defined(CONFIG_PHYS_64BIT)
90 # define ZYNQ_GEM_DMA_BUS_WIDTH		BIT(30) /* 64 bit bus */
91 #else
92 # define ZYNQ_GEM_DMA_BUS_WIDTH		(0 << 30) /* 32 bit bus */
93 #endif
94 
95 #define ZYNQ_GEM_DMACR_INIT		(ZYNQ_GEM_DMACR_BLENGTH | \
96 					ZYNQ_GEM_DMACR_RXSIZE | \
97 					ZYNQ_GEM_DMACR_TXSIZE | \
98 					ZYNQ_GEM_DMACR_RXBUF | \
99 					ZYNQ_GEM_DMA_BUS_WIDTH)
100 
101 #define ZYNQ_GEM_TSR_DONE		0x00000020 /* Tx done mask */
102 
103 #define ZYNQ_GEM_PCS_CTL_ANEG_ENBL	0x1000
104 
105 #define ZYNQ_GEM_DCFG_DBG6_DMA_64B	BIT(23)
106 
107 /* Use MII register 1 (MII status register) to detect PHY */
108 #define PHY_DETECT_REG  1
109 
110 /* Mask used to verify certain PHY features (or register contents)
111  * in the register above:
112  *  0x1000: 10Mbps full duplex support
113  *  0x0800: 10Mbps half duplex support
114  *  0x0008: Auto-negotiation support
115  */
116 #define PHY_DETECT_MASK 0x1808
117 
118 /* TX BD status masks */
119 #define ZYNQ_GEM_TXBUF_FRMLEN_MASK	0x000007ff
120 #define ZYNQ_GEM_TXBUF_EXHAUSTED	0x08000000
121 #define ZYNQ_GEM_TXBUF_UNDERRUN		0x10000000
122 
123 /* Clock frequencies for different speeds */
124 #define ZYNQ_GEM_FREQUENCY_10	2500000UL
125 #define ZYNQ_GEM_FREQUENCY_100	25000000UL
126 #define ZYNQ_GEM_FREQUENCY_1000	125000000UL
127 
128 /* Device registers */
129 struct zynq_gem_regs {
130 	u32 nwctrl; /* 0x0 - Network Control reg */
131 	u32 nwcfg; /* 0x4 - Network Config reg */
132 	u32 nwsr; /* 0x8 - Network Status reg */
133 	u32 reserved1;
134 	u32 dmacr; /* 0x10 - DMA Control reg */
135 	u32 txsr; /* 0x14 - TX Status reg */
136 	u32 rxqbase; /* 0x18 - RX Q Base address reg */
137 	u32 txqbase; /* 0x1c - TX Q Base address reg */
138 	u32 rxsr; /* 0x20 - RX Status reg */
139 	u32 reserved2[2];
140 	u32 idr; /* 0x2c - Interrupt Disable reg */
141 	u32 reserved3;
142 	u32 phymntnc; /* 0x34 - Phy Maintaince reg */
143 	u32 reserved4[18];
144 	u32 hashl; /* 0x80 - Hash Low address reg */
145 	u32 hashh; /* 0x84 - Hash High address reg */
146 #define LADDR_LOW	0
147 #define LADDR_HIGH	1
148 	u32 laddr[4][LADDR_HIGH + 1]; /* 0x8c - Specific1 addr low/high reg */
149 	u32 match[4]; /* 0xa8 - Type ID1 Match reg */
150 	u32 reserved6[18];
151 #define STAT_SIZE	44
152 	u32 stat[STAT_SIZE]; /* 0x100 - Octects transmitted Low reg */
153 	u32 reserved9[20];
154 	u32 pcscntrl;
155 	u32 rserved12[36];
156 	u32 dcfg6; /* 0x294 Design config reg6 */
157 	u32 reserved7[106];
158 	u32 transmit_q1_ptr; /* 0x440 - Transmit priority queue 1 */
159 	u32 reserved8[15];
160 	u32 receive_q1_ptr; /* 0x480 - Receive priority queue 1 */
161 	u32 reserved10[17];
162 	u32 upper_txqbase; /* 0x4C8 - Upper tx_q base addr */
163 	u32 reserved11[2];
164 	u32 upper_rxqbase; /* 0x4D4 - Upper rx_q base addr */
165 };
166 
167 /* BD descriptors */
168 struct emac_bd {
169 	u32 addr; /* Next descriptor pointer */
170 	u32 status;
171 #if defined(CONFIG_PHYS_64BIT)
172 	u32 addr_hi;
173 	u32 reserved;
174 #endif
175 };
176 
177 #define RX_BUF 32
178 /* Page table entries are set to 1MB, or multiples of 1MB
179  * (not < 1MB). driver uses less bd's so use 1MB bdspace.
180  */
181 #define BD_SPACE	0x100000
182 /* BD separation space */
183 #define BD_SEPRN_SPACE	(RX_BUF * sizeof(struct emac_bd))
184 
185 /* Setup the first free TX descriptor */
186 #define TX_FREE_DESC	2
187 
188 /* Initialized, rxbd_current, rx_first_buf must be 0 after init */
189 struct zynq_gem_priv {
190 	struct emac_bd *tx_bd;
191 	struct emac_bd *rx_bd;
192 	char *rxbuffers;
193 	u32 rxbd_current;
194 	u32 rx_first_buf;
195 	int phyaddr;
196 	int init;
197 	struct zynq_gem_regs *iobase;
198 	phy_interface_t interface;
199 	struct phy_device *phydev;
200 	ofnode phy_of_node;
201 	struct mii_dev *bus;
202 	struct clk clk;
203 	u32 max_speed;
204 	bool int_pcs;
205 	bool dma_64bit;
206 };
207 
phy_setup_op(struct zynq_gem_priv * priv,u32 phy_addr,u32 regnum,u32 op,u16 * data)208 static int phy_setup_op(struct zynq_gem_priv *priv, u32 phy_addr, u32 regnum,
209 			u32 op, u16 *data)
210 {
211 	u32 mgtcr;
212 	struct zynq_gem_regs *regs = priv->iobase;
213 	int err;
214 
215 	err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
216 				true, 20000, false);
217 	if (err)
218 		return err;
219 
220 	/* Construct mgtcr mask for the operation */
221 	mgtcr = ZYNQ_GEM_PHYMNTNC_OP_MASK | op |
222 		(phy_addr << ZYNQ_GEM_PHYMNTNC_PHYAD_SHIFT_MASK) |
223 		(regnum << ZYNQ_GEM_PHYMNTNC_PHREG_SHIFT_MASK) | *data;
224 
225 	/* Write mgtcr and wait for completion */
226 	writel(mgtcr, &regs->phymntnc);
227 
228 	err = wait_for_bit_le32(&regs->nwsr, ZYNQ_GEM_NWSR_MDIOIDLE_MASK,
229 				true, 20000, false);
230 	if (err)
231 		return err;
232 
233 	if (op == ZYNQ_GEM_PHYMNTNC_OP_R_MASK)
234 		*data = readl(&regs->phymntnc);
235 
236 	return 0;
237 }
238 
phyread(struct zynq_gem_priv * priv,u32 phy_addr,u32 regnum,u16 * val)239 static int phyread(struct zynq_gem_priv *priv, u32 phy_addr,
240 		   u32 regnum, u16 *val)
241 {
242 	int ret;
243 
244 	ret = phy_setup_op(priv, phy_addr, regnum,
245 			   ZYNQ_GEM_PHYMNTNC_OP_R_MASK, val);
246 
247 	if (!ret)
248 		debug("%s: phy_addr %d, regnum 0x%x, val 0x%x\n", __func__,
249 		      phy_addr, regnum, *val);
250 
251 	return ret;
252 }
253 
phywrite(struct zynq_gem_priv * priv,u32 phy_addr,u32 regnum,u16 data)254 static int phywrite(struct zynq_gem_priv *priv, u32 phy_addr,
255 		    u32 regnum, u16 data)
256 {
257 	debug("%s: phy_addr %d, regnum 0x%x, data 0x%x\n", __func__, phy_addr,
258 	      regnum, data);
259 
260 	return phy_setup_op(priv, phy_addr, regnum,
261 			    ZYNQ_GEM_PHYMNTNC_OP_W_MASK, &data);
262 }
263 
phy_detection(struct udevice * dev)264 static int phy_detection(struct udevice *dev)
265 {
266 	int i;
267 	u16 phyreg = 0;
268 	struct zynq_gem_priv *priv = dev->priv;
269 
270 	if (priv->phyaddr != -1) {
271 		phyread(priv, priv->phyaddr, PHY_DETECT_REG, &phyreg);
272 		if ((phyreg != 0xFFFF) &&
273 		    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
274 			/* Found a valid PHY address */
275 			debug("Default phy address %d is valid\n",
276 			      priv->phyaddr);
277 			return 0;
278 		} else {
279 			debug("PHY address is not setup correctly %d\n",
280 			      priv->phyaddr);
281 			priv->phyaddr = -1;
282 		}
283 	}
284 
285 	debug("detecting phy address\n");
286 	if (priv->phyaddr == -1) {
287 		/* detect the PHY address */
288 		for (i = 31; i >= 0; i--) {
289 			phyread(priv, i, PHY_DETECT_REG, &phyreg);
290 			if ((phyreg != 0xFFFF) &&
291 			    ((phyreg & PHY_DETECT_MASK) == PHY_DETECT_MASK)) {
292 				/* Found a valid PHY address */
293 				priv->phyaddr = i;
294 				debug("Found valid phy address, %d\n", i);
295 				return 0;
296 			}
297 		}
298 	}
299 	printf("PHY is not detected\n");
300 	return -1;
301 }
302 
zynq_gem_setup_mac(struct udevice * dev)303 static int zynq_gem_setup_mac(struct udevice *dev)
304 {
305 	u32 i, macaddrlow, macaddrhigh;
306 	struct eth_pdata *pdata = dev_get_platdata(dev);
307 	struct zynq_gem_priv *priv = dev_get_priv(dev);
308 	struct zynq_gem_regs *regs = priv->iobase;
309 
310 	/* Set the MAC bits [31:0] in BOT */
311 	macaddrlow = pdata->enetaddr[0];
312 	macaddrlow |= pdata->enetaddr[1] << 8;
313 	macaddrlow |= pdata->enetaddr[2] << 16;
314 	macaddrlow |= pdata->enetaddr[3] << 24;
315 
316 	/* Set MAC bits [47:32] in TOP */
317 	macaddrhigh = pdata->enetaddr[4];
318 	macaddrhigh |= pdata->enetaddr[5] << 8;
319 
320 	for (i = 0; i < 4; i++) {
321 		writel(0, &regs->laddr[i][LADDR_LOW]);
322 		writel(0, &regs->laddr[i][LADDR_HIGH]);
323 		/* Do not use MATCHx register */
324 		writel(0, &regs->match[i]);
325 	}
326 
327 	writel(macaddrlow, &regs->laddr[0][LADDR_LOW]);
328 	writel(macaddrhigh, &regs->laddr[0][LADDR_HIGH]);
329 
330 	return 0;
331 }
332 
zynq_phy_init(struct udevice * dev)333 static int zynq_phy_init(struct udevice *dev)
334 {
335 	int ret;
336 	struct zynq_gem_priv *priv = dev_get_priv(dev);
337 	struct zynq_gem_regs *regs = priv->iobase;
338 	const u32 supported = SUPPORTED_10baseT_Half |
339 			SUPPORTED_10baseT_Full |
340 			SUPPORTED_100baseT_Half |
341 			SUPPORTED_100baseT_Full |
342 			SUPPORTED_1000baseT_Half |
343 			SUPPORTED_1000baseT_Full;
344 
345 	/* Enable only MDIO bus */
346 	writel(ZYNQ_GEM_NWCTRL_MDEN_MASK, &regs->nwctrl);
347 
348 	if ((priv->interface != PHY_INTERFACE_MODE_SGMII) &&
349 	    (priv->interface != PHY_INTERFACE_MODE_GMII)) {
350 		ret = phy_detection(dev);
351 		if (ret) {
352 			printf("GEM PHY init failed\n");
353 			return ret;
354 		}
355 	}
356 
357 	priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
358 				   priv->interface);
359 	if (!priv->phydev)
360 		return -ENODEV;
361 
362 	priv->phydev->supported &= supported | ADVERTISED_Pause |
363 				  ADVERTISED_Asym_Pause;
364 	if (priv->max_speed) {
365 		ret = phy_set_supported(priv->phydev, priv->max_speed);
366 		if (ret)
367 			return ret;
368 	}
369 
370 	priv->phydev->advertising = priv->phydev->supported;
371 	priv->phydev->node = priv->phy_of_node;
372 
373 	return phy_config(priv->phydev);
374 }
375 
zynq_gem_init(struct udevice * dev)376 static int zynq_gem_init(struct udevice *dev)
377 {
378 	u32 i, nwconfig;
379 	int ret;
380 	unsigned long clk_rate = 0;
381 	struct zynq_gem_priv *priv = dev_get_priv(dev);
382 	struct zynq_gem_regs *regs = priv->iobase;
383 	struct emac_bd *dummy_tx_bd = &priv->tx_bd[TX_FREE_DESC];
384 	struct emac_bd *dummy_rx_bd = &priv->tx_bd[TX_FREE_DESC + 2];
385 
386 	if (readl(&regs->dcfg6) & ZYNQ_GEM_DCFG_DBG6_DMA_64B)
387 		priv->dma_64bit = true;
388 	else
389 		priv->dma_64bit = false;
390 
391 #if defined(CONFIG_PHYS_64BIT)
392 	if (!priv->dma_64bit) {
393 		printf("ERR: %s: Using 64-bit DMA but HW doesn't support it\n",
394 		       __func__);
395 		return -EINVAL;
396 	}
397 #else
398 	if (priv->dma_64bit)
399 		debug("WARN: %s: Not using 64-bit dma even HW supports it\n",
400 		      __func__);
401 #endif
402 
403 	if (!priv->init) {
404 		/* Disable all interrupts */
405 		writel(0xFFFFFFFF, &regs->idr);
406 
407 		/* Disable the receiver & transmitter */
408 		writel(0, &regs->nwctrl);
409 		writel(0, &regs->txsr);
410 		writel(0, &regs->rxsr);
411 		writel(0, &regs->phymntnc);
412 
413 		/* Clear the Hash registers for the mac address
414 		 * pointed by AddressPtr
415 		 */
416 		writel(0x0, &regs->hashl);
417 		/* Write bits [63:32] in TOP */
418 		writel(0x0, &regs->hashh);
419 
420 		/* Clear all counters */
421 		for (i = 0; i < STAT_SIZE; i++)
422 			readl(&regs->stat[i]);
423 
424 		/* Setup RxBD space */
425 		memset(priv->rx_bd, 0, RX_BUF * sizeof(struct emac_bd));
426 
427 		for (i = 0; i < RX_BUF; i++) {
428 			priv->rx_bd[i].status = 0xF0000000;
429 			priv->rx_bd[i].addr =
430 					(lower_32_bits((ulong)(priv->rxbuffers)
431 							+ (i * PKTSIZE_ALIGN)));
432 #if defined(CONFIG_PHYS_64BIT)
433 			priv->rx_bd[i].addr_hi =
434 					(upper_32_bits((ulong)(priv->rxbuffers)
435 							+ (i * PKTSIZE_ALIGN)));
436 #endif
437 	}
438 		/* WRAP bit to last BD */
439 		priv->rx_bd[--i].addr |= ZYNQ_GEM_RXBUF_WRAP_MASK;
440 		/* Write RxBDs to IP */
441 		writel(lower_32_bits((ulong)priv->rx_bd), &regs->rxqbase);
442 #if defined(CONFIG_PHYS_64BIT)
443 		writel(upper_32_bits((ulong)priv->rx_bd), &regs->upper_rxqbase);
444 #endif
445 
446 		/* Setup for DMA Configuration register */
447 		writel(ZYNQ_GEM_DMACR_INIT, &regs->dmacr);
448 
449 		/* Setup for Network Control register, MDIO, Rx and Tx enable */
450 		setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_MDEN_MASK);
451 
452 		/* Disable the second priority queue */
453 		dummy_tx_bd->addr = 0;
454 #if defined(CONFIG_PHYS_64BIT)
455 		dummy_tx_bd->addr_hi = 0;
456 #endif
457 		dummy_tx_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
458 				ZYNQ_GEM_TXBUF_LAST_MASK|
459 				ZYNQ_GEM_TXBUF_USED_MASK;
460 
461 		dummy_rx_bd->addr = ZYNQ_GEM_RXBUF_WRAP_MASK |
462 				ZYNQ_GEM_RXBUF_NEW_MASK;
463 #if defined(CONFIG_PHYS_64BIT)
464 		dummy_rx_bd->addr_hi = 0;
465 #endif
466 		dummy_rx_bd->status = 0;
467 
468 		writel((ulong)dummy_tx_bd, &regs->transmit_q1_ptr);
469 		writel((ulong)dummy_rx_bd, &regs->receive_q1_ptr);
470 
471 		priv->init++;
472 	}
473 
474 	ret = phy_startup(priv->phydev);
475 	if (ret)
476 		return ret;
477 
478 	if (!priv->phydev->link) {
479 		printf("%s: No link.\n", priv->phydev->dev->name);
480 		return -1;
481 	}
482 
483 	nwconfig = ZYNQ_GEM_NWCFG_INIT;
484 
485 	/*
486 	 * Set SGMII enable PCS selection only if internal PCS/PMA
487 	 * core is used and interface is SGMII.
488 	 */
489 	if (priv->interface == PHY_INTERFACE_MODE_SGMII &&
490 	    priv->int_pcs) {
491 		nwconfig |= ZYNQ_GEM_NWCFG_SGMII_ENBL |
492 			    ZYNQ_GEM_NWCFG_PCS_SEL;
493 #ifdef CONFIG_ARM64
494 		writel(readl(&regs->pcscntrl) | ZYNQ_GEM_PCS_CTL_ANEG_ENBL,
495 		       &regs->pcscntrl);
496 #endif
497 	}
498 
499 	switch (priv->phydev->speed) {
500 	case SPEED_1000:
501 		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED1000,
502 		       &regs->nwcfg);
503 		clk_rate = ZYNQ_GEM_FREQUENCY_1000;
504 		break;
505 	case SPEED_100:
506 		writel(nwconfig | ZYNQ_GEM_NWCFG_SPEED100,
507 		       &regs->nwcfg);
508 		clk_rate = ZYNQ_GEM_FREQUENCY_100;
509 		break;
510 	case SPEED_10:
511 		clk_rate = ZYNQ_GEM_FREQUENCY_10;
512 		break;
513 	}
514 
515 #if !defined(CONFIG_ARCH_VERSAL)
516 	ret = clk_set_rate(&priv->clk, clk_rate);
517 	if (IS_ERR_VALUE(ret) && ret != (unsigned long)-ENOSYS) {
518 		dev_err(dev, "failed to set tx clock rate\n");
519 		return ret;
520 	}
521 
522 	ret = clk_enable(&priv->clk);
523 	if (ret && ret != -ENOSYS) {
524 		dev_err(dev, "failed to enable tx clock\n");
525 		return ret;
526 	}
527 #else
528 	debug("requested clk_rate %ld\n", clk_rate);
529 #endif
530 
531 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
532 					ZYNQ_GEM_NWCTRL_TXEN_MASK);
533 
534 	return 0;
535 }
536 
zynq_gem_send(struct udevice * dev,void * ptr,int len)537 static int zynq_gem_send(struct udevice *dev, void *ptr, int len)
538 {
539 	dma_addr_t addr;
540 	u32 size;
541 	struct zynq_gem_priv *priv = dev_get_priv(dev);
542 	struct zynq_gem_regs *regs = priv->iobase;
543 	struct emac_bd *current_bd = &priv->tx_bd[1];
544 
545 	/* Setup Tx BD */
546 	memset(priv->tx_bd, 0, sizeof(struct emac_bd));
547 
548 	priv->tx_bd->addr = lower_32_bits((ulong)ptr);
549 #if defined(CONFIG_PHYS_64BIT)
550 	priv->tx_bd->addr_hi = upper_32_bits((ulong)ptr);
551 #endif
552 	priv->tx_bd->status = (len & ZYNQ_GEM_TXBUF_FRMLEN_MASK) |
553 			       ZYNQ_GEM_TXBUF_LAST_MASK;
554 	/* Dummy descriptor to mark it as the last in descriptor chain */
555 	current_bd->addr = 0x0;
556 #if defined(CONFIG_PHYS_64BIT)
557 	current_bd->addr_hi = 0x0;
558 #endif
559 	current_bd->status = ZYNQ_GEM_TXBUF_WRAP_MASK |
560 			     ZYNQ_GEM_TXBUF_LAST_MASK|
561 			     ZYNQ_GEM_TXBUF_USED_MASK;
562 
563 	/* setup BD */
564 	writel(lower_32_bits((ulong)priv->tx_bd), &regs->txqbase);
565 #if defined(CONFIG_PHYS_64BIT)
566 	writel(upper_32_bits((ulong)priv->tx_bd), &regs->upper_txqbase);
567 #endif
568 
569 	addr = (ulong) ptr;
570 	addr &= ~(ARCH_DMA_MINALIGN - 1);
571 	size = roundup(len, ARCH_DMA_MINALIGN);
572 	flush_dcache_range(addr, addr + size);
573 	barrier();
574 
575 	/* Start transmit */
576 	setbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_STARTTX_MASK);
577 
578 	/* Read TX BD status */
579 	if (priv->tx_bd->status & ZYNQ_GEM_TXBUF_EXHAUSTED)
580 		printf("TX buffers exhausted in mid frame\n");
581 
582 	return wait_for_bit_le32(&regs->txsr, ZYNQ_GEM_TSR_DONE,
583 				 true, 20000, true);
584 }
585 
586 /* Do not check frame_recd flag in rx_status register 0x20 - just poll BD */
zynq_gem_recv(struct udevice * dev,int flags,uchar ** packetp)587 static int zynq_gem_recv(struct udevice *dev, int flags, uchar **packetp)
588 {
589 	int frame_len;
590 	dma_addr_t addr;
591 	struct zynq_gem_priv *priv = dev_get_priv(dev);
592 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
593 
594 	if (!(current_bd->addr & ZYNQ_GEM_RXBUF_NEW_MASK))
595 		return -1;
596 
597 	if (!(current_bd->status &
598 			(ZYNQ_GEM_RXBUF_SOF_MASK | ZYNQ_GEM_RXBUF_EOF_MASK))) {
599 		printf("GEM: SOF or EOF not set for last buffer received!\n");
600 		return -1;
601 	}
602 
603 	frame_len = current_bd->status & ZYNQ_GEM_RXBUF_LEN_MASK;
604 	if (!frame_len) {
605 		printf("%s: Zero size packet?\n", __func__);
606 		return -1;
607 	}
608 
609 #if defined(CONFIG_PHYS_64BIT)
610 	addr = (dma_addr_t)((current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK)
611 		      | ((dma_addr_t)current_bd->addr_hi << 32));
612 #else
613 	addr = current_bd->addr & ZYNQ_GEM_RXBUF_ADD_MASK;
614 #endif
615 	addr &= ~(ARCH_DMA_MINALIGN - 1);
616 
617 	*packetp = (uchar *)(uintptr_t)addr;
618 
619 	invalidate_dcache_range(addr, addr + roundup(PKTSIZE_ALIGN, ARCH_DMA_MINALIGN));
620 	barrier();
621 
622 	return frame_len;
623 }
624 
zynq_gem_free_pkt(struct udevice * dev,uchar * packet,int length)625 static int zynq_gem_free_pkt(struct udevice *dev, uchar *packet, int length)
626 {
627 	struct zynq_gem_priv *priv = dev_get_priv(dev);
628 	struct emac_bd *current_bd = &priv->rx_bd[priv->rxbd_current];
629 	struct emac_bd *first_bd;
630 
631 	if (current_bd->status & ZYNQ_GEM_RXBUF_SOF_MASK) {
632 		priv->rx_first_buf = priv->rxbd_current;
633 	} else {
634 		current_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
635 		current_bd->status = 0xF0000000; /* FIXME */
636 	}
637 
638 	if (current_bd->status & ZYNQ_GEM_RXBUF_EOF_MASK) {
639 		first_bd = &priv->rx_bd[priv->rx_first_buf];
640 		first_bd->addr &= ~ZYNQ_GEM_RXBUF_NEW_MASK;
641 		first_bd->status = 0xF0000000;
642 	}
643 
644 	if ((++priv->rxbd_current) >= RX_BUF)
645 		priv->rxbd_current = 0;
646 
647 	return 0;
648 }
649 
zynq_gem_halt(struct udevice * dev)650 static void zynq_gem_halt(struct udevice *dev)
651 {
652 	struct zynq_gem_priv *priv = dev_get_priv(dev);
653 	struct zynq_gem_regs *regs = priv->iobase;
654 
655 	clrsetbits_le32(&regs->nwctrl, ZYNQ_GEM_NWCTRL_RXEN_MASK |
656 						ZYNQ_GEM_NWCTRL_TXEN_MASK, 0);
657 }
658 
zynq_board_read_rom_ethaddr(unsigned char * ethaddr)659 __weak int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
660 {
661 	return -ENOSYS;
662 }
663 
zynq_gem_read_rom_mac(struct udevice * dev)664 static int zynq_gem_read_rom_mac(struct udevice *dev)
665 {
666 	struct eth_pdata *pdata = dev_get_platdata(dev);
667 
668 	if (!pdata)
669 		return -ENOSYS;
670 
671 	return zynq_board_read_rom_ethaddr(pdata->enetaddr);
672 }
673 
zynq_gem_miiphy_read(struct mii_dev * bus,int addr,int devad,int reg)674 static int zynq_gem_miiphy_read(struct mii_dev *bus, int addr,
675 				int devad, int reg)
676 {
677 	struct zynq_gem_priv *priv = bus->priv;
678 	int ret;
679 	u16 val = 0;
680 
681 	ret = phyread(priv, addr, reg, &val);
682 	debug("%s 0x%x, 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, val, ret);
683 	return val;
684 }
685 
zynq_gem_miiphy_write(struct mii_dev * bus,int addr,int devad,int reg,u16 value)686 static int zynq_gem_miiphy_write(struct mii_dev *bus, int addr, int devad,
687 				 int reg, u16 value)
688 {
689 	struct zynq_gem_priv *priv = bus->priv;
690 
691 	debug("%s 0x%x, 0x%x, 0x%x\n", __func__, addr, reg, value);
692 	return phywrite(priv, addr, reg, value);
693 }
694 
zynq_gem_probe(struct udevice * dev)695 static int zynq_gem_probe(struct udevice *dev)
696 {
697 	void *bd_space;
698 	struct zynq_gem_priv *priv = dev_get_priv(dev);
699 	int ret;
700 
701 	/* Align rxbuffers to ARCH_DMA_MINALIGN */
702 	priv->rxbuffers = memalign(ARCH_DMA_MINALIGN, RX_BUF * PKTSIZE_ALIGN);
703 	if (!priv->rxbuffers)
704 		return -ENOMEM;
705 
706 	memset(priv->rxbuffers, 0, RX_BUF * PKTSIZE_ALIGN);
707 	u32 addr = (ulong)priv->rxbuffers;
708 	flush_dcache_range(addr, addr + roundup(RX_BUF * PKTSIZE_ALIGN, ARCH_DMA_MINALIGN));
709 	barrier();
710 
711 	/* Align bd_space to MMU_SECTION_SHIFT */
712 	bd_space = memalign(1 << MMU_SECTION_SHIFT, BD_SPACE);
713 	if (!bd_space)
714 		return -ENOMEM;
715 
716 	mmu_set_region_dcache_behaviour((phys_addr_t)bd_space,
717 					BD_SPACE, DCACHE_OFF);
718 
719 	/* Initialize the bd spaces for tx and rx bd's */
720 	priv->tx_bd = (struct emac_bd *)bd_space;
721 	priv->rx_bd = (struct emac_bd *)((ulong)bd_space + BD_SEPRN_SPACE);
722 
723 	ret = clk_get_by_name(dev, "tx_clk", &priv->clk);
724 	if (ret < 0) {
725 		dev_err(dev, "failed to get clock\n");
726 		return -EINVAL;
727 	}
728 
729 	priv->bus = mdio_alloc();
730 	priv->bus->read = zynq_gem_miiphy_read;
731 	priv->bus->write = zynq_gem_miiphy_write;
732 	priv->bus->priv = priv;
733 
734 	ret = mdio_register_seq(priv->bus, dev->seq);
735 	if (ret)
736 		return ret;
737 
738 	return zynq_phy_init(dev);
739 }
740 
zynq_gem_remove(struct udevice * dev)741 static int zynq_gem_remove(struct udevice *dev)
742 {
743 	struct zynq_gem_priv *priv = dev_get_priv(dev);
744 
745 	free(priv->phydev);
746 	mdio_unregister(priv->bus);
747 	mdio_free(priv->bus);
748 
749 	return 0;
750 }
751 
752 static const struct eth_ops zynq_gem_ops = {
753 	.start			= zynq_gem_init,
754 	.send			= zynq_gem_send,
755 	.recv			= zynq_gem_recv,
756 	.free_pkt		= zynq_gem_free_pkt,
757 	.stop			= zynq_gem_halt,
758 	.write_hwaddr		= zynq_gem_setup_mac,
759 	.read_rom_hwaddr	= zynq_gem_read_rom_mac,
760 };
761 
zynq_gem_ofdata_to_platdata(struct udevice * dev)762 static int zynq_gem_ofdata_to_platdata(struct udevice *dev)
763 {
764 	struct eth_pdata *pdata = dev_get_platdata(dev);
765 	struct zynq_gem_priv *priv = dev_get_priv(dev);
766 	struct ofnode_phandle_args phandle_args;
767 	const char *phy_mode;
768 
769 	pdata->iobase = (phys_addr_t)dev_read_addr(dev);
770 	priv->iobase = (struct zynq_gem_regs *)pdata->iobase;
771 	/* Hardcode for now */
772 	priv->phyaddr = -1;
773 
774 	if (!dev_read_phandle_with_args(dev, "phy-handle", NULL, 0, 0,
775 					&phandle_args)) {
776 		debug("phy-handle does exist %s\n", dev->name);
777 		priv->phyaddr = ofnode_read_u32_default(phandle_args.node,
778 							"reg", -1);
779 		priv->phy_of_node = phandle_args.node;
780 		priv->max_speed = ofnode_read_u32_default(phandle_args.node,
781 							  "max-speed",
782 							  SPEED_1000);
783 	}
784 
785 	phy_mode = dev_read_prop(dev, "phy-mode", NULL);
786 	if (phy_mode)
787 		pdata->phy_interface = phy_get_interface_by_name(phy_mode);
788 	if (pdata->phy_interface == -1) {
789 		debug("%s: Invalid PHY interface '%s'\n", __func__, phy_mode);
790 		return -EINVAL;
791 	}
792 	priv->interface = pdata->phy_interface;
793 
794 	priv->int_pcs = dev_read_bool(dev, "is-internal-pcspma");
795 
796 	printf("ZYNQ GEM: %lx, phyaddr %x, interface %s\n", (ulong)priv->iobase,
797 	       priv->phyaddr, phy_string_for_interface(priv->interface));
798 
799 	return 0;
800 }
801 
802 static const struct udevice_id zynq_gem_ids[] = {
803 	{ .compatible = "cdns,zynqmp-gem" },
804 	{ .compatible = "cdns,zynq-gem" },
805 	{ .compatible = "cdns,gem" },
806 	{ }
807 };
808 
809 U_BOOT_DRIVER(zynq_gem) = {
810 	.name	= "zynq_gem",
811 	.id	= UCLASS_ETH,
812 	.of_match = zynq_gem_ids,
813 	.ofdata_to_platdata = zynq_gem_ofdata_to_platdata,
814 	.probe	= zynq_gem_probe,
815 	.remove	= zynq_gem_remove,
816 	.ops	= &zynq_gem_ops,
817 	.priv_auto_alloc_size = sizeof(struct zynq_gem_priv),
818 	.platdata_auto_alloc_size = sizeof(struct eth_pdata),
819 };
820